DOWNLOAD Sony KV-AR21M83 Service Manual ↓ Size: 5.65 MB | Pages: 97 in PDF or view online for FREE

– 10 –

Preparation:
• Before starting this adjustment, adjust the horizontal

static convergence and the vertical static
convergence

TLV

R B

YCH

R

B

XCV

B

R

TLH

B

R

Piece A (90), conv. correct

a

b

c

d

TLH

Insert

TLH

Correction Plate to DY Pocket

(Left or Right)

YCH

Insert

YCH

VOL on DY

TLV

Rotate TLV

VOL on DY

XCV

Rotate XCV

Adj core on DY

1. Affix a Piece A (90), conv. correct corresponding to

the misconverged areas.

b

a

c

d

a-d : screen-corner
        misconvergence

ON DY:

TLV

TLV

XCV

YCH

DY pocket

DY pocket

TLH Plate

XCV

– 11 –

1. Set to Service Mode (Refer Section 3-1:

ADJUSTMENTS WITH COMMANDER)

2. Input white raster signal.
3. Set Picture to <DYNAMIC mode>
4. Select RDRV (02) with 

1

 and 

4

 and fixed the value

to 25 with 

3

 and 

6

.

5. Adjust WHBL GDRV (03) and BDRV (04) with 

1

 and

4

 and adjust the data with 

3

 and 

6

 for best white

balance in Highlight condition.

6. Write into the memory by pressing [MUTING] then 

-

.

7. Adjust WHBL BKOR (00) and BKOG (01) with 

1

 and

4

 and adjust the level with 

3

 and 

6

 for best white

balance cut-off condition.

8. Write into memory by pressing [MUTING] then 

-

.

9. US model need to apply only for colour temperature

in Neutral.

1. Set to service mode.
2. Brightness set to 50%, Picture....Minimum
3. Select WHBL SBRT (10) with 

1

 and 

4

 and adjust

SBRT (10) data with 

3

 and 

6

 so that the third stripe

from right dimly lit.

4. Write into the memory by pressing [MUTING] then 

-

.

5. GA models C/O: 20 IRE

S/G: 30 IRE

165 

± 2VDC

FOCUS adjustment should be completed before the W/B
adjustment:
1. Receive digital monoscope pattern.
2. Set picture mode: DYNAMIC.
3. Adjust focus VR to obtain a just focus at the center of

the screen.

4. Change receiving signal to white pattern and blue

back.

5. Confirm MAGENTA RING is not noticeable. Incase

magenta ring is obvious, then adjust FOCUS VR to
balance magenta ring and FOCUS.

1. Set the PICTURE & BRIGHTNESS to STANDARD.
2. Put the Video input mode signal.
3. Connect R,G,B of the CV board cathode to

oscilloscope.

4. Adjust Brightness to obtain the cathode value to

value below.

5. Adjust G2 (screen) on the FBT until picture shows

the point before cut off.

SCREEN

FOCUS

– 12 –

Service adjustments to this model can be performed using the supplied remote commander RM-W101.

a. ENTERING SERVICE MODE
With the unit on standby

This operation sequence puts the unit into service mode.
This screen display is:

b. METHOD OF CANCELLATION FROM SERVICE MODE
Set the standby condition (Press [POWER] button on the commander), then press [POWER] button again, hereupon it
becomes TV mode.

c. METHOD OF WRITE INTO MEMORY
1. Set to Service Mode.
2. Press 

1

 (UP) and 

4

 (DOWN), to select the adjustment item.

3. Change item by pressing 

3

, 

6

.

4. Press [MUTING] button to indicate WRITE on the screen.
5. Press 

-

 button to write into memory.

d. MEMORY WRITE CONFIRMATION METHOD
1. After adjustment, pull out the plug from AC outlet, and then plug into AC outlet again.
2. Turn the power switch ON and set to Service Mode.
3. Call the adjusted items again to confirm adjustments were made.

  

t [DISPLAY] t 5 t [VOL $+% ] t [POWER]

item no.

service data

NVM

field

channel no./

category

in decimal

item name

in decimal

NG

service command

frequency

video input name

GEOM

006

HSIZ

031

x

SERVICE

60

S VIDEO 1

software

service data

reserved

power on time

release ID

version

in binary

for factory

color system

(decimal?)

SUS01

0.69U

0001 1111

FF FF

NTSC3

65535

Status Byte

Status Byte

Flash DCXO

#1 SSD

#2 SSD

111 11 11 1 7 11

FG

xy 111

000000

000000

VDSP_C Flag

CO_LOCKED

VDSP

Detected Stereo Type (Direct Value from CZ_ Stereo_Mode)

S : for Sony
A : Aiwa

U S

: US/Latin/Taiwan

E U

: Europe

G A

: General Area

J P

: Japan

0 1 : serial no. of the M/P release

for each destination

111

Needed for Nicam DCXO aligment Purpose

xy

Value of x = 0 - Unknown, 1 - BTSC, 2 - A2, 3 - NICAM,
4 - KOREAN, 5 - Japan, 6 - AV Stereo
Value of y = 0 - Mono, 1 - Stereo, 2 - Bilingual, 4 - SAP/Single

1, 4

Select the adjustment item.

r

3, 6

Raise/lower the data value.

r

[MUTING]

Writes.

r

-

Executes the writing.

– 13 –

7, -

All the data becomes the values in memory.

8, -

All user control goes to the standard state.

Display, -

Service data initialization (Be sure not to use usually.)

2, 5

Select Device or Category

Item Number 000 HPOS
This explanation uses H POSITION as an example.
1. Select "000 HPOS" with the 

1

 and 

4

 buttons, or 

2

 and 

5

.

2. Raise/lower the data with the 

3

 and 

6

 buttons.

3. Select the optimum state. (The standard is IF for PAL reception.)
4. Write with the [MUTING] button. (The display changes to WRITE.)
5. Execute the writing with the 

-

 button. (The WRITE display will be changed to red color while excuting, and back to

SERVICE.)

Example on screen display :-

Use the same method for all Items. Use 

1

 and 

4

 to select the adjustment item, use 

3

 and 

6

 to adjust, write with

[MUTING], then execute the write with 

-

.

Note : 1. In [WRITE], the data for all items are written into memory together.

2. For adjustment items that have different standard data between 50Hz or 60Hz, be sure to use the respective

input signal after adjustment.

Adjusted with [3] and [6] buttons.

GREEN

GEOM

000

HPOS

039

SERVICE

50

VIDEO 1

write with [MUTING].

GREEN

GEOM

000

HPOS

039

WRITE

50

VIDEO

1

GEOM

000

HPOS

039

WRITE

50

VIDEO

1

Write executed with [0].

RED

The WRITE display
then returns to green
SERVICE