DOWNLOAD Sony KP-HW512K90 Service Manual ↓ Size: 13.82 MB | Pages: 127 in PDF or view online for FREE

– 25 –

1) Set NTSC Full mode.

2) Enter the Service mode, and select “PJE”.

Note : When you replaced printed circuit boards or devices or

CRTs, and when correction is drastically necessary, press
“7” + “ENTER”  buttons to initialize the data in the Pro-
jector Engine mode.
 Press “MUTING” + “ENTER” buttons on the com-
mander to write the data.

Note : Before this adjustment, input the data of PJE item No. 78-

85, (See page 25 or 26).

1. Place the caps on the red and blue lenses so that only the

green color is displayed.

2. Enter the monoscope signal and set to NTSC Full mode .

3. Enter the Service mode, and select “2150D-1” .

4. Adjust  “0 VPOS” and “1 VSIZ” so that the picture is dis-

played in the center of screen.

5. Adjust “2 VSZO” for 1080i vertical size adjustment.

6. Select “2150D-2” and adjust “2 H-Size” so that the picture

size is within the specification.

1) At the 4 insides of the screen, locate the middle. Use a tape

measure to identify the middle.

: middle

Change the
display mode

* When the NTSC Full mode
   adjustment has finished,
   copy its data to the next dispiay mode
   at the first time only and be sure to
   adjust in the order given.

¥ ADJUSTING FLOW

START

Turn on the power and wait for 10 minutes.

Set to the NTSC Full mode

Check the deflection yokes, the centering magnets, 2 pole/4 pole magnets

Set to the service mode.

MAIN DEFLECTION ADJUSTMENT (Green)

Green coarse adjustment

Green fine adjustment

Red coarse adjustment

Red fine adjustment

Blue fine adjustment

Blue coarse adjustment

Memorize the FLASH FOCUS offset data

End

Another display mode?

SUB DEFLECTION
ADJUSTMENT

ALLCOPY* Yes

No

(Item 3-11-2)

(Item 3-11-4)

7. Copy the dada of NTSC Full mode to the other display mode

and adjust in the other mode as the occasion demands.

2 H-Size

0 VPOS

1 V-Size

 

SPEC

Overscan Spec. = 9%

Input Signal

H SIZE

V SIZE

Monoscope

15.6 

± 0.2 sq.

11.5 

± 0.2 sq.

– 26 –

1) Enter the Service mode, and select “PJE”.

2) Press  “1” or “4” button on the commander to select the

item, and use the joystick to change the data.

3) Select  “GRN CENT” . When BLU or RED is displayed,

press “3” button on the commander to change the adjust-

ment color in the order of GRN 

c BLU c  RED.

4) In the GRN, BLU, or RED mode,move v,  Vdirection the

joystick can change the data in vertical direction, or b,  B

direction in horizontal direction.

5) Before returning to the Service mode, press “MUTING”

+“ENTER” buttons on the commander to write the data.

(Omission of this operation causes the set data to be returned

to the data before adjustment)

PJE

00

00

FDIS

Adjustment Item

Item No.

Data

v, B direction:Data up

V, b direction:Data down

GRN

000

000

CENT

Adjustment Item

Data (H)

Data (V)

Color

b : Data (H) up

B : Data (H) down

v : Data (V) up

V : Data (V) down

Commander Function

Buttons

Mode

Description

-

 + ENTER

READ

Writes data to NVM.

MUTING+ENTER

WRITE

Reads data from NVM.

7

 + ENTER

PJE

Service data initialization. Not stored.

INITIAL

(Be sure not to use usually)

Joystick

• 1

: Changes adjustment item. (item No. moves up)

: Marker moves clockwise from center to out-

side. (in fine adjustment mode)

• 4

: Changes adjustment item.

(item No. moves down)

: Marker moves counterclockwise from outside

to center. (in fine adjustment mode)

• 2

: Changes adjustment category.

(category No. moves up)

• 5

: Changes adjustment category.

(category No. moves down)

• Joystick : Changes data value. (up or down)

: Marker moves up, down, or to the left or right.

(in fine adjustment mode)

• 3

: Changes adjustment color.

                          GRN 

c BLU c RED

• 6

: Displays or changes internal test signals.

: crosshatch + external signal 

c crosshatch +bor-

derline 

c crosshatch only c dot only c off

• 9

: Switches adjustment mode.

Coarse adjustment mode 

c fine adjustment

mode

Color change

Internal test signal

Mode select
(Fine or Coarse)

Adjustment item
up

Adjustment item
down

Category up

Category down

RM-Y909K

Copy PAL data
to NTSC

TV POWER

VOLUME +

DISPLAY

Initialize data
(Not stored)

data up/down

MUTING

ENTER

MENU

• Press joy  : Switches marker moving method.

  stick

(in fine adjustment mode)

 joystick (v, V, b, B) keys 

c 1 and 4 buttons

– 27 –

Push the joystick 
to v

Push the joystick 
to V

Push the joystick 
to B

Push the joystick 
to b

• GRN CENT (horizontally/vertically)

• The adjustment should be done in the numerical order

given.

1) Place the caps on the red and blue lenses so that only the

green color is displayed.

2) Enter the monoscope signal to set.

3) Select the PJE mode.

4) Press “6” button on the commander to display internal test

signal (crosshatch).

5) Select “GRN CENT”, and adjust so that the picture coincide

in the center of screen.

Adjustment Type

Adjustment Item

GRN

RED

BLU

H / V

H / V

H / V

CENT

a / a

a / a

a / a

SKEW

a / a

a / a

a / a

SIZE

a / a

a / a

a / a

LIN

a / a

a / a

a / a

KEY

– / a

– / a

– / a

PIN

a / a

a / a

a / a

MLIN

a / –

a / –

a / –

MSIZ

a / –

a / –

a / –

Adjustment

a : Yes

– : No

1) Select the PJE mode.

2) Select FDIS so that the data at each position can be displayed

in the fine adjustment mode, and set the data to “01”.

3) Press  “9” button on the commander, and the fine adjust-

ment mode will be active where a green marker appears in

the center of screen (in the case of GRN mode).

4) Press joystick, and the marker color will be switched be-

tween green (GRN mode) and white alternately.

5) Use “1” or “4” button on the commander, or the joystick

to move the marker to the position to be adjusted, where fine

adjustment can be made.

• When marker color is white.

(in this case, fine adjustment is disabled)

Operating the joystick can move the marker

up, down, or to the left or right freely.

• When marker color is green. (GRN mode)

1

: moves the marker clockwise from center to outside.

4

: moves the marker counterclockwise from outside to center.

• Fine adjustment can be made on the basis of marker

position using v, V, b, B directiom of the joystick.

6) Press “9” button on the commander to return to the coarse

adjustment mode.

CROSSHATCH

Move joystick v direction

Move joystick B direction

CROSSHATCH

Note: If the value of over the limit value, adjust these in the fine
          adjustment .

   Coarse Data Limit Valune.
   Cent H 35

±170 V 20±170, Size H-75max, Lin H Blu

   -425min, H Red 425max.

– 28 –

• GRN MLIN (horizontally)

11) Select “GRN MLIN”, and correct the sizes of the horizontal

line at the center of the screen are symmetrical left and right.

10) Select “GRN MSIZ”, and correct the space intervals for the

horizontal section of the screen are equal.

• GRN MSIZ (horizontally)

Push the joystick 
to B

Push the joystick 
to b

Push the joystick 
to B

Push the joystick 
to b

7) Select “GRN SKEW”, and correct the tilt of horizontal lines

and vertical lines.

8) Select “GRN SIZE”, and adjust so that each distance from

center to left end and to right end is equal. Adjust so that

each distance from center to top and to bottom is equal.

• GRN SIZE (horizontally/vertically)

9) Select “GRN LIN”, and adjust so that each space at the right

end and at the left end of screen is equal. Adjust so that each

space at the top and at the bottom of screen is equal.

• GRN LIN (horizontally/vertically)

Push the joystick 
to v

Push the joystick 
to V

Push the joystick 
to B

Push the joystick 
to b

Push the joystick 
to v

Push the joystick 
to V

Push the joystick 
to B

Push the joystick 
to b

Push the joystick 
to B

Push the joystick 
to b

Push the joystick 
to v

Push the joystick 
to V

Note: The SIZE and LIN, MSIZ and MLIN adjustments are
          affected each other.
          So adjust these mutually if necessary.

Push the joystick 
to v

Push the joystick 
to B

Push the joystick 
to b

Push the joystick 
to V

12) Select “GRN PIN”, and adjust so that right and left vertical

lines on the screen become straight. Adjust so that upper and

lower horizontal lines on the screen become straight.

• GRN PIN (horizontally/vertically)

13) Select “GRN KEY”, and adjust so that upper and lower hori-

zontal lines on the screen become parallel.

• GRN KEY (vertically)

Push the joystick 
to v

Push the joystick 
to V

Note: The VPINand KEY adjustments are affected each other.
          So adjust these mutually if necessary.

• GRN SKEW (horizontally/vertically)