Sony KV-32HS20 Service Manual ▷ View online
KV-32HS20/36HS20/36HS20H/32XBR450/36XBR450/36XBR450H
— 21 —
Control Register
Function & Link
Data
Type
Data
Range
Comment
Standard
Non-standard
Standard
Non-standard
0
NRMD Operation mode setting
0~3
0
1
3
3
1
YAPS
Y-output correction
(V-aperture compensation & Y-peaking filtering)
(V-aperture compensation & Y-peaking filtering)
C
0~3
3
2
CLKS System clock setting
C
0~3
1
Standard
Non-standard
Standard
Non-standard
3
NSDS Selection for standard/non-satndard signal processing
0~3
0
0
0
0
4
MSS
Selection for inter-frame/inter-line processing
C
0~3
0
5
KILS
Killer processing selection
C
0~3
1
6
CDL
C-signal phase with respect to the Y-signal
(Fine adjustment at 70 ns/step)
(Fine adjustment at 70 ns/step)
C
0~7
3
NRMD Setting-based Control Table for DYCO, DYGA, DCCO, DCGA
NRMD = 0
NRMD = 1
NRMD = 2
NRMD = 3
7
DYCO DY detection coring level (Y motion detection coring)
0~15
2
2
2
2
8
DYGA DY detection gain (Y motion detection gain)
0~15
10
10
10
10
9
DCCO DC detection coring level (C motion detection coring)
0~15
5
5
5
5
10 DCGA DC detection gain (C motion detection gain)
0~15
5
5
5
5
11 YNRL Frame recersive YNR nonlinear filter limit level
C
0~3
1
12 CNRL Frame recersive CNR nonlinear filter limit level
C
0~3
1
UHF/VHF
Video1~4
Video5&6
13 VTRH
Hysteresis for Hsync non-standard signal detection
(out-of-Hsync intra-field)
(out-of-Hsync intra-field)
0~3
1
1
1
14 VTRR
Sensitivity for Hsync non-standard signal detection
(out-of-Hsync intra-field)
(out-of-Hsync intra-field)
0~3
1
1
1
15 LDSR
Sensitivity for frame non-standard signal detection
(out-of-Hsync inter-frame)
(out-of-Hsync inter-frame)
0~3
2
2
2
VM = Off
VM = Low
VM = Mid
VM = High
16 VAPG V-aperture compensation gain
0~7
0
2
3
4
17
VAPI
V-aperture compensation convergence point
0~31
4
4
4
SNNR = 0
SNNR = 1
SNNR = 2
SNNR = 3
18
YPFT
Y peaking filter (BPF) center frequency
0~3
0
0
0
0
0
19 YPFG Y peaking filter (BPF) gain
0~15
7
0
1
2
3
SNNR Setting-based Control Table for YPFT & YHFG
SNNR Setting (-Offset)
4
(32V)
or 8
(36V)
{Initial/CBA Data = 8}
VM&SNNR Setting-based Control Table for VAPG & VAPI
VAPG= VAPG1 - VAPG2
VAPG= VAPG1 - VAPG2
Data Initial/Average Setting
(32V&36V CRTs)
Register
No & Name
SVideo
UHF/VHF & CVideo
CVideo (CV): CVideo1~4 inputs
SVideo (SV): SVideo1~3 inputs
SVideo (SV): SVideo1~3 inputs
C: Common data
Video1~4: CVideo1~4 & SVideo1~3 inputs
Video5&6: YPbPr-480i/480p/1080i inputs
Video5&6: YPbPr-480i/480p/1080i inputs
VAPG1 Data Based on MENU/VM Setting
SVideo
UHF/VHF & CVideo
DX1A-2001&2000 SERVICE LIST (#1):
3D-COMB / mPD64082
(Part-1/4)
Device Name:
m
PD64082GF { 3D-Comb Filter / NEC } / IC3501 (BC-board) / P/N: 8-759-594-44 (SB#: V7372)
Slave Address: B8h (Write Address) / B9h (Read Address)
This setting continues to
the next page.
Note: The same 3D-COMB service data is used for DX1A-2001&2000.
Register
No & Name
SNNR = 0
SNNR = 1
SNNR = 2
SNNR = 3
#16 VAPG (cont.
0
0
0
0
Note: The same 3D-COMB service data is used for DX1A-2001&2000.
VAPG2 Data Based on SNNR/Offset-setting
Data Initial/Average Setting
(32V&36V CRTs)
Comment
DX1A-2001&2000 SERVICE LIST (#1):
3D-COMB / mPD64082
(Part-2/4)
KV-32HS20/36HS20/36HS20H/32XBR450/36XBR450/36XBR450H
— 22 —
Control Register
Function & Link
Data
Type
Data
Range
Comment
SNNR Setting-based Control Table for YHCO & YHCG
SNNR = 0
SNNR = 1
SNNR = 2
SNNR = 3
(Not SNNR Offset Data)
20 YHCO Y output high frequency component coring
0~3
1
1
1
1
21 YHCG Y output high frequency component coring gain
0, 1
0
0
0
0
22
HSSL Hsync slice level
C
0~15
12
23
VSSL Vsync slice level
C
0~15
8
24 ADCL ADC clock delay
C
0~3
3
NRMD Setting-based Control Table for D2GA
NRMD = 0
NRMD = 1
NRMD = 2
NRMD = 3
25 D2GA Moving detection gain
0~7
4
4
4
4
26
KILR
Killer detection reference
C
0~15
3
27
OP1
Option1:
Selection of comb filter & recursive noise reduction types
Selection of comb filter & recursive noise reduction types
C
0, 1
1
UHF/VHF
CVideo1
SVideo1
28
NR1
Noise reduction on/off
0, 1
0
0
1
29
NR2
SNNR control on/off
C
0, 1
0
30
WSL
Noise level detection data
0~255
31
HPLL
H-PLL filter (Must be set to 1 when MN signal is input.)
C
0, 1
1
32
BPLL
Burst PLL filter
C
0, 1
1
33
FSCF
Burst extraction gain
C
0, 1
0
34
PLLF
PLL loop gain
C
0, 1
1
UHF/VHF
Video1~4
Video5&6
35 CC3N Selection of a line-comb filter C separation filter characteristic
0, 1
0
0
0
36
HDP
Fine adjustment of the system H-phase
C
0~7
5
37 BGPS
Internal burst gate start position
{Gate Start Position from Hsync center = 0.25 x BGPS + 2
{Gate Start Position from Hsync center = 0.25 x BGPS + 2
C
0~15
4
38 BGPW
Internal burst gate width
{Gate Width = 0.25 x BGPW + 0.5 (ms)}
{Gate Width = 0.25 x BGPW + 0.5 (ms)}
C
0~15
10
39
TEST
Test bit {0: Normal mode, 1: Test mode (forbidden setting)}
C
0, 1
0
40
WSC
Amount of noise detection coring
C
0~3
1
Video5&6
41
LIND
DRC-M line-doubling setting for non-standard signals
Micro
0~63
2
42 PFGO (YPFG offset at GR on) --- Not used for DX1A
---
0~7
3
1 Byte Data from Read Register WSL
C: Common data
Register
No. & Name
This setting is used for non-standard signals
such as Play Station signals.
such as Play Station signals.
Note: The same 3D-COMB service data is used for DX1A-2001&2000.
(Not used for DX1A)
UHF/VHF & Video1~4
0
Data Initial/Average Setting
(32V&36V CRTs)
This setting continues to
the next page.
Video1~4: CVideo1~4 & SVideo1~3 inputs
Video5&6: YPbPr-480i/480p/1080i inputs
Video5&6: YPbPr-480i/480p/1080i inputs
YHCO&YHCG settings are sent
directly to 3D-Comb device.
directly to 3D-Comb device.
DX1A-2001&2000 SERVICE LIST (#1):
3D-COMB / mPD64082
(Part-3/4)
Register
No & Name
CVideo2
SVideo2
CVideo3
SVideo3
#28 NR1 (cont.)
0
1
0
1
Note: The same 3D-COMB service data is used for DX1A-2001&2000.
Data Initial/Average Setting
(32V&36V CRTs)
Comment
DX1A-2001&2000 SERVICE LIST (#1):
3D-COMB / mPD64082
(Part-4/4)
KV-32HS20/36HS20/36HS20H/32XBR450/36XBR450/36XBR450H
— 23 —
Control Register
Function & Link
Data
Type
Data
Range
Note
P&P-Left
(M)-DRC
P&P-Left
(M)-1080i
P&P-Left
(M)-DRC
P&P-Left
(M)-480i
0
YLEV
Y-Out gain
0~63
23
27*
28
31*
1
CLEV
Cb&Cr-Out gains
0~63
17
55*
32
31*
2
SCON Sub contrast
Adj.
0~15
3
SCOL
Sub color
Adj.
0~15
4
SHUE
Sub hue
Adj.
0~15
5
YDLY
Y/C delay time
0~3
SNNR Data-related Settings
UHF/VHF
CVideo
SVideo
YPbPr
480i
SNNR=0
(-offset)
SNNR=1
(-offset)
SNNR=2
(-offset)
SNNR=3
(-offset)
6
SHAP
Sharpness
0~15
6
4
4
4
0
1
2
3
7
SHF0
Sharpness f0 selector
0~3
0
0
0
0
8
PREO Sharpness pre/over-shoot ratio
0~3
3
0
0
0
9
BPF0
Chroma band filter f0 setting
0~3
3
0
0
0
10
BPFQ
Chroma band filter Q setting
0~3
0
3
3
3
11 BPSW Chroma band filter on/off
0, 1
1
0
0
0
12
TRAP
Y bolck chroma trap filter on/off
0, 1
0
0
0
0
13
LPF
YPbPr-Output LPF on/off
0, 1
0
0
0
0
UHF/VHF
Video
YPbPr
480i
14
AFCG AFC Loop Gain (PLL between Hsync & HVCO)
0, 1
1
0
0
15 CDMD V countdown system mode selector
0~3
3
3
3
16
SSMD H&Vsync slide level setting
0~3
0
0
0
17
HMSK Masking of macrovision signal on/off
0, 1
1
1
1
18
HALI
H automatic adjustment on/off
0, 1
0
0
0
19
PPHA
H TIM phase adjustment for video
0~15
7
7
7
P&P-Left
(M)-DRC
P&P-Left
(M)-1080i
P&P-Left
(M)-DRC
P&P-Left
(M)-480i
Cb-Offset1 of Cb IN (Pin34)
Cb-Offset2 of EXT Cb (Pin38)
Cr-Offset1 of Cr IN (Pin35)
Cr-Offset2 of EXT Cr (Pin39)
Cb-Offset2 of EXT Cb (Pin38)
Cr-Offset1 of Cr IN (Pin35)
Cr-Offset2 of EXT Cr (Pin39)
Single
UBLK = 0
UBLK = 1
UBLK = 2
UBLK = 3
UBLK = 4
UBLK = 5UBLK = 6
UBLK = 7
UBLK = 0~7
22
ATPD
Auto-pedestal Inflection Point
0~3
0
1
2
3
1
2
3
2
0
23
DCTR
DC Transmission Ratio
0~3
0
1
1
1
2
2
2
3
0
Adj.: Adjusted data
[Adj.-2steps]: The adjusted data - 2 steps
[Adj.-2steps]: The adjusted data - 2 steps
CVideo: CVideo1~4 Inputs
SVideo: SVideo1~3 Inputs
SVideo: SVideo1~3 Inputs
*: Settings not used
(31): The center setting = 31
(31): The center setting = 31
UHF/VHF
7 [7]
31*
31
31*
31
CXA2150P-4/#13 UBLK Setting-related Controls for ATPD & DCTR
31*
7 [7]
Data Initial/Average Setting
(32V&36V CRTs)
Video: CVideo1~4 & SVideo1~3 Inputs
P&P-Left (M)-1080i&480i: If P&P-Left is
1080i/480p signal, the signal from the main
chroma decoder is sent to MID/VDO input.
*: Settings not used
P&P-Left (M)-1080i&480i: If P&P-Left is
1080i/480p signal, the signal from the main
chroma decoder is sent to MID/VDO input.
*: Settings not used
31*
0~(31)~63
YPbPr-480i
UHF/VHF & Video
7 [Adj.-2steps]
UHF/VHF & Video
0
Video
7 [7]
7 [7]
7 [7]
7 [Adj.-2steps]
0
P&P & Favorite
CBOF
31
31
CROF
0~(31)~63
YPbPr-480i
P&P & Favorite
Note: The same CXA2103 service data (Main&Sub) is used for DX1A-2001&2000.
20
21
Register
No & Name
Data Initial Setting & [Average Data]
(32V&36V CRTs)
DX1A-2001&2000 SERVICE LIST (#2-1):
CXA2103-1 {Main}
Device Name: CXA2103Q { NTSC-YCT (Chroma Decoder) / SONY } / IC3048 (B-board) / P/N: 8-752-089-50 (SBorSD#: NA)
Slave Address: 9Ah { Main }
Slave Address: 9Ah { Main }
KV-32HS20/36HS20/36HS20H/32XBR450/36XBR450/36XBR450H
— 24 —
Control Register
Function & Link
Data
Type
Data
Range
Note
P&P-Right
(S)
P&P-Right
(S)-DRC
0
YLEV
Y-Out gain
0~63
23
22
1
CLEV
Cb&Cr-Out gains
0~63
18
16
2
SCON Sub contrast
Adj.
0~15
3
SCOL
Sub color
Adj.
0~15
4
SHUE
Sub hue
Adj.
0~15
5
YDLY
Y/C delay time
0~3
SNNR Data-related Settings
UHF/VHF
CVideo
SVideo
SNNR=0
(-offset)
SNNR=1
(-offset)
SNNR=2
(-offset)
SNNR=3
(-offset)
6
SHAP
Sharpness
0~15
6
4
4
0
1
2
3
7
SHF0
Sharpness f0 selector
0~3
0
0
0
8
PREO Sharpness pre/over-shoot ratio
0~3
3
0
0
9
BPF0
Chroma band filter f0 setting
0~3
0
0
0
10
BPFQ
Chroma band filter Q setting
0~3
0
0
0
11 BPSW Chroma band filter on/off
0, 1
0
0
0
12
TRAP
Y bolck chroma trap filter on/off
0, 1
0
0
0
13
LPF
YPbPr-Output LPF on/off
0, 1
0
0
0
UHF/VHF
Video
14
AFCG AFC Loop Gain
0, 1
1
0
15 CDMD V countdown system mode selector
0~3
3
3
16
SSMD H&Vsync slide level setting
0~3
0
0
17
HMSK Masking of macrovision signal on/off
0, 1
1
1
18
HALI
H automatic adjustment on/off
0, 1
0
0
19
PPHA
H TIM phase adjustment for video
0~15
7
7
P&P-Right
(S)
P&P-Right
(S)-DRC
P&P-Right
(S)
P&P-Right
(S)-DRC
Cb-Offset1 of Cb IN (Pin34)
Cb-Offset2 of EXT Cb (Pin38)
Cr-Offset1 of Cr IN (Pin35)
Cr-Offset2 of EXT Cr (Pin39)
Cb-Offset2 of EXT Cb (Pin38)
Cr-Offset1 of Cr IN (Pin35)
Cr-Offset2 of EXT Cr (Pin39)
Single
UBLK = 0
UBLK = 1
UBLK = 2
UBLK = 3
UBLK = 4
UBLK = 5UBLK = 6
UBLK = 7
UBLK = 0~7
22
ATPD
Auto-pedestal Inflection Point
0~3
0
1
2
3
1
2
3
2
0
23
DCTR
DC Transmission Ratio
0~3
0
1
1
1
2
2
2
3
0
Note: The same CXA2103 service data (Main&Sub) is used for DX1A-2001&2000.
0
0
7 [7]
7 [7]
UHF/VHF
Video
7 [7]
Data Initial/Average Setting
(32V&36V CRTs)
Device Name: CXA2103Q { NTSC-YCT (Chroma Decoder) / SONY } / IC3110 (B-board) / P/N: 8-752-089-50 (SBorSD#: NA)
Slave Address: 9Eh { Sub }
Slave Address: 9Eh { Sub }
Register
No & Name
DX1A-2001&2000 SERVICE LIST (#2-2):
CXA2103-2 {Sub}
7 [7]
31*
31*
UHF/VHF & CVideo
31*
31
0~(31)~63
31
31
21
CROF
0~(31)~63
YPbPr-480i
31*
CBOF
UHF/VHF & Video
Data Initial Setting & [Average Data]
(32V&36V CRTs)
P&P & Favorite
P&P & Favorite
20
7 [Adj.-2steps]
7 [Adj.-2steps]
Adj.: Adjusted data
[Adj.-2steps]: The adjusted data - 2 steps
[Adj.-2steps]: The adjusted data - 2 steps
*: Settings not used
(31): The center setting = 31
(31): The center setting = 31
CVideo: CVideo1~4 Inputs
SVideo: SVideo1~3 Inputs
SVideo: SVideo1~3 Inputs
31
Video: CVideo1~4 & SVideo1~3 Inputs
P&P-Right (S)-DRC: If P&P-Left is 1080i/
480p signal, the signal from the sub chroma
decoder is switched to DRC path.
P&P-Right (S)-DRC: If P&P-Left is 1080i/
480p signal, the signal from the sub chroma
decoder is switched to DRC path.
CXA2150P-4/#13 UBLK Setting-related Controls for ATPD & DCTR
Click on the first or last page to see other KV-32HS20 service manuals if exist.