Sony KV-G21L3 Service Manual ▷ View online
– 17 –
KV-G21L3
RM-883
3-3. FOCUS ADJUSTMENT
Adjust FOCUS control on the flyback transformer for the best
focus.
Note: Screen VR is not use.
SERVICE
MUTING
1 F
DATA
RDR
Adjustment Item
09
Item number
WRITE
1 F
RDR
09
0
Executes the writing
a. AN ITEM OF ADJUSTMENT
b. METHOD OF CANCELLATION FROM SERVICE
MODE
Set the standby condition (Press POWER button on the
commander) and then press POWER button again, hereupon it
becomes TV mode.
c. METHOD OF WRITE FOR MEMORY
1) Set to Service Mode.
2) Press 1 (UP) and 4 (DOWN) to select the item of
adjustments.
3) Press [MUTING] button and it will indicate WRITE on screen.
4) Press - button to write into memory.
d. MEMORY WRITE CONFIRMATION METHOD
1) After adjustment, pull out the plug from AC outlet, and then
plug into AC outlet again.
2) Turn the power switch ON and set to Service Mode.
3) Call the adjusted items again to confirm adjustments were made.
Item
number
number
Note
Adjustment
item
item
Initial DATA
09
RDR
25
WHITE POINT R
0A
GDR
20
WHITE POINT G
0B
BDR
20
WHITE POINT B
3-4. G2 (SCREEN) AND WHITE BALANCE
ADJUSTMENTS
1. G2 (SCREEN) ADJUSTMENT (RV701)
1) Set the PICTURE and BRIGHTNESS to normal.
2) Put to VIDEO input mode without signals.
3) Connect R, G and B of the C board cathode to the oscilloscope.
4) Adjust G2 (RV701) volume to the value below.
2. WHITE BALANCE ADJUSTMENTS
1) Set to Service Mode.
2) Input an entire white signal.
3) Set the PICTURE to maximum.
4) Select RDR(09) with 1 and 4 , and then set the level to 25
with 3 and 6 .
5) Select GDR(0A) and BDR(0B) with 1 and 4 and adjust the
level with 3 and 6 for the best white balance.
6) Write into the memory by pressing [MUTING] then - .
0 V
177 ± 2 V DC
FOCUS
SCREEN
(NOT USED)
(NOT USED)
FLYBACK TRANSFORMER (T851)
177±2V
– 18 –
KV-G21L3
RM-883
SECTION 4
SELF DIAGNOSIS FUNCTION
If no acknowledgement is returned from a device which is turned "ON", the device has a problem.
In this case, one of the LED's responding to the problem device will flicker a defined number of times.
Flickering is operated by lighting the LED's for 60ss each time.
The flickering frequency responding to each failed device is shown below.
All the devices are checked one after another from the left of the table.
If an error is found, the responding LED will start flickering.
So, if more than 1 device have failed, only the one on the left side will flicker.
Device
Flickering
Frequency
NONVOLATILE
MEMORY
1
—
—
Y/C JUNGLE
3
—
—
—
—
—
—
– 19 –
KV-G21L3
RM-883
SECTION 5
CIRCUIT ADJUSTMENTS
Entering service mode
With the unit on standby
↓
DISPLAY
↓
5
↓
VOL (+)
↓
POWER
The operation sequence puts the unit into service mode.
5-1. ADJUSTMENTS WITH COMMANDER
Service adjustments are made with the RM-883 that comes with
this unit.
[1], [4]
Raise/lower the service item number
[3], [6]
Raise/lower the data
[MUTING]
Writes
[0]
Executes the writing
SELECT
p
PIC MODE
p
SOUND
MODE
VOL
PROGR
RM-883
g
POWER
DISP
REVEAL
MUTING
TV
VIDEO
HOLD
TEXT
A/B
ENLARGE
WIDE/
V-ZOOM
WAKE UP
INDEX
SLEEP
TEXT CLR
+
+
1
2
3
4
6
7
8
9
0
+
p
–
p
5
TV
[7], [0]
All data becomes the values in memory
[8], [0]
All user control goes to the standard state
[5], [0]
Service data initialization (Be sure not to use
usually).
[2], [0]
Write 50Hz adjustment data to 60Hz, or
viceversa.
The screen display is :
SERVICE
Mode
08
Data
RGB
50
Depends on the signals
PAL, SECAM : 50
NTSC : 60
PAL, SECAM : 50
NTSC : 60
1000
0000
Adjustment item
00
Item number
[1], [4]
Select the adjustment item.
↓
[3], [6]
Raise/lower the data.
↓
[MUTING]
Writes
↓
[0]
Executes the writing.
RM-883
– 20 –
KV-G21L3
RM-883
5-2. ADJUSTMENT METHOD
Item Number 08
This explanation uses V-SHIFT as an example.
1. Select 08 V-SHIFT with the [1] and [4] buttons.
2. Raise/lower the data with the [3] and [6] buttons.
3. Select the optimum state. (The standard is 0F for PAL
reception.)
4. Write with the [MUTING] button. (The SERVICE display will
change to WRITE)
5. Execute the writing with the [0] button. (The WRITE
display will be changed back to SERVICE.)
Use the same method for Items Number 00-33. Use [1] and [4] to
select the adjustment item, use [3] and [6] to adjust, write with
[MUTING], then execute the write with [0].
Write executed with
[0]
.
Written with
the [MUTING]
.
WRITE
WRITE
GREEN
0C
VSF
08
SERVICE
50
50
50
GREEN
0C
VSF
08
GREEN
The WRITE display
will be changed back
to SERVICE.
The WRITE display
will be changed back
to SERVICE.
0C
VSF
08
Adjust with the
[3]
and
[6]
buttons.
Click on the first or last page to see other KV-G21L3 service manuals if exist.