DOWNLOAD Sony KP-57WV600 / KP-57WV700 / KP-65WV600 / KP-65WV700 Service Manual ↓ Size: 11.53 MB | Pages: 127 in PDF or view online for FREE

Eight screws 
(KP-57WV600/ 
57WV700 Only)
Dome Washer
(Hex Tap 4x20)

Seventeen screws 
Dome Washer
(Hex Tap 4x20)

1

1

Beznet assy

2

HC board

L screen 
holder

Claws

SR board

Sensor 
bracket (B)

One screw
(+BVTP 4x12)

Four screws
(+BVTP 4x12)

One screw
(+BVTP 4x12)

Sensor 
bracket (A)

7

6

4

1

2

3

5

The Screen Holder does not need 
to be removed in order to remove 
the SR boards.

Twenty-one screws 
(Screw (4x20), tapping)

Mirror cover

1

2

1. Receive the Monoscope signal..
2. Set BRIGHTNESS to 50% and PICTURE to minimum.
3. Turn the red VR on the focus block all the way to the left and then 

gradually turn it to the right until the retrace line is barely visible.

4. Gradually turn the control to the left until the retrace line disappears.

FOCUS Block

If the jig described below is available, it is recommended that the G2 
Fine Mode Adjustment be performed to set the screen controls to their 
optimal condition.   If desired, you can build the jig illustrated below, 
using 3-watt resistors.  Please note that if the proper voltage is not 
obtained with the listed resistor’s values, then increase or decrease one 
of the values in the resistor network to obtain the correct voltage.

1. Select VIDEO-1 mode no signal applied (the screen must be black).
2. Connect the G2 JIG.
3. SW on JIG.
4. Connect an oscilloscope to the TP9101(KR), TP9201(KG) and 

TP9301(KB) of CR board, CG board, and CB board.

5. Adjust red, green, and blue screen voltage to 177.5+/-0.5V with screen 

VR on the focus block.

177.5V +/- 0.5V

G2 JIG

TP9202

(210V)

TO CG BOARD

GND

3.3k

5.6k

5.6k

6.8k

SW

K

GND

pedestal level

All resistors are 3W type

 
1.  Connect the color bar generator monoscope patter to Video 1 input.
2.  Cover the red and blue CRT lenses with lens caps to allow only green 

to show (or use the method shown in the note below for turning off the 
CRTs individually without using lens caps).

3.  Loosen the CRT’s deß ection yoke set screw and align the tilt of 

the deß ection yoke so that the horizontal bars at the center of the 
cross-hatch pattern are parallel to the top and bottom edges of the 
screen. 

4.  After aligning the deß ection yoke fasten it securely to the 

funnel-shaped portion (neck) of the CRT.

5.  Cover the green and blue CRT lenses with lens caps to allow only 

green to show (or use the method shown in the note below for turning 
off the CRTs individually without using lens caps), then repeat steps 
3 and 4 for the red CRT.  

  Cover the green and red CRT lenses with lens caps o allow only 

green to show (or use the method shown in the note below for turning 
off the CRTs individually without using lens caps), then repeat steps 
3 and 4 for the blue CRT.  

Note: If lens caps are unavailable, you can cut off the unnecessary color 
beams by controlling the service mode 2170P-2 RGBS.

2-pole magnet

4-pole magnet

Deflection yoke

Anode cap

Centering magnet

In this adjustment, use the remote commander while in service mode.  
For details on the usage of the service mode and the remote 
commander, please refer to section 
2-10. ELECTRICAL ADJUSTMENTS BY REMOTE COMMANDER.

1.  Loosen the lens screw.
2.  Cover the red and blue CRT lenses with lens caps to allow only green 

to show (or use the method shown in the note below for turning off the 
CRTs individually without using lens caps).

3.  Turn the green lens to adjust to the optimum focus point with the 

crosshatch signal.

4.  Tighten the lens screw.
5.  Cover the green and blue CRT lenses with the lens caps to allow only 

red to show (or use the method shown in the note below for turning off 
the CRTs individually without using lens caps).

6.  Turn the red lens to adjust to the optimum focus point with the 

crosshatch signal.

7.  Tighten the lens screw.
8.  Cover the green and red CRT lenses with the lens caps to allow only 

blue to show (or use the method shown in the note below for turning 
off the CRTs individually without using lens caps).

9.  Turn the blue lens to adjust to the optimum focus point with the 

crosshatch signal.

10. Tighten the lens screw.
11.  After adjusting the items:
  2-5. FOCUS VR ADJUSTMENT, 
  2-6. 2-POLE MAGNET ADJUSTMENT, 
  2-8. 4-POLE MAGNET ADJUSTMENT, 
  

reconÞ rm the optimum focus point and adjust again if necessary.

* In PJE mode, every time 6 is pressed, the test signal changes to: 

“crosshatch+video signal” 

→

 “crosshatch+borderline(black)” 

→

 

”crosshatch(black)” 

→

 “dots(black)” 

→

 off

 Test Signal

A

B

Lens

Minimize both A and B.

Center of crosshatch

Scanning line visible.

Note: If lens caps are unavailable, you can cut off the unnecessary color 
beams by controlling the service mode 2170P-2 1 RGBS.

1.  Set generator to crosshatch.
2.  Cover the red and blue CRT lenses with lens caps to allow only green 

to show (or use the method shown in the note below for turning off the 
CRTs individually without using lens caps).

3.  Turn the green focus VR on the focus block to adjust to the optimum 

focus point with the crosshatch signal.

4.  Cover the green and blue picture lenses with lens caps to allow only  

red to show (or use the method shown in the note below for turning off 
the CRTs individually without using lens caps).

5.  Turn the red focus VR on the focus block to adjust to the optimum 

focus point with the crosshatch signal.

6.  Cover the green and red picture lenses with lens caps to allow only 

blue to show (or use the method shown in the note below for turning 
off the CRTs individually without using lens caps).

7.  Turn the blue focus VR on the focus block to adjust to the optimum 

focus point with the crosshatch signal.

8.   After adjusting the items:
  2-4. FOCUS LENS ADJUSTMENT, 
  2-6. 2-POLE MAGNET ADJUSTMENT, 
  2-8. 4-POLE MAGNET ADJUSTMENT, 
  

reconÞ rm the optimum focus point and adjust again if necessary.

Note: If lens caps are unavailable, you can cut off the unnecessary color 
beams by controlling the service mode 2170P-2 1 RGBS.

FOCUS Block