DOWNLOAD Sony KP-51DS1U Service Manual ↓ Size: 14.76 MB | Pages: 112 in PDF or view online for FREE

– 9 –

54

Noise on Centre Speaker Only

55

Noise on Surround Speaker Only

56

Set Colour to minimum and Picture to maximum

57

Set Colour & Picture to minimum and adjust sub-brightness

68

Pre-Set AV Labels

69

Picture Blanking Pulse Enable/ Disable

72

Balance Left/ Right (Press RED Key for balance left, YELLOW for balance right, and GREEN for centre balance

73

Dual sound Headphones (GREEN key for A, BLUE key for B)

74

Dual sound Speakers (GREEN key for A, BLUE key for B)

77

Setup Trap Switch

78

Set Screen Size

79

Wide Setup

81

Velocity Modulation ON

82

Velocity Modulation OFF

83

Special Picture Mode - Personal mode, reset & brightness  =0

84

Text Interlace Odd  (Non Interlace mode = 3)

85

Text Interlace Even (Non interlace mode = 2)

86

Auto Cut Off ENABLE

87

Auto Cut Off DISABLE

88

Diagnostics OFF

89

Diagnostics ON

91

Clear & Disable OSD

92

Enable OSD

93

D / K Nicam Enable

94

D / K Nicam Disable

95

Reset language select menu on power up

96

Set all programme labels to default

97

MHEG mode on/off

– 10 –

One Remote Control 

(RM-892)

(conectores lado izquierdo)

(conectores lado derecho)

S

RM 892

PROGR

MENU

VIDEO

TV

Two batteries (R6 type)

/Off Switch 

Standby

indicator

Volume control

buttons

Selecting

input source

S Video

Input jack

Video Input

jack 

Audio Input 

jacks

Auto

Convergence

button

Headphone

jack

(left side connectors)

(right side connectors)

Press on the mark 

, on

the front of the projection

TV to reveal the front

connectors.

Programme up
or down buttons 
(selects TV channels)

 

Overview

S

RM 892

PROGR

MENU

VIDEO

TV

VIDEO

TV

VTR 1 2 3 4  DVD

CH

Getting Started - Overview

To Temporarily Switch Off projection
TV
Press to temporarily switch off TV (the
standby indicator   on projection TV lights
up). Press again to switch on TV from
standby mode.
To save energy we recommend switching off
completely when TV is not in use.

After 15-30 minutes without a
signal and without any button being
pressed, the projection TV switches
automatically into standby mode.

Displaying On Screen Information
Press to display all on-screen indications.
Press again to cancel.

Selecting Input source
Press repeatedly until the desired input
symbol of the source appears on the screen.

Back to the channel last watched
Press to watch the last channel selected
(watched for at least 5 seconds).

Selecting Screen format
Press repeteadly to change the format of the
screen.

This button only works in Teletext mode.
Function 

 associated to this button does not

4   Scroll Up

$   Scroll Down

Z   Previous menu or selection

z   Next menu or selection

OK Confirms your selection

Selecting channels
Press to select the next or previous channel.

Displaying the menu system
Press to display the menu on the screen.
Press again to remove the menu display
from the screen.

Press to mute TV sound.

Press again to restore the sound.

Press to switch your VCR on or off.

Press to switch off Teletext or video input.

Press to switch on Teletext.

Press to display the Electronic Programme

Guide (EPG). Press again to switch off EPG.

These buttons do not work on this set.

Press to select channels.

For double-digit programme numbers, e.g. 23,
press -/-- first, then the buttons 2 and 3.
If you enter an incorrect first digit, this should
be corrected by entering another digit (0-9)
and then selecting -/-- button again to enter
the programme number of your choice.

+++++++++++++++...

Press repeatedly to change the sound mode.

+++++++++++++++++...

Press repeatedly to change the picture mode.

+++++++++++++++++...

Press to adjust the volume of the TV.

Besides TV functions, all coloured buttons as well as green
symbols are also used for Teletext operation. For more details,
please refer to the "Teletext" section of this instruction manual.

  This button does not work on this set.

Displaying the time
Press to switch the time on or off
(available only when teletext is
broadcast).

VCR operation
For more details, please refer to
the section "Remote Control of
other Sony Equipment"

– 11 –

Make sure you insert the batteries using the correct polarities.
Always remember to dispose of used batteries in an environmental friendly way.

Connecting cables are not supplied.

OUT

IN

VCR

The Scart lead is optional.
If you use this optional connection
it can improve picture and sound quality
when using a VCR.

If you do not use a SCART lead, after 
automatically tuning the projection TV
refer to the "Manually Tuning the TV"
section of this instruction manual, to tune
in the projection TV to the output of your
VCR. Also refer to your VCR instruction
manual to find out how to find the output 
channel of your VCR.

Installation

The first time you switch on your TV, a sequence  of menu screen appear on the TV enabling you to 1) choose the language
of the menu screen, 2) search and stores all available channels (TV Broadcast) and 3) change the order in which the channels

 

(TV Broadcast) appear on the screen.
However, if you need to change the language menu, change the country, change or repeat the tuning (e.g. when you move

 house) or rearrange again the order of the channels afterwards, you can do that by selecting the appropriate menu in
 the 

 (PRESET).

Connect the Projection TV plug to the mains socket (220-240V AC,
50 Hz). Press the 

 on/off button on your projection TV set to

switch on. The first time you press this button the Language menu 

displays automatically on the screen.

Push the joystick on the remote control to 

$ or 4 to select the 

language,  then press OK to confirm your selection. From now on all 
the menus will appear in the selected language.

The Auto Tuning menu appears on the screen in the selected 

language, then press the OK button on the remote control to select 
YES

.

A new menu appears automatically on the screen asking you to
check that the aerial is connected. Confirm that the aerial is connected 

and then press the OK button to start the automatic tuning. 

The TV starts to automatically search and store all available    
channels (TV Broadcast) for you and the message “Searching” 
flashes on the screen until all available channels will be stored.
If any analogue channel is tuned, it will be stored in 
programme numbers 91 to 99 but only in the case that these 
positions are free. However, if you wish to tune in any 
analogue channel and store it in the programme number of 
your choice, please refer to the section "Manually Tuning the 
TV" of this instruction manual. 

This procedure could take some minutes. Please, be patient and    
do not press any button. Otherwise the automatic tuning will
not be completed.

   

continued...

First Time Operation

S

RM 892

PROGR

MENU

VIDEO

TV

–

 12 

–

S

RM 892

PROGR

MENU

VIDE

O

TV

 

After all available channels are captured and stored, the 
Programme Sorting menu appears automatically on the screen 
enabling you to change the order in which the channels appear 
on the screen.

 

If you do not wish to change the channel order, go to step 6.

 

If you wish to change the channel order:

 

Push the joystick on the remote control to 

 

$

 

 or 

 

4

 

 to select the 

programme number with the channel (TV Broadcast) you wish to 
rearrange, then push to 

 

z

 

.

 

 Push the joystick to 

 

$

 

 or 

 

4

 

 to select the new programme number 

position for your selected channel (TV Broadcast), then press 

 

.

The selected channel now moves to its new programme
position and the other channels move accordingly.

 

Repeat steps b1) and b2) if you wish to change the order of the
other channels.

 

Press the 

 

 button to exit and return to the normal TV screen.

 

       

 

First Time Operation

 

Press the 

 

 button to switch the first level menu on.

 

•To higlight the desired menu or option, push the joystick to

 

4

 

 or 

 

$

 

.

•To enter to the selected menu or option, push to 

 

z

 

•To return to the last menu or option, push to 

 

Z

 

.

•To alter settings of your selected option, push to 

 

$

 

/

 

4

 

/

 

Z

 

 or 

 

z

 

.

•To confirm and store your selection, press 

 

.

 

Press the 

 

 button to remove the menu from the screen.

Your projection TV uses an on-screen menu system to guide you through the operations. Use the following buttons on the Remote

 

Control to operate the menu system:

S

RM 892

PROGR

MENU

VIDEO

TV

  push to 

$/4/Z or z

press OK

Menu System

(For different adjustments, please refer to
the section "Adjusting the Picture")

(For different adjustments, please refer to
the section "Adjusting the Sound" )

(For more details, please refer to the
section "Selecting the output source for the
Euro AV connectors")

(For more details, please refer to the
section "Using the Sleep Timer")

(For more details, please refer to the
section "Switching on the projection TV
and automatically tuning")

(For more details, please refer to the
section "Manually Tuning the TV")

(For more details, please refer to the
section "Using the Further Programme
Preset function"

(For more details, please refer to the
section "Labelling the Input Sources")

(For more details, please refer to the
section "Switching on the projection TV
and automatically tuning")

(For more details, please refer to the
section "Locking Programmes").

(For more details, please refer to the
section "Switching on the projection TV
and automatically tuning")

(For more details, please refer to the
section "Adjusting Colour Registration
(Convergence)".

(For more details, please refer to the
section "Displaying subtitles for digital
channels".