DOWNLOAD Sony KLV-26S550A / KLV-32S530A / KLV-32S550A / KLV-37S550A Service Manual ↓ Size: 5.51 MB | Pages: 72 in PDF or view online for FREE

– 16 –

 

OK

NG

2

w

 

 

 

1) Attach Sheet Core, C to frame bottom as shown.
2) Attach Sheet Core, C to main bracket as shown.
3) Insert Conn Assy 14P to inverter and GT3 PWB as shown. Attach Sheet Core, C as shown.

Note: When inserting LVDS harness to panel, make sure it is
 

fully inserted and in the correct direction as shown.

For all models
3) Attach Sheet Core, C to LVDS harness.
4) Attach Sheet Core, C to Connector Assy 14P and LVDS harness.

For CISPR models only
5) Insert screw on to earth clamp on LVDS harness.

 

 

 

1) Attach Sheet Core, C (X3) to main bracket as shown.
2) Attach Sheet Core, C (X1) to frame bottom as shown.
3) Attach Sheet Core, C (X1) to main bracket as shown.

Attach Sheet Core, C
to Main Bracket (X1).

CISPR model

Non-CISPR model

Attach Sheet Core, C (X1) to LVDS

harness.

Dress SP Conn

Assy 4P using

Sheet Core, C.

Attach Sheet Core, C to

Frame Bottom (X1).

Dress SP Conn Assy 4P; Lead

Assy, Earth and Conn Assy 10P

wires along this path (behind under

cover) and below raised area of

Frame Bottom.

Frame

Bottom

Dress Lead Assy, Earth

along this path

Attach Sheet Core, C (X1) to Conn Assy

14P and LVDS harness on frame spine.

Insert screw on to

earth clamp on LVDS

harness.

Attach Sheet Core, C (X1) to Conn

Assy 14P and LVDS harness on

frame spine.

Attach Sheet Core, C (X1) to

LVDS harness.

Dress SP Conn Assy 4P to

the left of this line (edge of

BT2 PWB)

Dress Conn

Assy 14P and

SP Conn Assy

4P together.

Dress Conn

Assy 10P and

SP Conn Assy

4P together.

Attach Sheet Core, C to

main bracket (X3).

Dress Lead Assy,

Earth to main bracket

using Sheet Core, C.

1

2

3

3

4

4

3

5

1

2

3

Dress SP Conn Assy 4P and

Conn Assy 10P together using

Sheet Core, C to frame bottom.

Insert Conn Assy 14P 

to GT3 PWB.

Attach Sheet Core, C (X1)

– 17 –

 

150 ± 5mm 

AC Cord Holder

 

 

110± 5mm

200 ± 5mm 

AC Cord
Holder

 

Ferrite 

Core

 

 

 

 

Non-CISPR model
1) Install AC cord holder to AC power cord at specified position as shown.
2) Then install the AC power cord with holder into under cover.
3) Lastly, dress AC power cord using pin, wire A6101 as shown.
4) Keep the AC power cord away from surrounding parts.

CISPR model
1) Install Ferrite core to AC power cord at specified position as shown.
2) Install AC cord holder to AC power cord at specified position as shown.
3) Then install the AC power cord with holder into under cover.
4) Attach Sheet Core, E to Ferrite Core. Place AC cord underneath frame spine.
5) Dress AC power cord using pin, wire A6101 as shown.
6) Lastly, keep the AC power cord away from surrounding parts.

Caution:
1. Ensure that AC power cord is not stressed whilst inserting it into
  AC cord bracket.

Caution:
1. Ensure that AC power cord is not stressed whilst inserting it into
  AC cord bracket.

Make sure distance of >4mm is kept

from F6102 and C6111 lead to single

insulated portion of AC power cord

(Blue and Brown wire). This can be

controlled by using pin, wire A6101 to

dress AC power cord away from

conductive parts.

Dress AC power cord using pin,

wire A6101. Keep AC cord away
from fuse F6102 (4mm or more).

Inset the AC Cord

Holder on to Under Cover.

Make sure distance of

>4mm is kept from F6102

and C6111 lead to single

insulated portion of AC

power cord (Blue and

Brown wire). This can be

controlled by using pin,

wire A6101 to dress AC

power cord away from

conductive parts.

Non-CISPR model

CISPR model

Dress AC power cord using

pin, wire A6101.

Attach Sheet Core,

E to Ferrite Core.

Insert the AC cord holder 

on to under cover

AC cord is

underneath frame

spine.

3

2

1

4

5

3

6

2

1

– 18 –

2

Non-CISPR model

1) Insert Connector Assy 10P to HT1 PWB. Attach HT1 PWB to Light Guide on Bezel.
2) Insert SP Conn Assy 4P to speaker as shown.
 

Attach Sheet Core, C (X1) as shown.

1) Insert Connector Assy 10P to SW unit. Attach SW unit to Bezel and dress with Tape (LCD) (X2).
2) Insert SP Conn Assy to speaker and attach Sheet Core, C as shown.
3) Attach Sheet Core, C to panel as shown.

CISPR model

Left speaker

Right speaker

Attach Sheet Core, C to SP Conn Assy 4P

and Conn Assy 10P to panel. Dress wires towards

bottom of panel as shown.

Dress SP Conn Assy 4P and Conn Assy 10P using Sheet Core, C.

Use datum line to position Sheet Core, C. Do not cover speaker hole

with Sheet Core, C.

Conn Assy 10P (HT1 PWB)

behind speaker

Attach Sheet Core, C to SP Conn Assy 4P and Conn 

Assy 10P. Use datum line to position Sheet Core, C. 

Do not cover speaker hole with Sheet Core, C.

Keep wire away from screw

hole --> Prevent wire from

being sandwiched by screw

when docking rear cover.

Dress Conn Assy 10P

(SW unit) using

Tape (LCD) (X2).

Conn Assy 10P (HT1 PWB)

behind speaker

1

2

3

1

Do not cover speaker hole

Do not cover
speaker hole

– 19 –

 

OK

NG

4

 

1) Attach Sheet Core, C (X3) to frame bottom as shown.
2) Insert Conn Assy 14P to inverter and G4T PWB as shown. Attach Sheet Core, C as shown.

For all models
3) Attach Sheet Core, C to LVDS harness.
4) Attach Sheet Core, C to Connector Assy 14P and LVDS harness on frame spine.

For CISPR models only
5) Insert screw on to earth clamp on LVDS harness.

Note:  When inserting LVDS harness to panel,
 

make sure it is fully inserted and in the

 

correct direction as shown.

1) Attach Sheet Core, C (X3) to main bracket as shown.
2) Attach Sheet Core, C (X1) to panel as shown.
3) Attach and screw Lead Assy, Earth on to G4T PWB as shown.
4) Attach Sheet Core, C (X1) to main bracket as shown.

Attach Sheet Core, C (X1)

to Conn Assy 14P and

LVDS harness.

Attach Sheet Core,

C to Lead Assy,

Earth on main

bracket.

Non-CISPR model

CISPR model

Attach Sheet Core, C to

frame bottom (X3).

Dress SP Conn Assy 4P and Conn Assy 10P 

wires along this path (behind under cover) and 

below raised area of bottom bracket.

Frame bottom

Do not cover screw

hole with Sheet 

Core, C

Insert Conn Assy 14P to

G4T PWB.

Attach Sheet Core, C (X1).

Attach Sheet Core, C

(X1) to LVDS harness.

Do not cover screw hole with 

Sheet Core, C. Keep LVDS harness 

away from screw hole.

Attach Sheet Core, C

(X1) to LVDS harness.

Attach Sheet Core, C (X1) to

Conn Assy 14P and LVDS

harness.

Insert screw on to earth

clamp on LVDS harness.

Do not cover screw hole with 

Sheet Core, C. Keep LVDS harness 

away from screw hole.

Dress Conn Assy 10P and

SP Conn Assy 4P together.

Attach and screw

Lead Assy, Earth.

Dress SP Conn Assy 4P

and Conn Assy 10P

together using Sheet 

Core, C to panel.

Attach Sheet Core, C

to main bracket (X3).

Attach Sheet Core, C to

Conn Assy 13P, Conn Assy
14P and SP Conn Assy 4P.

4

3

2

1

3

4

5

4

3

2

1

Dress SP Conn Assy

4P to the left of this line

(edge of BT2 PWB)