DOWNLOAD Sony KLV-26T400A / KLV-26T400G / KLV-32T400A Service Manual ↓ Size: 3.16 MB | Pages: 43 in PDF or view online for FREE

– 16 –

1) Install Ferrite core to AC power cord at specified position as shown. 

2) Attach Tape, Shield (X2) on to specified position. 

3) Next, wrap Sheet Core, E around area of Tape, Shield on AC power cord, to cover it.

4) Finally, install AC cord holder to AC power cord at specified position.

5) Attach Tape, Shield to AC power cord (X2) at specified position.

6) Attach Sheet Core, C to overlap the two Tape, Shields.

    

This is to prevent the Tape, Shields from peeling off.

Attach Tape, LCD to Connector Assy 10P and Connector Assy 14P as shown.

Use datum lines as an 

indication for attaching 

Tape, LCD to 

Connector Assy 14P 

 

 

Use datum lines as an indication for attaching

Tape, LCD to Connector Assy 10P 

Ferrite Core

Tape, Shield (X2)

Wrap Sheet Core, E around area of Tape, 

 Shield on AC Power Cord, to Cover it  

Attach Sheet Core, C to Tape, Shields. 

Make sure it overlaps the Tape, Shields. 

Attach Tape, Shield to AC Power Cord (X2)

Use edge of Inverter board's cover and AC power cord 

connector as a guideline for placement of power cord 

Portion of AC Power Cord with Sheet Core, E

When installing AC cord holder, make sure 

the Sheet Core, E area is clamped as well 

Attach Tape, LCD

(2X)

Dress Conn Assy 10P

below Frame, Spine 

Attach Tape, LCD (1X)

360 ± 5mm 

Ferrite Core

Tape, Shield (X2)

AC Cord Holder

Sheet Core, E

140± 5mm

285± 5mm

2

1

3

6

5

4

– 17 –

See steps below for LVDS harness and SP Connector Assy 4P wire dressing.

Note: When inserting LVDS harness to panel, make sure it is
          fully inserted and in the correct direction as shown.

1) Dress Connector Assy 10P into G1 bracket's hook (1X) as shown.

2) Next, dress Connector Assy 14P into G1 bracket's hook (4X).

 

CN3000

CN3000

CISPR model

Non-CISPR model

OK

NG

Conn Assy 10P is below G1 bracket

Keep distance between Conn 

Assy 10P and SP Conn Assy 4P

Dress Conn Assy 

10P into G1 bracket's 

hook (1X)

Attach Sheet Core, C

to LVDS harness.

LVDS harness

SP Conn Assy 4P below 

LVDS harness

SP Conn Assy 4P below 

LVDS harness

Screw earth clamps 

(2X)

LVDS harness

Dress Conn Assy 14P into G1 bracket's hook (4X)

2

1

– 18 –

1) Dress Connector Assy 13P into G1 bracket's hook as shown.
2) Align Connector Assy 14P, Connector Assy 10P and Connector
  Assy 13P together and dress them using Sheet Core, C.

1) Install AC cord holder to AC power cord at specified position as 
  shown.
2) Then install the AC power cord with holder into AC cord bracket.

1) Attach Sheet Core, C to Vesa Frame Bottom (32).
2) Insert AC power cord into CN6102.
3) Install the AC power cord with holder into Bracket, AC.
4) Then, install Bracket, AC into Bracket, Bottom.
5) Attach Sheet Core, C to Ferrite Core.
6) Lastly, dress AC power cord using pin, wire A6101 as shown.

80 ± 5mm 

Non-CISPR model

1

1. Ensure that AC power cord is not stressed 
  whilst inserting it into AC cord bracket.

CISPR model

Connecto
Assy 10P

Ferrite, Core

Bracket, AC

CAUTION:
1. Ensure that AC power cord is not stressed whilst
  inserting it into AC Cord bracket. 

Connector Assy 14P

Dress Conn Assy 13P into

G1 bracket's hook (1X)

Connector Assy 13P

AC cord bracket

Install AC power cord with

holder into AC cord bracket

Attach Sheet Core, C

to Vesa Frame Bottom (32)

Insert AC power
cord to CN6102.

Install AC power cord

with holder into 

Bracket, AC

Bracket, AC

Bracket, 
Bottom

Install Bracket, AC into Bracket, Bottom

AC Cord that is looped around

Ferrite Core is inserted under

Frame, Spine

Attach Sheet Core, C

to Ferrite Core

Dress AC power 

cord using pin, wire

A6101

Dress Conn Assy 14P, Conn 

Assy, 10P and Conn Assy 13P

using Sheet, Core, C

2

2

1

5

6

4

1

3

2

– 19 –

Hook the AC-band to the

rear cover.

Tie the root of the AC plug.