Sony KP-43T85T / KP-53SV85T / KP-61SV85T Service Manual ▷ View online
— 26 —
KP-43T85T / 53SV85T / 61SV85T
G BOARD
3-1. HV REGULATION CIRCUIT CHECK AND
ADJUSTMENT
ADJUSTMENT
When replacing the following components marked with a
Y on the
schematic diagram always check the HV regulation, and if necessary
re-adjust.
re-adjust.
X : C517
Y : C517, C521, C522, IC654, L504, T502, T504 (FBT),
DY, A board, G board
OPERATION CHECK of 31.0KV +1.0 KV DC/ -2.5 KV DC
1. Connect an HV static voltmeter to the unused socket of the high-
1. Connect an HV static voltmeter to the unused socket of the high-
voltage block. (Fig. 3-1)
2. Power on the set.
3. Display a dot pattern through the VHF/UHF input (PICTURE and
BRIGHTNESS set to minimum)
4. Check that the HV static voltmeter is reading
31.00 KV +1.0 KV DC / -2.5 KV DC.
HV Regulation adjustment
1. Connect a HV static voltmeter to the unused socket of the high-
1. Connect a HV static voltmeter to the unused socket of the high-
voltage block.
2. Power on the set.
3. Display a dot pattern through the VHF/UHF input (PICTURE and
BRIGHTNESS to minimum).
4. If anode voltage is 31.95kV or higher, change the value of C517
from 470pF/2kV to 1,000pF/2kV, and confi rm that the high voltage is
within the range specifi ed above.
within the range specifi ed above.
5. If anode voltage is 29.45kV or lower, change the value of C517 from
470pF/2kV to 100pF/2kV, and confi rm that the high voltage is within
the range specifi ed above.
the range specifi ed above.
Remove the cap from
the unused terminal and
connect a static voltmeter
here.
the unused terminal and
connect a static voltmeter
here.
3-2. HV HOLD DOWN CIRCUIT OPERATION
CHECK AND ADJUSTMENT
CHECK AND ADJUSTMENT
When replacing the following components marked with a
Y on the
schematic diagram always check the hold-down voltage and re-adjust
when necessary.
when necessary.
X : R536, R545
Y : C516, C536, D506, D507, D522, IC206, IC502, IC654,
L504, R511, R522, R536, R538, R545, R548, R584, T502,
T504 (FBT), DY, A board, G board
OPERATION CHECK
1. Unplug
1. Unplug
connector
CN652.
2. Connect an HV static voltmeter to the unused socket of the high-
voltage block.
3. Connect
a
220
Ω/200W resistor, across pin 2 and pin 1 of CN652,
and connect an external DC power supply (200V, class 2A) to pin
3 of CN652.
3 of CN652.
4. First, turn on the external power supply (+B=135V), then turn on the
power to the set.
5. Display a dot pattern through the VHF/UHF input (PICTURE and
BRIGHTNESS to minimum).
6. Gradually increase the value of the external DC power supply and
check that the hold-down circuit operates at a static HV voltmeter
reading of 33.5±1.0kVdc when the set shuts down.
reading of 33.5±1.0kVdc when the set shuts down.
7. Remove AC power from the set, then remove the 220
Ω/200W
resistor and reconnnect CN652.
HV HOLD-DOWN ADJUSTMENT
1. Repeat steps 1-8 above.
1. Repeat steps 1-8 above.
2. If hold-down voltage is 34.5kV or higher, remove R536, mount a
resistor (150k
Ω, 1/4W : RN) onto R545 instead, and check again if
the hold-down voltage is within the standard range.
3. If hold-down voltage is 32.5kV or lower, mount a resistor (220k
Ω,
1/4W : RN) onto R536 and check again if the hold-down voltage is
within the standard range.
within the standard range.
NOTE: Finish the adjustment as soon as possible.
SECTION 3: SAFETY-RELATED ADJUSTMENTS
— 27 —
KP-43T85T / 53SV85T / 61SV85T
3-3.+B MAX VOLTAGE CONFIRMATION
The following adjustments should always be performed when
replacing IC654.
1. Supply 130V +/- 2V AC to the set.
replacing IC654.
1. Supply 130V +/- 2V AC to the set.
2. Display a dot pattern through the video-1 input.
3. Set the PICTURE control and the BRIGHTNESS control to
minimum.
4. Confi rm the voltage of G BOARD test point TP135V is less than
137.0Vdc.
5. If step 4 is not satisfi ed, replace IC654 and repeat above steps.
3-4.+B OVP CONFIRMATION
1. Connect the voltmeter between test point TP OVP and ground.
2. Supply 120VAC to the set using an isolation transformer.
3. Set an adjustable external 150-Volt DC power supply to 120 VDc,
and connect it to test point OVP.
4. Power on the set.
5. Set PICTURE and BRIGHTNESS controls to minimum.
6. Gradually adjust the external DC supply towards 150 VDc, and
make sure the set shuts down when the external supply’s voltage is
between 139 VDC and 159 VDC.
between 139 VDC and 159 VDC.
— 28 —
KP-43T85T / 53SV85T / 61SV85T
4-1.TV INPUT SUB CONTRAST ADJUSTMENT
(VPNT-SCON)
(VPNT-SCON)
1. Display a color bar signal through the TV’s VHF/UHF input.
2. Mode: Personal 1 or 2
PICTURE:............... maximum COLOR:...................... minimum
BRIGHTNESS: ............. center COLORTEMP:................neutral
3. Enter the service mode.
4. Turn off the blue and red CRTs by changing the data from “1” to
“0” in category VPNT item 28 RON (red), and item 30 BON (blue).
If this step is not followed, the ABL circuit may prevent you from
adjusting the peak-to-peak amplitude to 1.8 V.
If this step is not followed, the ABL circuit may prevent you from
adjusting the peak-to-peak amplitude to 1.8 V.
5. Connect an oscilloscope between pin 7 of CN204 (A board) and
ground.
6. Select adjustment category “VPNT” adjustment item 19 “SCON”,
and adjust using the 3 or 6 button on the remote so that the wave
form level is 1.80 ± 0.05Vp-p.
form level is 1.80 ± 0.05Vp-p.
1.80 ± 0.05 Vp-p
White
Black
7. Press “MUTING” and then “ENTER” to save the adjustment data.
4-2.VIDEO INPUT SUB-HUE AND SUB-COLOR
ADJUSTMENT (VPNT-SHUE, SCOL)
ADJUSTMENT (VPNT-SHUE, SCOL)
1. Display a color bar signal through a video input.
2. Mode: Personal 1 or 2
PICTURE:............... maximum COLOR:...........................center
BRIGHTNESS: ............. center COLORTEMP:................neutral
3. Enter the service mode.
4. Connect an oscilloscope between pin 5 of CN204 (A board) and
ground.
5. Alternately select adjustment category “VPNT” adjustment item #20
“SHUE” and item #21 “SCOL”, and adjust them so that VB1 = VB4,
and VB2 = VB3 as shown below.
and VB2 = VB3 as shown below.
VB1
VB2 VB3 VB4
6. Add 2 to the adjusted value of “SCOL”.
7. Press
“MUTING” and then “ENTER” to save the adjustment data.
4-3.COMPONENT INPUT SUB-HUE AND SUB-
COLOR ADJUSTMENT (DAC-UVSH, UVSC)
COLOR ADJUSTMENT (DAC-UVSH, UVSC)
1. Select VIDEO 4 and display a color bar signal.
2. Mode: Personal 1 or 2
PICTURE:............... maximum COLOR:...........................center
BRIGHTNESS: ............. center COLORTEMP:................neutral
3. Enter the service mode.
4. Connect an oscilloscope between pin 5 of CN204 (A board) and
ground.
5. Alternately select adjustment category “DAC”, adjustment item # 0
“UVSH” and item #1 “UVSC” and adjust them so that VB1 = VB4 and
VB2 = VB3 as shown below.
VB2 = VB3 as shown below.
VB1
VB2 VB3 VB4
6. Press
“MUTING” and then “ENTER” to save the adjustment data.
4-4.PIP SUB CONTRAST ADJUSTMENT
(PYC-PSCN)
(PYC-PSCN)
1. Display a color bar signal through the TV’s VHF/UHF input.
2. Mode: Personal 1 or 2
PICTURE:............... maximum COLOR:...................... minimum
BRIGHTNESS: ............. center COLORTEMP:................neutral
3. Enter the service mode, and then select the PIP (Picture-in-Picture)
mode.
4. Select an unused video input for the main picture (it must be black),
and select the tuner for the small picture (it must be showing
colorbars).
colorbars).
5. Connect an oscilloscope between pin 7 of CN204 (A board) and
ground.
6. Select adjustment category “PYC”, adjustment item # 0 “PSCN” and
adjust so that the peak-to-peak voltage is 1.65 ± 0.05Vp-p as shown
below.
below.
1.65 ± 0.05
White
Black
7. Press “MUTING” and then “ENTER” to save the adjustment data.
SECTION 4: CIRCUIT ADJUSTMENTS
— 29 —
KP-43T85T / 53SV85T / 61SV85T
4-5.PIP SUB-HUE , SUB-COLOR
ADJUSTMENT (PYC-PHUE, PYC-PCOL)
ADJUSTMENT (PYC-PHUE, PYC-PCOL)
1. Display a color bar signal through the TV’s VHF/UHF input.
2. Mode: Personal 1 or 2.
PICTURE:............... maximum COLOR:...........................center
BRIGHTNESS: ............. center COLORTEMP:................neutral
3. Enter the service mode and select the PIP mode.
4. Connect an oscilloscope between pin 5 of CN204 (A board) and
ground.
5. Select an unused video input for the main picture (it must be black),
and select the tuner for the small picture (it must be showing
colorbars).
colorbars).
6. Alternately select adjustment category “PYC”, adjustment item # 2
“PHUE” and item #3 “PCOL” and adjust them so that VB1 = VB4 and
VB2 = VB3 as shown below.
VB2 = VB3 as shown below.
VB1
VB2 VB3 VB4
7. Press
“MUTING” and then “ENTER” to save the adjustment data.
4-6.USER-CONTROL BAR GRAPH DISPLAY
POSITION ADJUSTMENT (OP-DISP)
POSITION ADJUSTMENT (OP-DISP)
1. Select the video-1 input with no signal applied (the screen should
be black).
2. Enter the service mode.
3. Press
the
“Volume +” button so that the volume bar graph is
displayed.
4. Check to make sure the bar graph is centered on the screen
horizontally. If necessary, select adjustment category “OP”,
adjustment item # 0 “DISP”, and adjust so that the bar graph is
centered. Adjust the data 1 step at a time, and then display the bar
graph again to check its position.
adjustment item # 0 “DISP”, and adjust so that the bar graph is
centered. Adjust the data 1 step at a time, and then display the bar
graph again to check its position.
X1 = X2
X1
X2
5. Write the data into memory, press “MUTING” and then “ENTER”.
4-7.PIP POSITION ADJUSTMENT
(PIP-POFV, POFH)
(PIP-POFV, POFH)
1. Select the PIP mode.
2. Display any signal in the PIP window.
3. Alternately select adjustment category “PIP”, adjustment item # 18
“POFV” and item #19 “POFH” and adjust so that the PIP window
is equally spaced from the screen edge in each position on the
screen as shown below. Use the POSITION button on the remote to
change the screen position of the PIP window.
is equally spaced from the screen edge in each position on the
screen as shown below. Use the POSITION button on the remote to
change the screen position of the PIP window.
X1-X2 < 0.25 sq
Y1-Y2 < 0.25 sq
Y2
X2
X1
Y1
4. Write the data into memory, press “MUTING” and then “ENTER”.
Click on the first or last page to see other KP-43T85T / KP-53SV85T / KP-61SV85T service manuals if exist.