DOWNLOAD Sony KV-DR34M97 Service Manual ↓ Size: 17.82 MB | Pages: 127 in PDF or view online for FREE

– 10 –

• After removing the anode, short circuit the anode of the picture tube and the anode cap to the metal chassis, CRT

shield or carbon paint on the CRT.

• REMOVING PROCEDURES

1 Turn up one side of the rubber cap in the direction

a.

2 Using a thumb pull up the rubber cap firmly in the direc-

b.

3 When one side of the rubber cap is separated from the

c.

• HOW TO HANDLE AN ANODE-CAP

1 Do not damage the surface of anode-caps with

2 Do not press the rubber too hard so as not to

3 Do not turn the foot of rubber over too hard.

a

a

b

b

c

 Anode Button

– 11 –

REF NO.

DESCRIPTION

QUANTITY

PART NO.               REMARK

J-1

TOOL(20P),SERVICE

1

3-702-763-01         For A to BC1 board extension

1

                              For A to P board extension

J-2

TOOL(40P),SERVICE

1

3-702-764-01         For A to B3 board extension

J-3

TOOL(50P-A),SERVICE

1

3-702-765-01         For D to D5 board extension

J-4

TOOL(7PX2),SERVICE

1

3-702-775-01         For  A  to  V2  board extension

                              (not used for this model)

D Board

D5 Board

B3 Board

J Board

P Board

A Board

F1 Board

BC1 Board

V2 Board (not used for this model)

H1 Board

VM Board

H2 Board

C Board

DH Board

– 12 –

If a customer faces some setting problem that cannot be solved, using the "RESET" function some items will be
reset to its original setting (shipping condition)

There are 2 ways to access to the "RESET" Function:-

a) By pressing "RESET" button on the Remote Commander.
b) By pressing "MENU" button on the Front Key Input and hold it down for 5 seconds.

Sequential to the resetting operation (either methods being used in No. 2), TV set would shut down once and
automatically turn on again. The power-off duration is expected to be about 500msec. An OSD message,
"RESET" tentatively will be displayed for 10 sec after IK status gets stable.
As a result, some items will be reset to an initial condition (shipment condition) wheareas some other remains at
the last selection by user.

Items that remains at the last selection by user

Reset Items

Program No., PIC rotation, OSD Language,

Fine tuning, TV System, Skip

Video input

RF

Volume

30

DRC-MF

DRC1250

Picture mode

DYNAMIC

Sound mode

DYNAMIC

Surround mode

OFF

Color system(video)

AUTO

Multi picture(PIP)

OFF

PIP position

Bottom-right

OSD recall

OFF

Intelligent volume

OFF

ECO mode

OFF

Color system(RF)

AUTO*

Antenna sensitivity

HIGH*

Stereo mode

STEREO/NICAM*

Bilingual mode

MAIN*

High-deviation mode

AUTO*

Child lock

OFF*

Wide mode

OFF

Game mode

OFF

Teletext mode

OFF

Sleep timer

OFF

Wake-up timer

OFF

Sound muting

OFF

3DNR

ON

*= only when in RF mode

– 13 –

• The following adjustments should be made when a complete

realignment is required or a new picture tube is installed.

• These adjustments should be performed with rated power

supply voltage unless otherwise noted.

Controls and switches should be set as follows unless otherwise
noted:
PICTURE control ...........................................................  normal
BRIGHTNESS control ...................................................  normal

Perform the adjustments in the following order :

1. Beam Landing
2. Convergence
3. Focus
4. White Balance
Note :  Test Equipment Required.

1. Color-bar/Pattern Generator
2. Degausser
3. Oscilloscope

normal

Neck assy

G2

G1

G3

Align the edge of 
the neck assy with 
the edge of the G3 grid. 

Red

Blue

Green

Preparation :
• In order to reduce the influence of geomagnetism on the set's

picture tube, face it east or west.

• Switch on the set's power and degauss with the degausser.

1. Input a white signal with the pattern generator.

Contrast
Brightness

2. Position neck assy as shown in Fig 5-1.
3. Set the pattern generator raster signal to a green raster.
4. Move the deflection yoke to the rear and adjust with the

purity control so that the green is at the center and the blue
and the red take up equally sized areas on each side.
(See Figures 5-1 through 5-3.)

5. Move the deflection yoke forward and adjust so that the

entire screen is green. (See Figure 5-2.)

6. Switch the raster signal to blue, then to red and verify the

condition.

7. When the position of the deflection yoke has been decided,

fasten the deflection yoke with the screws and DY spacers.

8. If the beam does not land correctly in all the corners, use a

magnet to adjust it.
(See Figure 5-4.)

Purity control
corrects this area.

Disk magnets or rotatable
disk magnets correct these
areas (a-d).

Deflection yoke positioning
corrects these areas.

a

b

b

c

c

d

d

a

}