Sony KV-21HFV100 (serv.man2) Service Manual ▷ View online
– 29 –
KV-21HFV100
RM-W112
No. OPB6
GA US
(US Model Destination)
0 = US/CANADA/Latin
1 = Taiwan/Korea/Philippine
(Wake-up timer enable);
(GA Surround Spec:OFF,
SIMULATED, SRS)
1 = Taiwan/Korea/Philippine
(Wake-up timer enable);
(GA Surround Spec:OFF,
SIMULATED, SRS)
3D OSD
(BX1L Full version GA Multi
0 = Normal with 3D Intelligent picture OSD
Destination ONLY)
1 = Disable 3D Intelligent picture OSD
Feature 2
(Temporary for BX1L)
0 = Comb Not available
1 = Comb available
1 = Comb available
Feature 1
(Temporary for BX1L)
0 = PiP Not Available
1 = PiP available
1 = PiP available
OSD Language Selection
US (GA NTSC)
1x1x = Complicated Chinese
1xx1 = Korean (note: for BX1L, combination of
1xx1 = Korean (note: for BX1L, combination of
C.Chinese & Korean not available)
GA
1xxx = Simplified Chinese
x1xx = Arabic/Russian
xx1x = Thai
xxx1 = Vietnamese
x1xx = Arabic/Russian
xx1x = Thai
xxx1 = Vietnamese
Full Surround
(Full Surround option-no for
0 = Normal Surround Model
EURO model)
1 = Full Surround Model
(Off/simulated/surround/
SRS/WOW/TruSurround)
SRS/WOW/TruSurround)
No Surround
(No Surround Model)
0 = Surround Model, 1 = Non-Surround Model
Cosmic ASD
Automatic Standard Detection
0 = disabled, 1 = enabled
Using COSMIC (Non-Stereo)
ASD
(Automatic Standard Detection)
0 = disabled, 1 = enabled
Tilt
(Tilt Correction/PIC Rotation)
0 = disabled, 1 = enabled
IP Plus
(Intelligent Picture Plus)
0 = disabled, 1 = enabled
IP
(Intelligent Picture)
0 = disabled, 1 = enabled
Wide
(Wide Mode/V-Compressed)
0 = disabled, 1 = enabled
No. OPB5
Item
Full
No
COSMIC
ASD
Tilt
IP Plus
IP
Wide
DEC
Surround
Surround
ASD
KV-21HFV100
0
0
0
1
1
1
1
1
31
Item
GA US
3D OSD
Feature 2
Feature 1
OSD Language Selection
DEC
KV-21HFV100
1
0
0
0
0
0
0
1
129
– 30 –
KV-21HFV100
RM-W112
3-3.
PICTURE QUALITY ADJUSTMENTS
PMAX/CONTRAST ADJUSTMENT
1. Select Video Mode.
2. Input PAL CB to TV set (others), Input NTSC 75% CB
2. Input PAL CB to TV set (others), Input NTSC 75% CB
to TV set (NTSC model).
3. Set PICT 003 "PWL" to 00h and WHBL 017 "BLBG" to
01h.
4. Set the following condition:
PICTURE 100%, COLOR 0%, BRIGHTNESS 50%.
5. Connect an oscilloscope to pin 4 (R output) of CN004.
6. Set to Service Mode "PWL" to 00h, "BLBG" to 01h.
7. Select SADJ 000 "PMAX" with
6. Set to Service Mode "PWL" to 00h, "BLBG" to 01h.
7. Select SADJ 000 "PMAX" with
1
and
4
of the
commander then adjust VR within spec with
3
and
6
.
8. Select "WIDE" Mode for TV and Video Mode, write
the "PMAX DATA-8 steps" (For models with
V-Compression features only).
V-Compression features only).
9. Then press [MUTING]
t
-
to write the data.
10. Set "PWL" and "BLBG" back to initial data repectively.
(PWL: 01h and BLBG: 00h)
SUB COLOR ADJUSTMENT
1. Select Video and set Picture mode.
2. Input PAL 100% CB to TV set (others), Input NTSC
2. Input PAL 100% CB to TV set (others), Input NTSC
75% CB to TV set (NTSC model).
3. Set PICT 006 "WTS" to 00h, and Intelligent Picture to
"OFF".
4. Set the following condition:
PICTURE 100%, COLOR 50%, BRIGHTNESS 50%,
HUE CENTER, SHP 50%.
HUE CENTER, SHP 50%.
5. Connect an oscilloscope to pin 2 (B output) of CN004.
6. Select to Service Mode and adjust SADJ 004 "SCOL"
6. Select to Service Mode and adjust SADJ 004 "SCOL"
with
1
and
4
of commander then adjust to
VB2 = VB3 = VB4 with
3
and
6
, and write in the
data +5 step offset.
7. Then press [MUTING]
t
-
to write the data.
8. Set "WTS" back to original data, and set Intelligent
Picture to "ON".
SUB HUE ADJUSTMENT
1. Select Video.
2. Input NTSC 3.58 Color Bar to TV set.
3. Set the following condition:
2. Input NTSC 3.58 Color Bar to TV set.
3. Set the following condition:
PICTURE 100%, COLOR 50%, BRIGHTNESS 50%,
HUE Center, SHP 50%.
HUE Center, SHP 50%.
4. Connect an oscilloscope to pin 2 (B output) of CN004.
5. Set to service mode and select SADJ 001 "SHUE"
5. Set to service mode and select SADJ 001 "SHUE"
with
1
and
4
of commander then adjust to
VB1=VB2=VB3=VB4 with
3
and
6
.
6. Then press [MUTING]
t
-
to write the data.
7. Select TV channel and repeat 3-6
(Except GA NTSC model).
8. i. Select TV channel with 3.58 repeat 3-5, +1 step
data offset (applied to GA NTSC models)
ii. Then press [MUTING]
t
-
to write the data.
9. Single systems models with NTSC 4.43 select TV
channel with NTSC 4.43 repeat item 3-6.
The highest level of VB1, VB2, VB3, VB4 must be
aligned at the same time.
The ideal difference between VB2 and VB3 is within
±80mV.
aligned at the same time.
The ideal difference between VB2 and VB3 is within
±80mV.
SUB HUE ADJUSTMENT FOR YUV INPUT
(FOR HW & AR SERIES ONLY)
(FOR HW & AR SERIES ONLY)
1. Select YUV input.
2. Input a NTSC 3.58 Color Bar into YUV mode.
3. Connect an oscilloscope to pin 2 (B output) of CN004.
4. Set the service mode and select YC 013 "TINT" with
2. Input a NTSC 3.58 Color Bar into YUV mode.
3. Connect an oscilloscope to pin 2 (B output) of CN004.
4. Set the service mode and select YC 013 "TINT" with
1
and
4
of the commander then adjust to
VB1=VB2=VB3=VB3 with
3
and
6
.
5. Then press [MUTING]
t
-
to write the data.
The highest level of VB1, VB2, VB3, VB4 must be
aligned at the same time.
The ideal difference between VB2 and VB3 is within
±80mV.
aligned at the same time.
The ideal difference between VB2 and VB3 is within
±80mV.
3-4.
DEFLECTION ADJUSTMENT
H-TRAPEZOID ADJUSTMENT
1. Receive cross hatch/dotsignal.
2. Adjust on to make H-Trapezoid distortion best.
2. Adjust on to make H-Trapezoid distortion best.
NORMAL MODE (50Hz)
1. Set to Service Mode.
2. Input SPCB Signal.
3. Using the
2. Input SPCB Signal.
3. Using the
1
and
4
button select GEOM (Service Mode).
VB2 = VB3 = VB4 (for PAL sub color adjustment)
VB1 = VB4 (for NTSC sub color adjustment)
(Difference is within 70mV)
VB1
VB2 VB3 VB4
VR
Black
1.46
± 0.03 Vp-p = For 21" without VM models/
For 14" GA models
1.65
± 0.03 Vp-p = with VM models except NTSC models
1.23
± 0.03 Vp-p = for NTSC models VM models
1.10
± 0.03 Vp-p = for 21" NTSC non VM models/
For 14" GA NTSC models
VB1
VB2
VB3 VB4
80mV
VB1 = VB2 = VB3 = VB4
VB1
VB2
VB3 VB4
VB1 = VB2 = VB3 = VB4
– 31 –
KV-21HFV100
RM-W112
GEOM :
000
HPOS
Horizontal Shift (HS)
001
HPAR
Horizontal Parallelogram
002
HBOW
Horizontal Bow
003
VLIN
Vertical Linearity
004
VSCR
Vertical Scroll
005
HSIZ
EW Width (EW)
006
EWPW
EW Parabola/Width (PW)
007
UCOP
EW Upper Corner Parabola
008
LCOP
EW Lower Corner Parabola
009
EWTZ
EW Trapezium
010
VSLP
Vertical Slope (VS)
011
VSIZ
Vertical Amplitude
012
SCOR
S-Correction (SC)
013
VPOS
Vertical Shift (VSH)
014
HBL
RGB Blanking Mode
015
WBF
Timing of Wide Blanking (WBF)
016
WBR
Timing of Wide Blanking (WBR)
017
SBL
Service Blanking
018
COPY
Copy the GEOM data to all
50/60Hz NVM area
50/60Hz NVM area
5. Write into memory by pressing [MUTING] then
-
on
the remote commander.
WIDE MODE (50Hz)
(V-Compression Adjustment)
1. Input SPCB signal.
2. Adjust condition change to WIDE MODE : ON
3. Copy (Item from normal mode 50Hz) all Normal
1. Input SPCB signal.
2. Adjust condition change to WIDE MODE : ON
3. Copy (Item from normal mode 50Hz) all Normal
Mode adjusted data.
NORMAL MODE (60Hz)
1. Input 525/60Hz signal.
2. They can copy 50Hz first.
2. They can copy 50Hz first.
("COPY" under GEOM is set to
1
, then [MUTE] +
-
)
3. Using the
1
and
4
button, select category GEOM
(Service Mode).
4. Raise/lower data using the
3
and
6
buttons to
obtain optimum image.
GEOM :
000
HPOS
Horizontal Shift (HS)
001
HPAR
Horizontal Parallelogram
002
HBOW
Horizontal Bow
003
VLIN
Vertical Linearity
004
VSCR
Vertical Scroll
005
HSIZ
EW Width (EW)
006
EWPW
EW Parabola/Width (PW)
007
UCOP
EW Upper Corner Parabola
008
LCOP
EW Lower Corner Parabola
009
EWTZ
EW Trapezium
010
VSLP
Vertical Slope (VS)
011
VSIZ
Vertical Amplitude
012
SCOR
S-Correction (SC)
013
VPOS
Vertical Shift (VSH)
014
HBL
RGB Blanking Mode
015
WBF
Timing of Wide Blanking (WBF)
016
WBR
Timing of Wide Blanking (WBR)
017
SBL
Service Blanking
018
COPY
Copy the GEOM data to all
50/60Hz NVM area
50/60Hz NVM area
WIDE MODE (60Hz)
(V-Compression Adjustment)
1. Input mono scope signal.
2. Adjust condition change to WIDE MODE : ON
3. "COPY" is set to
1. Input mono scope signal.
2. Adjust condition change to WIDE MODE : ON
3. "COPY" is set to
1
, then [MUTE] +
-
3-5.
PICTURE DISTORTION ADJUSTMENT
H. CENTER ADJUSTMENT (HPOS)
1. Input Monoscope signal.
2. Activate the Service Adjustment Mode.
3. Select the HPOS item with
1. Input Monoscope signal.
2. Activate the Service Adjustment Mode.
3. Select the HPOS item with
1
and
4
.
4. Adjust the value of HPOS with
3
and
6
for the best
vertical center.
5. Press [MUTING] then
-
to save into the memory.
H. SIZE ADJUSTMENT (HSIZ)
1. Input Monoscope signal.
2. Activate the Service Adjustment Mode.
3. Select HSIZ with
1. Input Monoscope signal.
2. Activate the Service Adjustment Mode.
3. Select HSIZ with
1
and
4
.
4. Adjust with
3
and
6
for the best horizontal size.
5. Press [MUTING] then
-
to save into the memory.
V. SIZE ADJUSTMENT (VSIZ)
1. Input Monoscope signal.
2. Activate the Service Adjustment Mode.
3. Select the VSIZ item with
1. Input Monoscope signal.
2. Activate the Service Adjustment Mode.
3. Select the VSIZ item with
1
and
4
.
4. Adjust value of VPOS with
3
and
6
for the best
vertical center.
5. Press [MUTING] then
-
to save into the memory.
V. CENTER ADJUSTMENT (VPOS)
1. Input Monoscope signal.
2. Activate the Service Adjustment Mode.
3. Select the VPOS item with
1. Input Monoscope signal.
2. Activate the Service Adjustment Mode.
3. Select the VPOS item with
1
and
4
.
4. Adjust value of VPOS with
3
and
6
for the best
vertical center.
5. Press [MUTING] then
-
to save into the memory.
4. Rasie/lower data using the
3
and
6
buttons adjust
the following items:-
– 32 –
KV-21HFV100
RM-W112
V. LINEARITY (VLIN), S. CORRECTION (SCOR), EW
PARABOLA/WIDTH (PW)(EWPW), AND EW
TRAPEZIUM (EWTZ) ADJUSTMENTS
1. Input Monoscope signal.
2. Activate the Service Adjustment Mode.
3. Select VLIN, SCOR, EWPW, and EWTZ with
PARABOLA/WIDTH (PW)(EWPW), AND EW
TRAPEZIUM (EWTZ) ADJUSTMENTS
1. Input Monoscope signal.
2. Activate the Service Adjustment Mode.
3. Select VLIN, SCOR, EWPW, and EWTZ with
1
and
4
.
4. Adjust with
3
and
6
for the best horizontal size.
5. Press [MUTING] then
-
to save into the memory.
H. PARALLELLOGRAM (HPAR), H. BOW (HBOW),
UPPER CORNER PARABOLA (UCOP) AND LOWER
CORNER PARABOLA (LCOP) ADJUSTMENTS
1. Input Monoscope signal.
2. Activate the Service Adjustment Mode.
3. Select HPAR, HBOW, UCOP, and LCOP with
UPPER CORNER PARABOLA (UCOP) AND LOWER
CORNER PARABOLA (LCOP) ADJUSTMENTS
1. Input Monoscope signal.
2. Activate the Service Adjustment Mode.
3. Select HPAR, HBOW, UCOP, and LCOP with
1
and
4
.
4. Adjust with
3
and
6
for the best picture.
5. Press [MUTING] then
-
to save into the memory.
EW UPPER CORNER PARABOLA (UCOP)
EW LOWER CORNER PARABOLA (LCOP)
HORIZONTAL PARALLELOGRAM
HORIZONTAL BOW (HBOW)
EW TRAPEZIUM (EWTZ)
EW PARABOLA/WIDTH (PW) (EWPW)
S-CORRECTION (SCOR)
VERTICAL LINEARITY (VLIN)
Click on the first or last page to see other KV-21HFV100 (serv.man2) service manuals if exist.