DOWNLOAD Sony KV-HR36K90 Service Manual ↓ Size: 8.49 MB | Pages: 127 in PDF or view online for FREE

– 45 –

No.

Name

00

APC

01

TSY

02

AFM

03

DBL

04

SSO

05

SCH

NTSC Only

06

SCA

NTSC Only

07

DMG

08

VSN

09

LBB

10

23P

11

DF

36

12

DQP

26

13

VLIM

50/60/ZM/WZ

14

TUT1

5

15

TUT2

5

16

TUT3

5

17

TUTW

5

18

3NR

19

SIG

TV/Video(HD/DVD)

20

NSIG

TV/Video(HD/DVD)

13

VLIM

15

15

15

15

No.

Name

RF

Video

19

SIG

0

5

20

NSIG

0

20

Wide V-Center Limit
Tune Wait Time Mode1 (Max) 30[ms] + 10[ms] * service_data

No-Signal Detect number of lock detect count.
No-Signal Detect number of unlock detect counter.

Tune Wait Time Mode2 (Max) 30[ms] + 10[ms] * service_data
Tune Wait Time Mode3 (Max) 30[ms] + 10[ms] * service_data
Tune Wait Time 6 point sense
3D-NR INIT (User Reset or Test Reset)

Disable Blueback function
Speed CH Search Selection
CH Selection for Shipping Condition

Functionality

Function

APC Switch
TV System Selection under searching with Auto TV System
Auto FM switch

ZOOM 60Hz

Cable/Air Selection for Shipping Condition

Signa-Detect

Functionality

Disable Menu-operation Guide
Enable Noise Reduction in Video Mode
Lower Blue Back Intensity
2/3 Pull Down Mode 0: Force OFF, 1: Auto
DF_PHA
DQP_PHA

Range

Standards

Remarks

No.

Functionality

Name

V-Center Limit

WIDEZOOM

50Hz

WIDEZOOM

60Hz

ZOOM 50Hz

1
2
1
0
1
1
1
0
0
0
1

*2

*2

*1

1

– 46 –

No.

Name

00

OP0

60

52

Optional Bits 0

01

OP1

107

Optional Bits 1

02

OP2

Optional Bits 2

03

OP3

104

Optional Bits 3

04

OP4

Optional Bits 4

Remarks

Functionality

Range

Standards

Function

3

53

TAIWAN

KOREAN

52

43

119

8

No.

Name

00

COM

Service Command

Remarks

Functionality

Range

Standards

Function

– 47 –

•

The following adjustments should be made when a complete
realignment is required or a new picture tube is installed.

•

These adjustments should be performed with rated power
supply voltage unless otherwise noted.

Controls and switches should be set as follows unless otherwise

noted:

PICTURE control ........................................................... normal
BRIGHTNESS control................................................... normal

Perform the adjustments in the following order :

1. Beam Landing
2. Convergence
3. Focus
4. White Balance
Note : Test Equipment Required.

1. Color-bar/Pattern Generator
2. Degausser
3. Oscilloscope

...................................................................................................................................................................

Preparation :
•

In order to reduce the influence of geomagnetism on the set’s
picture tube, face it east or west.

•

Switch on the set’s power and degauss with the degausser.

1. Set to the service mode.
2. Set to the coarse CONV and LAND adjustment mode.
3. Move the marker in the order as shown in the figure and set

its data to “0”.

Landing: 1 

t 2 t 3 t 4 t 5 t 6 t 7

Convergence: 1 

t 2 t 3 t 4 t 5

1. Input a white signal with the pattern generator.

Contrast
Brightness

2. Position neck assy as shown in Fig4-1.
3. Set the pattern generator raster signal to a green raster.
4. Move the deflection yoke to the rear and adjust with the pu-

rity control so that the green is at the center and the blue and
the red take up equally sized areas on each side.
(See Figures 4-2 through 4-4.)

5. Move the deflection yoke forward and adjust so that the

entire screen is green. (See Figure 4-3.)

6. Switch the raster signal to blue, then to green and verify the

condition.

7. When the position of the deflection yoke has been decided,

fasten the deflection yoke with the screws and DY spacers.

normal

}

Neck assy

G2

G1

G3

Behind the G2 edge

•

Move the marker with the buttons 

R ,r , T  and t on the

remote commander.”
Press “ENTER” to decide the position.
Change the data with the buttons 

R ,r , T  and t on the

remote commander.

– 48 –

Preparation :
•

Before starting this adjustment, adjust the focus, horizontal
size and vertical size.

•

Set the Picture Mode to “STANDARD”.

•

Cross hatch / Dot pattern.

1. (Moving horizontally), adjust the H.STAT control so that the

red, green and blue dots are on top of each other at the center
of the screen.

2. (Moving vertically), adjust the V.STAT magnet so that the

red, green and blue dots are on top of each other at the center
of the screen.

3. If the H.STAT variable resistor cannot bring the red, green

and blue dots together at the center of the screen, adjust the
horizontal convergence with the H.STAT variable resistor and
the V.STAT magnet in the manner given below.
(In this case, the H.STAT variable resistor and the V.STAT
magnet influence each other, so be sure to perform adjust-
ments while tracking.)

Red

Blue

Green

Purity control
corrects this area.

Deflection yoke positioning
corrects these areas.

Center dot

R    G    B

R

G

B

H. STAT VR

V. STAT

Magnet

RV9001

H. STAT

C Board