Sony KP-48PS1 / KP-48PS1K / KP-53PS1 / KP-53PS1K / KP-61PS1 / KP-61PS1K Service Manual ▷ View online
– 5 –
KP- 48PS1/53PS1/61PS1
48PS1K/53PS1K/61PS1K
K
RM-892
1-2. ERROR DETECTION MONITOR
Device acknowledge is used to check IIC errors. Device acknowledge is checked by sending an IIC start sequence during CRT power
on. Each device is checked three times, if there is no acknowledge after every attempt, it will be regarded as an error.
There are three step to check errors.
1. IIC line 0
If all devices except the NVM have errors, IIC line 0 error is displayed.
2. Board check
If all devices mounted on one board have errors, board error is displayed.
3. Each device check
if IIC line error and board error are not detected then the device with an error is displayed.
The detected errors can be displayed as follows:
1. Error Monitor Menu
2. Error Reader
1-2-1. Error Monitor Menu
The error monitor menu is displayed by selecting TT33. The following menu will be displayed:
Error Monitor
1
Operating Time :
Stored Errors :
1. A-Board
Current Error :
Start Error Sequence
2. B3-B CXA2100 MID
3. J-B CXA2123 Main Col Dec
4. Error Code Not Valid
5. Error Code Not Valid
3. J-B CXA2123 Main Col Dec
4. Error Code Not Valid
5. Error Code Not Valid
Ignore Errors
OFF
000021 h 40 min
ON
ON
– 6 –
KP- 48PS1/53PS1/61PS1
48PS1K/53PS1K/61PS1K
K
RM-892
1-2-2. Error Reader Display
The error reader display is connected to the service connector to read actual error codes. The part number for the error reader display
is S-188-900-10.
Once an error has been detected it will then be displayed on the two digit error reader. The errors displayed refer to the following table:
Send Data to Error Reader
Error Code
Data High
Data Low
Error Type
Function
00 00h
–
f0h
no device
Gen. IIC Error
00 01h
f0h
01h
IIC 0 line
00 02h
f0h
02h
IIC 1 line
not used
Board Error
01 00h
f1h
00h
A Board
04 00h
f4h
00h
B3 Board
06 00h
f6h
00h
E Board
07 00h
f7h
00h
J/S Board
08 00h
f8h
00h
M Board
Device Error
A Board
01 01h
f1h
01h
CXA1875
Port Expander
01 02h
f1h
02h
TU1301
Main Tuner
01 03h
f1h
03h
TU1302
Sub Tuner
B3 Board
04 01h
f4h
01h
CXD9509
MID
E Board
06 01h
f6h
01h
CXA2100
Backend
J Board
04 04h
f4h
04h
TDA9178
Picture Booster
07 03h
f7h
03h
CXA2123
Sub Colour
07 04h
f7h
04h
CXA2123
Main Colour
07 0Ah
f7h
0Ah
CXA2149
AV SW
S Board
07 05h
f7h
05h
CXA1875
Sub Sound
07 08h
f7h
08h
MSP3410D
Sound Proc
M Board
08 01h
f8h
01h
ST24C32
NVM
– 7 –
SECTION 2
GENERAL
The operating instructions mentioned here are partial abstracts
from the Operating Instruction Manual. The page numbers of
the Operating Instruction Manual remain as in the manual.
from the Operating Instruction Manual. The page numbers of
the Operating Instruction Manual remain as in the manual.
4
RM 892
PROGR
MENU
1
4
7
2
5
8
0
3
6
9
VIDEO
TV
Overview
Checking the Accessories Supplied
One Remote Control
(RM-892)
Two batteries (R6 type)
Overview
Overview of Projection TV Buttons
Auto
Convergence
button
Convergence
button
Press on the mark
, on
the front of the projection
TV to reveal the front
connectors.
Headphone
jack
jack
On
/Off Switch
Standby
indicator
indicator
Selecting
input source
input source
Volume control
buttons
buttons
Programme up or
down buttons (selects
TV channels)
down buttons (selects
TV channels)
(left side connectors)
(right side connectors)
S Video
Input jack
Input jack
Video Input
jack
jack
Audio Input
jacks
jacks
5
GB
Overview
Overview
Overview of Remote Control Buttons
To Temporarily Switch Off projection TV
Press to temporarily switch off TV (the standby
indicator on projection TV lights up). Press
again to switch on TV from standby mode.
To save energy we recommend switching off
completely when TV is not in use.
Press to temporarily switch off TV (the standby
indicator on projection TV lights up). Press
again to switch on TV from standby mode.
To save energy we recommend switching off
completely when TV is not in use.
After 15-30 minutes without a signal and
without any button being pressed, the
projection TV switches automatically into
standby mode.
without any button being pressed, the
projection TV switches automatically into
standby mode.
Displaying On Screen Information
Press to display all on-screen indications.
Press again to cancel.
Press to display all on-screen indications.
Press again to cancel.
Selecting Input source
Press repeatedly until the desired input symbol
of the source appears on the screen.
Press repeatedly until the desired input symbol
of the source appears on the screen.
Back to the channel last watched
Press to watch the last channel selected (watched
for at least 5 seconds).
Press to watch the last channel selected (watched
for at least 5 seconds).
Selecting Screen format
Press repeteadly to change the format of the
screen 4:3 for a conventional 4:3 picture or 16:9
for a imitation of wide screen effect. 16:9 picture
is available only if you have selected Digital
Mode DRC 100 (PAL mode) in the Picture
Adjustment menu.
Press repeteadly to change the format of the
screen 4:3 for a conventional 4:3 picture or 16:9
for a imitation of wide screen effect. 16:9 picture
is available only if you have selected Digital
Mode DRC 100 (PAL mode) in the Picture
Adjustment menu.
Displaying Multi PIP (Picture In Picture)
Press to display Multi PIP mode. Press again to
cancel.
Press to display Multi PIP mode. Press again to
cancel.
Joystick for menu selection
• When MENU is switched on:
• When MENU is switched on:
Scroll Up
Scroll Down
Previous menu or selection
Next menu or selection
Scroll Down
Previous menu or selection
Next menu or selection
OK Confirms your selection
• When MENU is switched off:
Return to the last menu screen.
OK Shows a channel overview.
Selecting channels
Press to select the next or previous channel.
Press to select the next or previous channel.
Displaying the menu system
Press to display the menu on the screen. Press
again to remove the menu display from the
screen.
Press to display the menu on the screen. Press
again to remove the menu display from the
screen.
Besides TV functions, all coloured buttons as well as green
symbols are also used for Teletext operation. For more details,
please refer to the "Teletext" section of this instruction manual.
symbols are also used for Teletext operation. For more details,
please refer to the "Teletext" section of this instruction manual.
Resetting to factory set levels
Press not only to return picture and sound
settings to factory-set levels, but also to re-
install the projection TV as the first time it was
switched on.
After the "Language/Country" menu appeared
on the screen, proceed in the same way as
described in the section "Switching on the
Projection TV and automatically Tuning" of this
instruction manual.
Press not only to return picture and sound
settings to factory-set levels, but also to re-
install the projection TV as the first time it was
switched on.
After the "Language/Country" menu appeared
on the screen, proceed in the same way as
described in the section "Switching on the
Projection TV and automatically Tuning" of this
instruction manual.
Displaying the time
Press to switch the time on or off
(available only when teletext is
broadcast).
Press to switch the time on or off
(available only when teletext is
broadcast).
VCR operation
For more details, please refer to the
section "Remote Control of other
Sony Equipment"
For more details, please refer to the
section "Remote Control of other
Sony Equipment"
VCR on/off
Press to switch your VCR on or off.
Press to switch your VCR on or off.
Muting the Sound
Press to mute TV sound.
Press again to restore the sound.
Press to mute TV sound.
Press again to restore the sound.
Selecting TV mode
Press to switch off Teletext or video input.
Press to switch off Teletext or video input.
PAP (Picture And Picture)
For more details, please refer to the section
"Using PAP (Picture And Picture)".
For more details, please refer to the section
"Using PAP (Picture And Picture)".
Selecting Teletext
Press to switch on Teletext.
Press to switch on Teletext.
Displaying EPG
Press to display the Electronic Programme
Guide (EPG). Press again to switch off EPG.
Press to display the Electronic Programme
Guide (EPG). Press again to switch off EPG.
Freezing the picture
Press to freeze the picture. Press again to return
to the normal picture.
Press to freeze the picture. Press again to return
to the normal picture.
Selecting channels
Press to select channels.
Press to select channels.
For double-digit programme numbers, e.g. 23,
press -/-- first, then the buttons 2 and 3.
If you enter an incorrect first digit, this should
be corrected by entering another digit (0-9) and
then selecting -/-- button again to enter the
programme number of your choice.
press -/-- first, then the buttons 2 and 3.
If you enter an incorrect first digit, this should
be corrected by entering another digit (0-9) and
then selecting -/-- button again to enter the
programme number of your choice.
+++++++++++++++...
Selecting Sound mode
Press repeatedly to change the sound mode.
Press repeatedly to change the sound mode.
+++++++++++++++++...
Selecting Picture mode
Press repeatedly to change the picture mode.
Press repeatedly to change the picture mode.
+++++++++++++++++...
Adjusting TV Volume
Press to adjust the volume of the TV.
Press to adjust the volume of the TV.
RM 892
PROGR
MENU
1
4
7
2
5
8
0
3
6
9
K
VIDEO
TV
VIDEO
TV
VTR 1 2 3 4 DVD
C H
–
8
–
–
6
Installation
Installation
Inserting Batteries into the Remote Control
Make sure you insert the batteries using the correct polarities.
Always remember to dispose of used batteries in an environmental friendly way.
Always remember to dispose of used batteries in an environmental friendly way.
Connecting the Aerial and VCR
Connecting cables are not supplied.
The Scart lead is optional.
If you use this optional connection
it can improve picture and sound quality
when using a VCR.
If you use this optional connection
it can improve picture and sound quality
when using a VCR.
If you do not use a SCART lead, after
automatically tuning the projection TV
refer to the "Manually Tuning the TV"
section of this instruction manual, to tune
in the projection TV to the output of your
VCR. Also refer to your VCR instruction
manual to find out how to find the output
channel of your VCR.
automatically tuning the projection TV
refer to the "Manually Tuning the TV"
section of this instruction manual, to tune
in the projection TV to the output of your
VCR. Also refer to your VCR instruction
manual to find out how to find the output
channel of your VCR.
or
VCR
OUT
IN
7
GB
First Time Operation
Switching on the Projection TV and Automatically
Tuning
Tuning
The first time you switch on your TV, a sequence of menu screen appear on the TV enabling you to 1) choose the language of the
menu screen, 2) choose the country in which you wish to operate the projection TV, 3) search and stores all available channels (TV
Broadcast) and 4) change the order in which the channels (TV Broadcast) appear on the screen.
However, if you need to change the language menu, change the country, change or repeat the tuning (e.g. when you move house) or
rearrange again the order of the channels afterwards, you can do that by selecting the appropriate menu in the
menu screen, 2) choose the country in which you wish to operate the projection TV, 3) search and stores all available channels (TV
Broadcast) and 4) change the order in which the channels (TV Broadcast) appear on the screen.
However, if you need to change the language menu, change the country, change or repeat the tuning (e.g. when you move house) or
rearrange again the order of the channels afterwards, you can do that by selecting the appropriate menu in the
(Set Up).
1
Connect the Projection TV plug to the mains socket (220-240V AC,
50 Hz). Press the on/off button on your projection TV set to
switch on. The first time you press this button the Language/
Country
50 Hz). Press the on/off button on your projection TV set to
switch on. The first time you press this button the Language/
Country
menu displays automatically on the screen.
2
Push the joystick on the remote control to or to select the
language, then press OK to confirm your selection. From now on
all the menus will appear in the selected language.
language, then press OK to confirm your selection. From now on
all the menus will appear in the selected language.
3
Push the joystick to or to select the country in which you will
operate the projection TV set, then press OK to confirm your
selection.
operate the projection TV set, then press OK to confirm your
selection.
Select "Off" instead of a country if you do not want your
channels (TV Broadcasts) stored in a given channel sequence
starting from programme position 1.
channels (TV Broadcasts) stored in a given channel sequence
starting from programme position 1.
If you are operating the projection TV in the UK, we
reccommend you not to select "Off". Otherwise the On Screen
clock will not show the correct UK time.
clock will not show the correct UK time.
4
The Auto Tuning menu appears on the screen in the selected
language, then press the OK button on the remote control to select
YES
language, then press the OK button on the remote control to select
YES
.
5
A new menu appears automatically on the screen asking you to
check that the aerial is connected. Confirm that the aerial is
connected and then press the OK button to start the automatic
tuning.
check that the aerial is connected. Confirm that the aerial is
connected and then press the OK button to start the automatic
tuning.
The TV starts to automatically search and store all available
channels (TV Broadcast) for you.
This procedure could take some minutes. Please, be patient and
do not press any button. Otherwise the automatic tuning will
not be completed.
not be completed.
First Time Operation
RM 892
PROGR
MENU
1
4
7
2
5
8
0
3
6
9
VIDEO
TV
continued ...
Language/Country
Language
Country
Select Language:
Confirm: OK
Italiano
Français
Español
English
Deutsch
Dansk
â e‰
tina
Language/Country
Language
Country
Select Language:
Confirm: OK
Italiano
Français
Español
Français
Español
English
Deutsch
Dansk
â e‰
tina
Language/Country
Language
Country
Select Language:
Confirm: OK
Italiano
Français
Español
English
Deutsch
Dansk
â e‰
tina
Language/Country
Language
Country
Select Country:
Confirm: OK
Finland
Denmark
Czech Rep.
Bulgaria
Belgium
Belgium
Austria
Off
Do you want to start
automatic tuning?
automatic tuning?
Yes: OK No:
Please confirm that
aerial is connected!
aerial is connected!
Yes: OK No:
1
2
3
4
5
2
3
4
5
CO2
CO3
CO4
CO7
CO8
CO3
CO4
CO7
CO8
Searching...
Click on the first or last page to see other KP-48PS1 / KP-48PS1K / KP-53PS1 / KP-53PS1K / KP-61PS1 / KP-61PS1K service manuals if exist.