DOWNLOAD Sony KF-E42A10 / KF-E50A10 (serv.man7) Service Manual ↓ Size: 13.15 MB | Pages: 127 in PDF or view online for FREE

Apply CoFab conductive tape over black HPC cable. Tape P/n:2-

653-955-01

: Do not apply paper labels or stickers in area where

CoFab tape is to be applied. The tape MUST touch metal in all

areas contacting metal box.

Please minimize bubbles, creases, or gaps where tape contacts

metal box.

Install Pin-Plug Cable (from RF Bracket Assembly).

: Note the angle and direction of the Cable. Please ensure that 

there is minimal gap beween connection points. Look at slots on Pin-Plug 
connector to confirm the connector is pushed in as far as it can go (no gap). 
This is important for noise rejection and EMI.

Please Follow All 

points listed. It 

is important to control 
VARIATION of wire 
routing for minimizing 
Electro Maagnetic
Interference (EMI)

Wire routing/dressing of left side of B-Block.

:

-Note orientation of ferrite core – vertical
-Wires on 11P Conn. Assy. Are routed along

the metal shield case.

-Note 11P cable is looped  and held by 

M4 Clamp (one loop around wires).

:

Please Minimize wire routing/dressing variation. 
Reason: By following wire routing/dressing that
Is shown, EMI will be minimized.

:

Keep looped wire away from edge of bottom
Cabinet and screw boss pocket. This is a pinch
point that can damage the wires when rear
cover is installed.

Please Follow All 

points listed. It 

is important to control 
VARIATION of wire 
routing for minimizing 
Electro Maagnetic
Interference (EMI)

Connect B-Block Fan connector to CN8002 Pig-tail connector
on the AGA -Bd.

: Fan joint-connector is positioned in the middle

Between B-Block metal box and AGA-Bd.

Another view of left side of B-Block cable dressing.

:

Keep looped wire away from edge of bottom
Cabinet and screw boss pocket. This is a pinch
point that can damage the wires when rear
cover is installed.

:

-Note 

“DOT

” on LVDS Connector. Do not try to insert connector reversed.

-Note orientation of ferrite core – vertical
-Wires on 11P Conn. Assy. Are routed along

the metal shield case.

-Note 11P cable is looped  and held by 

M4 Clamp (one loop around wires).

Install Grounding strap (p/n:1-910-015-33) to top-right Metal Tab.

: Make sure terminal is “locked” in place after installation.

Make sure the back side 
of the B-Block is clear of 
pinch-points for cables 
before applying screws.

Apply 4x16mm screws to fix B-Block to Bottom Cabinet [4 places].
Screw p/n:2-580-640-01

Philips screwdriver

-[4x16mm screw]
- 13kg*cm +-1.0kg*cm

Install D.C. Fan (p/n:1-787-333-11), 3x8mm screw

[3places] p/n:2-580-593-01, fan shield p/n:2-593-086-

01, and fan dampers [qty=8] p/n:2-059-414-11 to

digital shield case (p/n:2-597-543-02)

: Make sure direction of fan is installed correctly. You should be 

able to see label with manufacurer and model of D.C. fan on opposite

side of digital shield case.

Install conductive gasket (p/n:2-653-452-01) on B-Bd

Ground pad (B-Side of PWB).

Install QG-Board with 3x8mm screw [5 places] on

DM Sheet Shield (p/n:2-597-541-03).

: No need QG-Shield plate over QG-Bd.

-Phillips Screw Driver

- 5kg-cm  +-0.5kg-cm

Please Follow All 

points listed. It 

is important to control 
VARIATION of wire 
routing for minimizing 
Electro Maagnetic
Interference (EMI)