DOWNLOAD Sony KV-HW21M83 Service Manual ↓ Size: 5.48 MB | Pages: 87 in PDF or view online for FREE

23

Additional Information

Place the TWEETER on top of your TV.

Peel off the protective sheet at the bottom of the cable clips, stick the 6
cable clips on the rear of your TV and slide the wires through the cable clips.

Connect the wires to the TWEETER terminals at the rear of your TV. The
plain wire should be connected to the 3 red terminal and the striped wire
to the # black terminal.

Notes
• Connect only the supplied TWEETER; otherwise your TV may malfunction.
• Unplug your TV from the wall outlet when connecting the TWEETER.
• To prevent a malfunction caused by a short circuit of the terminals, make sure that none of the

TWEETER wire strands stick out, making contact with the neighbouring speaker terminal.

You can enjoy high quality sound by connecting the TWEETER.

B 

TWEETER

01GB07ADJ-MIX.p65

12/16/03, 8:57 AM

23

Black

24

Additional Information

x

Connecting to the video input terminal ( t )

L

R

(MONO)

2

L

R

R

1

L

Y

C

B

C

R

(MONO)

(MONO)

Note
• If you connect a VCR to 8 (antenna input), preset the signal output from the VCR to the

program number 0 on the TV (see page 21).

x

B 

You can enjoy high quality sound by connecting the 3D WOOFER as follows:

Notes
• Connect only the supplied 3D WOOFER; otherwise your TV may malfunction.
• Unplug your TV from the wall outlet when connecting the 3D WOOFER.
• To prevent a malfunction caused by a short circuit of the terminals, make sure that none of the 3D

WOOFER wire strands stick out, making contact with the neighbouring 3D WOOFER terminal.

 

01GB07ADJ-MIX.p65

12/16/03, 8:57 AM

24

Black

25

Additional Information

L

R

R

1

L

Y

C

B

C

R

(MONO)

(MONO)

Y (green)

Y

C

B

 (blue)

C

B

, P

B

, C

b

 or B-Y

C

R

 (red)

C

R

, P

R

, C

r

 or R-Y

 

L

R

R

1

L

Y

C

B

C

R

(MONO)

(MONO)

Connecting to the monitor output terminal ( T )

Notes
• If your DVD player can output interlace and progressive mode signals, select the interlace

output when connecting to 

 (component video input) on your TV. Your TV can receive

either 525i/60Hz or 625i/50Hz interlace signals.

• Some DVD player terminals may be labeled differently:

• If you select “DVD” on your TV screen, the signal from the T (monitor output) jacks will not

be output properly. This does not indicate a malfunction.

01GB07ADJ-MIX.p65

12/16/03, 8:57 AM

25

Black

26

Additional Information

x

If you find any problem while viewing your TV, please check the following
guide. If any problem persists, contact your Sony dealer.

24

–

21

–

–

21

24

9

8

• Check the antenna cable and connection

on the TV, VCR and at the wall.

• Check the antenna setup.

Contact a Sony dealer for advice.

• Display the “Channel Setup” menu and

select “Manual Program” to preset the
channel again.

• Try using a booster.

• Turn off or disconnect the booster if it is in

use.

• Display the “Channel Setup” menu and

select the appropriate  “TV System”.

• Check the power cord, antenna and VCR

connections.

• Press 

 ?/1

 (power).

• Press ! (main power) on the TV to turn

off the TV for about five seconds, then
turn it on again.

• The connection is loose

or the cable is
damaged.

• The antenna setup is

inappropriate.

• Channel presetting is

inappropriate or
incomplete.

• Signal transmission is

low.

• Broadcast signals are

too strong.

• The TV system setting

is inappropriate.

• The power cord,

antenna or VCR is not
connected.

• The TV is not turned

on.

01GB08ADV-MIX.p65

12/16/03, 8:58 AM

26

Black