DOWNLOAD Sony KV-AR34M86 Service Manual ↓ Size: 9.33 MB | Pages: 89 in PDF or view online for FREE

– 9 –

5 Four connectors

7 Two Hooks

2 One Hooks

6 A Board

6 B8 Board

1 One screw (Washer Head) 

(+BVTP 3 x 12)

3 Three screws 
     (Washer head) 
     (+BVTP 3 x 12)

4 One screw 

(Washer head) 

     (+BVTP 3 x 12)  

6 H2 Board

5 Cover, H

4 Two Hooks

2 Five hooks

3 H1 Board

1 Two screws (Washer head)
     (+BVTP 3 x12)

qs

 Earth Coating Assy

!∞ Block Center

4 Anode Cap Removal

!£ Band, DGC Removal

!§ Degaussing Coil

5 C6 Board Removal

9 Chassis Assy Removal

7 VM1 Board Removal

0 Support, CRT(2) Removal

qa

 Spring Tension(2) Removal

!¢ Holder, DGC(2) Removal

!¶ Nut, Special, CRT (4)

6 Loosen the Neck Assembly

fixing screw and removal

8 Loosen the Deflection Yoke

fixing screw and remove

•

Please make sure the TV set is not in standing position before removing necessary CRT support located on bottom
right and left.

1) Place the TV set with the CRT face down on a cushion jig.
2) Removal the rear cover.
3) Unplug all interconnecting leads from the Deflection yoke, Neck assy, Degaussing Coil and CRT grounding strap.

– 10 –

• After removing the anode, short circuit the anode of the picture tube and the anode cap to the metal chassis, CRT

shield or carbon paint on the CRT.

• REMOVING PROCEDURES

1 Turn up one side of the rubber cap in the direction

a.

2 Using a thumb pull up the rubber cap firmly in the direc-

b.

3 When one side of the rubber cap is separated from the

c.

• HOW TO HANDLE AN ANODE-CAP

1 Do not damage the surface of anode-caps with

2 Do not press the rubber too hard so as not to

3 Do not turn the foot of rubber over too hard.

a

a

b

b

c

anode button

– 11 –

If a customer faces some setting problem that cannot be solved, using the "RESET" function some items will
be reset to its original setting (shipment condition)

The way to access to the "RESET" Function:-

a) By pressing "MENU" button or "SELECT" button (for non-menu models) on the Front Key Input and

hold it down for 5 seconds.

Sequential to the resetting operation (either methods being used in No. 2), TV set would shut down once and
automatically turn on again. The power-off duration is expected to be about 500msec. An OSD message,
"RESET" tentatively will be displayed for 10 sec after IK status gets stable.
As a result, some items will be reset to an initial condition (shipment condition) wheareas some other remains
at the last selection by user.

Items that remains at the last selection by user

Reset Items

Channel No., Favourite CH Setup,

PIC rotation, OSD Language, Fine tuning, TV System, Skip

*= only when in RF mode

Video input

RF

Volume

30

Picture mode

DYNAMIC

DTE

ON

Sound mode

DYNAMIC

Surround mode

OFF

Favourite CH mode

AUTO

Multi Picture (PIP)

OFF

PIP position

Bottom Right

OSD recall

OFF

Antenna sensitivity

OFF

Antenna sensitivity

HIGH*

Stereo mode

STEREO

Bilingual mode

MAIN*

High-deviation mode

AUTO

Child lock

OFF*

Wide mode

OFF

Game mode

OFF

Sleep timer

OFF

Wake-up timer

OFF

Sound muting

OFF

– 12 –

• The following adjustments should be made when a complete

realignment is required or a new picture tube is installed.

• These adjustments should be performed with rated power

supply voltage unless otherwise noted.

Controls and switches should be set as follows unless otherwise noted:

PICTURE control ...........................................................  normal

BRIGHTNESS control ...................................................  normal

Perform the adjustments in the following order :

1. Beam Landing

2. Convergence

3. Focus

4. White Balance

Note :  Test Equipment Required.

1. Pattern Generator

2. Degausser

3. Oscilloscope

normal

Preparation :
• In order to reduce the influence of geomagnetism on the set's

picture tube, face it east or west.

• Switch on the set's power and degauss with the degausser.

1. Input a white signal with the pattern generator.

Contrast
Brightness

2. Position neck assy as shown in Fig3-2.
3. Set the pattern generator raster signal to a green raster.
4. Move the deflection yoke to the rear and adjust with the

purity control so that the green is at the center and the blue
and the red take up equally sized areas on each side.
(See Figures 3-1 through 3-4.)

5. Move the deflection yoke forward and adjust so that the

entire screen is green. (See Figure 3-2.)

6. Switch the raster signal to blue, then to red and verify the

condition.

7. When the position of the deflection yoke has been decided,

fasten the deflection yoke with the screws and DY spacers.

8. If the beam does not land correctly in all the corners, use a

magnet to adjust it.

(See Figure 3-5.)

}

G2

G1

G3

a

b

b

c

c

d

d

a

Purity control
corrects this area.

Disk magnets or rotatable
disk magnets correct these
areas (a-d).

Deflection yoke positioning
corrects these areas.

Neck Assy

Behind the G3 edge

○

○

○

○

○

○

○

○

○

○

○

○

○

○

○

○

○

○

○

○

○

○

○

○

○

○

○

○

○

○

○

○

○

○

○

○

○

○

○

○

○

○

○

○

○

○

○

○

○

○

○

○

○

○

○

○

○

○

○

○

○

○

○

Red

Blue

Green

Purity control