Sony KV-PG21P10 Service Manual ▷ View online
– 21 –
KV-PG21P10
RM-952
No NICAM
1 = NICAM search is disable in any TV system, 0 = NICAM search operates
US ST
(Reserved for NTSC model)
1 V-Curve
1 = using common volume curve for every mode and every TV system
(for monaural model)
0 = another volume curve available for video mode and M system
XTAL SEL
00 = only 4.43 XTAL
01 = only 3.58 XTAL
10 = not used
11 = both 4.43 and 3.58 XTAL
Other optional function will be enabled if the corresponding bit is set to 1.
No Bal.
1 = no balance in analog select items, 0 = balance included
(for AV stereo model)
SPC SOUND
1 = Space Sound available, 0 = not available
Korean ST
(Reserved for NTSC model)
H.K. Bil.
1 = NICAM bilingual available (No NICAM stereo), 0 = not available
(for monaural model)
Other optional function will be enable if the corresponding bit is set to 1.
No. 50 OP3
Item
KV-PG21P10
SECAM
1
HDEV
0
US ST
0
1 V-Curve
0
XTAL SEL
1
1
No. 4F OP2
No NICAM
0
2nd Lang.
1
Item
KV-PG21P10
H.K. Bil.
0
No Bal.
0
Auto TV Sys.
0
SPC SOUND
0
PIC Rot.
0
Thai Bil.
0
Korean ST
0
VM
0
– 22 –
KV-PG21P10
RM-952
4-3. PICTURE QUALITY ADJUSTMENT
SUB COLOR ADJUSTMENT
1. Select Video.
2. Input a PAL color-bar.
3. Set to the following condition:
2. Input a PAL color-bar.
3. Set to the following condition:
PICTURE 100%, BRIGHTNESS 50%, COLOR 50%
4. Connect an oscilloscope to pin 1 (B OUT) of CN300, A board.
5. Set to Service Mode and select 13 ‘SC1’ with 1 and 4 of
5. Set to Service Mode and select 13 ‘SC1’ with 1 and 4 of
the commander then adjust to VB2=VB3=VB4 with 3 and
6.
6.
6. Press
[MUTING]
→ - of the commander to write the data.
7. Adjust 13 ‘SC1’ as step 2 to 5 when receiving NTSC
color-bar.
SUB HUE ADJUSTMENT
1. Select Video.
2. Input a NTSC 3.58, color-bar into Video/TV mode.
3. Set the following condition:
2. Input a NTSC 3.58, color-bar into Video/TV mode.
3. Set the following condition:
PICTURE 100%, BRIGHTNESS 50%, COLOR 50%
4. Connect an oscilloscope to pin 1 (B OUT) of CN300, A
board.
5. Select 11"SHU" with 1 and 4 of the commander by setting
to Service Mode and adjust to VB1=VB2=VB3=VB4 with
3 and 6.
3 and 6.
The highest level of VB1,VB2,VB3,VB4 must be aligned at
the same line. Ideal difference level between VB2 and VB3
should be within ± 110mV.
the same line. Ideal difference level between VB2 and VB3
should be within ± 110mV.
6. Press
[MUTING]
→ - of the commander to write the data.
7. Select TV channel with NTSC 3.58 and repeat 3 to 5.
8. Press
8. Press
[MUTING]
→ - of the commander to write the data.
9. Single system model with NTSC 4.43, select TV channel with
NTSC 4.43 and repeat 3 to 5.
VB1
VB2
VB3
VB4
VB2 = VB3 = VB4
VB2 = VB3 = VB4 (Difference is within 70mV)
VB1
VB2
VB3
VB4
VB1 = VB2 = VB3 = VB4
4-4. DEFLECTION ADJUSTMENT
NORMAL MODE (50Hz)
1.
Set to Service mode.
2.
Input PAL color bar.
3.
Using the 1 and 4 button, select category GEO
(Service Mode).
(Service Mode).
4.
Raise/lower the data using the 3 and 6 buttons.
Select and adjust the following items to obtain optimum
image.
Select and adjust the following items to obtain optimum
image.
Service Item
GEO : 00
HPS
H POSITION
01
HSZ
H SIZE
02
PAP
PIN AMP
03
CPN
CORNER PIN
04
TLT
TLT
05
VSL
V SLOPE
06
VAP
VERTICAL AMPLITUDE
07
SCO
S CORRECTION
08
VPS
V SHIFT
NORMAL MODE (60Hz)
5. Input 525/60Hz signal.
6. Using the 1 and 4 buttons select category GEO (Service
5. Input 525/60Hz signal.
6. Using the 1 and 4 buttons select category GEO (Service
Mode).
7. Select and adjust the following items to obtain obtimum
image.
Raise/lower the data with the 3 and 6 buttons.
Raise/lower the data with the 3 and 6 buttons.
Service Item
GEO : 00
HPS
H POSITION
01
HSZ
H SIZE
02
PAP
PIN AMP
03
CPN
CORNER PIN
04
TLT
TILT
05
VSL
V SLOPE
06
VAP
VERTICAL AMPLITUDE
07
SCO
S CORRECTION
08
VPS
V SHIFT
4-5. A BOARD AJUSTMENT AFTER IC003
(MEMORY) REPLACEMENT
1.
Enter to Service Mode.
2.
Press commander buttons 5 and - (Data Initialize), and
2 and - (Data Copy) to initialize the data.
2 and - (Data Copy) to initialize the data.
3.
Call each item number and check if the respective screen
shows the normal picture.
In cases where items are not well adjusted, rectify the fine
adjustment.
Write the data per each item number (
shows the normal picture.
In cases where items are not well adjusted, rectify the fine
adjustment.
Write the data per each item number (
[MUTING]
+-).
4.
Select item numbers 4E ‘OP0’, 4F ‘OP1’, 50 ‘OP2’ and
respectively set the bit per model with command buttons
3 and 6 .
respectively set the bit per model with command buttons
3 and 6 .
5.
Press commander buttons 8 and - (Test Normal) to return
to the data that was set on the shipment from the factory.
(This will also cancel Service Mode.)
to the data that was set on the shipment from the factory.
(This will also cancel Service Mode.)
– 23 –
KV-PG21P10
RM-952
4-6. PICTURE DISTORTION ADJUSTMENT
Item Number 00 – 08
01
HSZ (H SIZE)
04
TLT (TILT)
06
VAP (VERTICAL AMPLITUDE)
00
HPS (H POSITION)
02
PAP (PIN AMPLITUDE)
03
CPN (CORNER PIN)
05
VSL (V SLOPE)
08
VPS (V SHIFT)
07
SCO (S CORRECTION)
Click on the first or last page to see other KV-PG21P10 service manuals if exist.