Sony KLV-40S550A Service Manual ▷ View online
– 4 –
KLV-40S550A
RM-GA015
1-5. Lead Free Information
The circuit boards used in these models have been processed
using Lead Free Solder. The boards are identified by the LF
logo located close to the board designation.
The circuit boards used in these models have been processed
using Lead Free Solder. The boards are identified by the LF
logo located close to the board designation.
The servicing of these boards requires special precautions. It
is strongly recommended to use Lead Free Solder material in
order to guarantee optimal quality of new solder joints. Lead
Free Solder is available under the following part numbers:-
is strongly recommended to use Lead Free Solder material in
order to guarantee optimal quality of new solder joints. Lead
Free Solder is available under the following part numbers:-
Due to high melting point of Lead Free Solder, the soldering
iron tip temperature needs to be set to 370 degrees
centigrade. This requires soldering equipment capable of
accurate temperature control coupled with a good heat
recovery characteristics.
iron tip temperature needs to be set to 370 degrees
centigrade. This requires soldering equipment capable of
accurate temperature control coupled with a good heat
recovery characteristics.
For more information on the use of Lead Free Solder,
please refer to
please refer to
http://www.sony-training.com
1-6. Attachment & Detachment of MDF61 Connector
(If applicable for these models)
a) Insertion
r
e
b
m
u
n
t
r
a
P
r
e
t
e
m
a
i
D
s
k
r
a
m
e
R
9
1
-
5
0
0
-
0
4
6
-
mm
m
m
m
m
m
m
m
3
.
0
Kg
5
2
.
0
0
2
-
5
0
0
-
0
4
6
-
7
m
4
.
0
Kg
0
5
.
0
1
2
-
5
0
0
-
0
4
6
-
7
m
5
.
0
Kg
0
5
.
0
2
2
-
5
0
0
-
0
4
6
-
7
m
6
.
0
Kg
5
2
.
0
3
2
-
5
0
0
-
0
4
6
-
7
m
8
.
0
Kg
0
0
.
1
4
2
-
5
0
0
-
0
4
6
-
7
m
0
.
1
Kg
0
0
.
1
5
2
-
5
0
0
-
0
4
6
-
7
m
2
.
1
Kg
0
0
.
1
6
2
-
5
0
0
-
0
4
6
-
7
m
6
.
1
Kg
0
0
.
1
7
Figure 2: LF logo
Figure 3: LF logo on circuit board
(1) Hold the center of a
connector.
connector.
(2) Press the center of the
connector to insert it.
(3) Slide the slider to lock the
connector.
connector.
Lock
b) Detachment
(1) Slide the slider to release
the slider lock.
(2) Press the center lock tab
to release the lock and pull
the connector up.
to release the lock and pull
the connector up.
Unlock
1-7. Attachment, Detachment & Confirmation of Lock
Condition of JST IBH Connector
(If applicable for these models)
(If applicable for these models)
Attention: This is a SAFETY CRITICAL PROCESS.
a) Attachment
(1) Press the center of the connector to insert it.
(2) Press position
(NG for red marking portion)
(NG for red marking portion)
(3) Prohibited matter (Refer Figure A~C explanation)
Figure A
Figure B
Figure C
Figure A: Do not press lock
portion.
Figure B: Do not press the
front side of the
connector.
connector.
Figure C: Do not press the side
of the connector.
– 5 –
KLV-40S550A
RM-GA015
b) Detachment
(1) Hold between the lock part and harness of socket.
Release the lock and pull out connector within 20
degree.
degree.
(2) Prohibited matter (Refer Figure D & E explanation)
Figure D: Do not pull out by holding the harness only.
Figure E: Do not pull out the connector when it does not
Figure E: Do not pull out the connector when it does not
release the lock.
Figure D
Figure E
Figure F
Figure G
c) Confirmation of Lock Condition
(1) Confirm the lock conditions. When lock is completed,
base and socket must be same line as shown in Figure
F and G.
F and G.
(2) NG Condition
It is NG condition when there are some gap between
base and socket such as in Figure H and I.
base and socket such as in Figure H and I.
Figure H
Figure I
Gap
Gap
– 6 –
KLV-40S550A
RM-GA015
a) REMOVAL
b) INSTALLATION
Push Point
Rear Cover
Switch Unit
Push towards inner set on top area of
Program Button(with printing).
Program Button(with printing).
Step 1: Install Rear Cover to Bezel.
Caution point:-
1a) Make sure Rear Cover is not overlapped with
Bezel.
Step 2: Screw the Rear Cover.
Step 3: Push the Rear Cover at point 3 until click sound is
Step 3: Push the Rear Cover at point 3 until click sound is
heard.
Remove Rear Cover from Switch Unit
while pushing at Switch Unit towards
inner side of set.
while pushing at Switch Unit towards
inner side of set.
1-8. REMOVAL AND INSTALLATION OF REAR COVER PROCEDURE
Bezel
Side Button
PUSH
3
1a
1a
1a
1a
– 7 –
KLV-40S550A
RM-GA015
a) REMOVAL
Panel
Bezel
Switch Unit
2
1
Push and slant towards inner side of set
Step 1: Push the switch unit a little upwards carefully.
Step 2: Push and slant the switch unit towards inner
Step 2: Push and slant the switch unit towards inner
side of set to remove it correctly.
1-9. Removal of Switch Unit Procedure
Click on the first or last page to see other KLV-40S550A service manuals if exist.