DOWNLOAD Sony KV-DR29M50B Service Manual ↓ Size: 15.15 MB | Pages: 106 in PDF or view online for FREE

– 9 –

REF NO.

DESCRIPTION

QUANTITY

PART NO.               REMARK

J-1

TOOL(20P),SERVICE

1

3-702-763-01         For A to BC1 board extension

J-2

TOOL(40P),SERVICE

1

3-702-764-01         For A to B3 board extension

J-3

TOOL(50P-A),SERVICE

1

3-702-765-01         For D to D5 board extension

D Board

D5 Board

B3 Board

J Board

P Board

A Board

F1 Board

BC2 Board

H1 Board

VM Board

H2 Board

C Board

– 10 –

If a customer faces some setting problem that cannot be solved, using the "RESET" function some items will be
reset to its original setting (shipping condition)

There are 2 ways to access to the "RESET" Function:-

a) By pressing "RESET" button on the Remote Commander.
b) By pressing "MENU" button on the Front Key Input and hold it down for 5 seconds.

Sequential to the resetting operation (either methods being used in No. 2), TV set would shut down once and
automatically turn on again. The power-off duration is expected to be about 500msec. An OSD message,
"RESET" tentatively will be displayed for 10 sec after IK status gets stable.
As a result, some items will be reset to an initial condition (shipment condition) wheareas some other remains at
the last selection by user.

Items that remains at the last selection by user

Reset Items

Program No.,  PIC rotation, OSD Language,

Fine tuning, TV System, Skip

Video input

RF

Volume

30

DRC-MF

DRC1250(except KV-DR29N90B)

DRC-MF

DRC1050(KV-DR29N90B)

Picture mode

DYNAMIC

Sound mode

DYNAMIC

Surround mode

OFF

Color system(video)

AUTO

Multi picture(PIP)

OFF(not used for these models)

PIP position

Bottom-right(not used for
these models)

OSD recall

OFF

Intelligent volume

OFF

ECO mode

OFF

Color system(RF)

AUTO*

Antenna sensitivity

HIGH*(not used for these models)

Stereo mode

STEREO/NICAM*
(except KV-DR29M81)

Bilingual mode

MAIN*(except KV-DR29M81)

High-deviation mode

AUTO*(except KV-DR29M81)

Child lock

OFF*

Wide mode

OFF

Game mode

OFF

Teletext mode

OFF(KV-DR29M81)

Sleep timer

OFF

Wake-up timer

OFF

Sound muting

OFF

3DNR

OFF

*= only when in RF mode

– 11 –

• The following adjustments should be made when a complete

realignment is required or a new picture tube is installed.

• These adjustments should be performed with rated power

supply voltage unless otherwise noted.

Controls and switches should be set as follows unless otherwise
noted:
PICTURE control ...........................................................  normal
BRIGHTNESS control ...................................................  normal

Perform the adjustments in the following order :

1. Beam Landing
2. Convergence
3. Focus
4. White Balance
Note :  Test Equipment Required.

1. Color-bar/Pattern Generator
2. Degausser
3. Oscilloscope

normal

Neck assy

G2

G1

G3

Align the edge of 
the neck assy with 
the edge of the G3 grid. 

(KV-DR34)

(KV-DR29)

Neck assy

G2

G1

G3

Align the edge of
the neck assy with
the edge of the G2 grid.

Red

Blue

Green

Preparation :
• In order to reduce the influence of geomagnetism on the set's

picture tube, face it east or west.

• Switch on the set's power and degauss with the degausser.

1. Input a white signal with the pattern generator.

Contrast
Brightness

2. Position neck assy as shown in Fig 5-1.
3. Set the pattern generator raster signal to a green raster.
4. Move the deflection yoke to the rear and adjust with the

purity control so that the green is at the center and the blue
and the red take up equally sized areas on each side.
(See Figures 5-1 through 5-3.)

5. Move the deflection yoke forward and adjust so that the

entire screen is green. (See Figure 5-2.)

6. Switch the raster signal to blue, then to red and verify the

condition.

7. When the position of the deflection yoke has been decided,

fasten the deflection yoke with the screws and DY spacers.

8. If the beam does not land correctly in all the corners, use a

magnet to adjust it.
(See Figure 5-4.)

Purity control
corrects this area.

Disk magnets or rotatable
disk magnets correct these
areas (a-d).

Deflection yoke positioning
corrects these areas.

a

b

b

c

c

d

d

a

}

– 12 –

Preparation :
•

Before starting this adjustment, adjust the focus, horizontal
size and vertical size.

•

Receive cross hatch/dot pattern and set picture mode to
"STANDARD".

1. (Moving horizontally), adjust the H.STAT control so that the

red, green and blue dots are on top of each other at the center
of the screen.

2. (Moving vertically), adjust the V.STAT magnet so that the

red, green and blue dots are on top of each other at the center
of the screen.

3. Adjust Horizontal Trapezoid with “GEO 11 HTR” in Service

Mode to make H-Trapezoid distortion best.

4. If the H.STAT variable resistor cannot bring the red, green

and blue dots together at the center of the screen, adjust the
horizontal convergence with the H.STAT variable resistor and
the V.STAT magnet in the manner given below.
(In this case, the H.STAT variable resistor and the V.STAT
magnet influence each other, so be sure to perform
adjustments while tracking.)

1

V. STAT

2

H. STAT VR

Center dot

R    G    B

R

G

B

H. STAT VR

V. STAT

Magnet

RV702

H. STAT

Y magnet

C Board

R

R

G

G

B

B

a

a

b

b

b

R

R

G

G

B

B

a

b

3

R

R

G

G

B

B

a

a

b

b

b

V.STAT

Purity

BMC (Hexapole)