DOWNLOAD Sony KV-LS212M50 Service Manual ↓ Size: 7.06 MB | Pages: 73 in PDF or view online for FREE

– 12 –

1.  Spacing between HV cable and other conductive part's surface is 1mm/kV or more.
2.  Spacing between HV cable's and enclosure with ventilation or the edge where 
 

terminal bracket and rear cover meet: 10 mm or more.

Rear view of Lead Assy, Focus & G2, connected from 
FBT A brd to CV brd. 

Lead Assy, G2

Lead Assy, Focus

Conn. Assy, 5P (200V)

Earth Assy, Coating

Lead Assy, Focus

Lead Assy,

G2

Keep Lead Assy, 

G2 away from 

Heat Sink.

Keep Lead Assy, 

G2 away from 

HV Cable 

(at least 1mm/kV)

Purse Lock Ø5

Use this as a reference to dress 

ECA, Lead Assy, Focus & G2.

Earth Assy,

Coating

Lead Assy, G2

Lead Assy, Focus

Dress tight at the portion to 
avoid wire touches rear cover. 

Purse Lock Ø5

Conn Assy, 7P

Rotational Coil Conn

Non-rotational Coil 

Rotational Coil

Purse Lock Ø5

Keep Lead Assy, Earth 

away from heat sinks 

Keep Lead Assy, Earth
away  from heat sinks 

Lead Assy, Earth

Lead Assy, Earth

Conn Assy, 7P

Lead Assy, Earth

UL Wire

Connector Assy, 7P

Purse Lock Ø5

Lead Assy, Earth

Connector Assy, 7P

UL Wire

Rotational Coil Conn.

UL Tape

Purse Lock Ø5

UL Wire (1-923-000-81)

DY

90∞

Wire from 

Rotation Coil

Rotation Coil

UL Wire (1-923-000-81)

– 13 –

Place purse lock Ø9 after the exit of DGC Conn from DGC

DGC

Purse Lock Ø9

Black tape

DGC Conn

outlet

180 ± 5 mm

HV Holder Combi

A)  Spacing between HV cable and conductive part's    
 

surface --> 1mm/kV or more

B)  Spacing between edge of anode cap and conductive 
 

parts --> 0.5mm/kV or more

C)  Spacing between HV cable & enclosure with   
 

ventilation (i.e. Rear Cover side) --> 10mm or more

45°

HV Holder Combi

Purse Lock Ø9

Fix the bigger diameter hook of HV 
Holder Combi on the right side of black 
tape & at horizontal bending of DGC, 
then use purse lock Ø9 to secure HV 
Holder Combi to DGC

B

A

A

A

A

C

Dress HV Holder 
Combi with Purse Lock 
Ø9 as shown

HV Holder Combi

CAUTION:
Keep HV cable facing inwards DY to keep HV cable 
away from ventilation side of rear cover --> 10mm or more.
Ensure TVSR 1mm/kV is kept from HV cable to 
DY & other conductive parts

AC Cord Holder

AC Power Cord

Dress AC Power Cord with 
purse lock at rear cover

Purse Lock Ø8

Make sure AC Power Cord is
dressed between bottom cover 
boss and rail guide

– 14 –

The following adjustments should be made when a complete
realignment is required or a new picture tube is installed.

The controls and switch should be set as follows unless
otherwise noted:

Picture control ......................................................... NORMAL
Brightness control ................................................... NORMAL

Perform the adjustments in order as follows:
1. Beam Landing
2. Convergence
3. Focus
4. G2 (SCREEN)
5. White Balance

Note: Test Equipment Required
1. Pattern Generator
2. Degausser
3. DC Power Supply
4. Digital Multimeter

Preparation :
• Feed in the white pattern signal.
• Before starting, degauss the entire screen with the

degausser.

• In order to reduce the geomagnetism on the set's

picture tube, face it east or west.

1. Input a raster signal with the pattern generator.
2. Loosen the deflection yoke mounting screw, and set the

purity control to the center as shown below.

3. Set the raster signal of the pattern generator to green.
4. Move the deflection yoke (DY) backward and adjust the

purity control so that green is in the center and blue and
red are at the sides evenly.

5. Then move the DY forward and adjust so that the entire

screen becomes green.

6. Now switch over raster signal to red then blue and

confirm the condition.

...................................................................................................................................................................................................................... ...........

5. Oscilloscope
6. Landing Checker
7. XCV Adjuster

Purity control

Red

Blue

Green

7. When the position of the DY is determined, tighten it

with the DY mounting screw.

8. If the beam does not land correctly in all corners of the

screen, use magnet disc to correct it.

Preparation :
• Before starting, perform FOCUS adjustment.
• Picture mode STANDARD.
• Receive dot/cross hatch pattern.

Purity control
corrects this area.

Disc magnets or rotatable
disc magnets correct these
areas (a-d).

Deflection yoke positioning
corrects these areas.

a

b

b

c

c

d

d

a

Center dot

R    G    B

R

G

B

4 pole magnet

C/CV Board

– 15 –

1. (Moving vertically), adjust the 4 pole magnet to converge

red, green and blue dots in the center of the screen.

2. Tilt the 4 pole magnet and adjust static convergence to

open or close the 4 pole magnet.

3. When the 4 pole magnet is moved in the direction of

arrow A and B, the red, green and blue dots moves as
shown below:

If the blue dots does not converge with the red and green
dots, use the 6 pole magnet to adjust in the manner
described below.

R

R

G

G

B

B

A

B

B

A

R G

B

R

G

B

R

G B

R

B

R

G

G

G

B

R

B

6 Pole Magnet

4 Pole Magnet

DY pocket

Purity

6 Pole

Magnet

4 Pole

Magnet

Preparation :
• Before starting this adjustment, adjust the horizontal

and vertical static convergence.

Input cross hatch pattern.
i)

TLH
Adjust the horizontal convergence of red and blue dots
by inserting TLH Correction Plate to the DY pocket (left
or right).

ii)

YCH
Adjust YCH to balance Y axis.

iii) TLV

Adjust the vertical convergence of red and blue dots.

iv) XCV

Adjust XCV to balance X-axis.

Affix a Piece A (90), Convergence Correct/Permaloy Assy
Correction to the misconverged areas.

TLV

R B

YCH

R

B

XCV

B

R

TLH

B

R

TLV

ON DY:

TLV

XCV

YCH

DY pocket

DY pocket

TLH Plate

XCV

b

a

c

d

a-d : screen-corner
        misconvergence

a1~d1:Piece A (90), Convergence Correct

or

Permaloy Assy Correction

a1

b1

c1

d1

B

R

G

G

R

B