DOWNLOAD Sony KV-AR34M86 Service Manual ↓ Size: 9.33 MB | Pages: 89 in PDF or view online for FREE

– 5 –

Turn off the power switch on the TV main unit or unplug the power cord from the outlet to stop the STANDBY/TIMER lamp
from flashing.

For errors with symptoms such as “power sometimes shuts off” or “screen sometimes goes out” that cannot be confirmed, it
is possible to bring up past occurances of failure for confirmation on the screen:

[To Bring Up Screen Test]
In standby mode, press buttons on the remote commander sequentially in rapid succession as shown below:

[Screen display] / channel [5] / Sound volume [-] / Power ON

˘

Note that this differs from entering the service mode (mode volume  [+]).

Diagnostic Item

Flash Count*

+B overcurrent/overvoltage

2 times

Vertical deflection stopped

White balance failure

5 times

* One flash count is not used for self-diagnostic.

2 times

5 times

Lamp ON 0.3 sec.

Lamp OFF 0.3 sec.

Lamp OFF 3 sec.

002 : 000
003 : 000
004 : 000
005 : 001

101 : 000

SELF DIAGNOSTIC

Numeral "0" means that no fault has been detected.

Numeral "1" means a fault has been detected.

STANDBY/SLEEP lamp

– 6 –

Since the diagnostic results displayed on the screen are not automatically cleared, always check the self-diagnostic screen
during repairs. When you have completed the repairs, clear the result display to “0”.

Unless the result display is cleared to “0”, the self-diagnostic function will not be able to detect subsequent faults after
completion of the repairs.

[Clearing the result display]
To clear the result display to “0”, press buttons on the remote commander sequentially as shown below when the diagnostic
screen is being displayed.

Channel [8]

/ 0

[Quitting Self-diagnostic screen]
To quit the entire self-diagnostic screen, turn off the power switch on the remote commander or the main unit.

[+B overcurrent ªOCPº]

Occurs when an overcurrent on the +B(135) line is detected by Q604. If Q604 go to ON
and the voltage to pin 18 of IC301 should go down when V.SYNC is more than seven
verticals in a period, the unit will automatically turn off.

[Vertical deflection stopped]

Occurs when an absence of the vertical deflection pulse is detected by Q509 and IC001
shut down the power supply.

[Vertical deflection overcurrent]

Occurs when an overcurrent on V drive line is detected by Q507. Power supply will be
shut down when detect this by IC001.

[White balance failure]

If the RGB levels* do not balance or become low level within 5 seconds, this error will be
detected by IC301. TV will stay on, but there will be no picture.

* (Refers to the RGB levels of the AKB detection Ref pulse that detects IK.)

IC301

Y/CHROMA JUNGLE

FROM

CRT

[V] Q509/507

IC001

SYSTEM

IC003

MEMORY

IK-IN

MP/
PROTECT

O-LED

IO-8DAT

B-DAT

IO-SDAT

5

21

18

51

46

SDA 35

FROM
[+B] Q604 C6

45

– 7 –

1 Thirteen screws
     (+BVTP 4 

× 16)

2 Rear cover

1 Two screws (+BVTP 3x12)

4 F Board

2 F Board bracket

3 Two hooks

3 DH Board
     (Not used for this model)

7 HV Cap block

2 PWB holder

5 Two screws 
     (+BVTP 3x12)

1 Two screws 
     (+BVTP 3x12)

4 One Hook

6 One screw 
     (+BVTP 4x16)

8 Bracket HVC

3 Two screws
     (+BVTP 4 

× 16)

1 Two screws
     (+BVTP 4 

× 16)

2 Two screws
     (Washer Head)
     (+P4x16)

– 8 –

2 V1 Board

1 Two connectors

6 Two Hooks

3 One screw
     (+BVTP 4 

× 16)

2 One screw
     (+BVTP 3 

× 12)

1 One screw
     (+BVTP 3 

× 12)

4 Two screws
     (+BVTP 3 

× 12)

5 J Board

7 Terminal bracket

2 D2 Board

1 One Hooks

1 P5 Board

2 Two screws

     (+BVTP 3x12)

• Firstly, please make sure the shield case with two screws (+BVTP 3 x 12) is remove.