Sony KF-50XBR800 / KF-60XBR800 Service Manual ▷ View online
– 9 –
KF-50XBR800/60XBR800
K
RM-Y912 RM-Y912
4. Self-Diagnosis screen displays
• In cases of malfunctions where it is not possible to determine the symptom such as when the power goes off occasionally or when the
screen disappears occasionally, there is a screen display on whether the malfunction occurred or not in the past (and whether the detection
circuit operated or not) in order to allow confirmation.
<Screen Display Method>
• Quickly press the remote command button in the following order from the standby state.
• Quickly press the remote command button in the following order from the standby state.
5. Self-Diagnosis Screen Display
• The results display is not automatically cleared. In case of repairs and after repairs, check the self-diagnosis screen and be sure to return
the results display to “ 0 ”.
• If the results display is not returned to “ 0 ” it will not be possible to judge a new malfunction after completing repairs.
<Method of Clearing Results Display>
<Method of Ending Self-Diagnosis Screen>
• When ending the self-diagnosis screen completely, turn the power switch OFF on the remote commander or the main unit.
• When ending the self-diagnosis screen completely, turn the power switch OFF on the remote commander or the main unit.
b
b ! b "#$
%&' (
)
* b #+,#$
, - .' / '&&
Self-Diagnosis screen display
J
Be aware that this differs from the method of
entering the service mode (volume + ).
DISPLAY b Channel 5 b VOL Ð b POWER
Self Diagnosis
B
b
SELF DIAGNOSIS
! " !
– 10 –
KF-50XBR800/60XBR800
K
RM-Y912 RM-Y912
6. Self-Diagnosis function operation
3 : Lamp Cover
When lamp cover SW is opened then pin 4 of CN1012 on the A board is high, LCD Engine µ-com (IC9502) detects
it and make turn off the lamp.
it and make turn off the lamp.
4 : FAN Stop
When FAN1 or FAN2 is stopped then pin 8 or q; of CN1012 on the A board is high, LCD Engine µ-com (IC9502)
detects it and make turn off the lamp.
detects it and make turn off the lamp.
5 : Lamp Driver
When lamp is not turned on then pin wl of LCD Engine µ-com (IC9502) is high, checks pin wk of LCD Engine µ-com
. If pin wk is low, it is judged no High Voltage.
. If pin wk is low, it is judged no High Voltage.
6 : Low B
Detect +5 V line failure.
9 : Audio
When DC is appeared by audio amp failure at speaker line.
Then it is detected by MAIN µ-com (IC9004) and it turns off the main power.
LAMP : Lamp error
When lamp is not turned on then pin wl of LCD Engine µ-com (IC9502) is high, checks pin wk of LCD Engine µ-com.
If pin wk is high, it is judged lamp is burned out.
If pin wk is high, it is judged lamp is burned out.
Self-Diagnosis block diagram
!
"
"
#
!
$
"
% &' ()
!
"
"
% " *'
% +,
-% .
/
01/2
$
0
1
1
$
– 11 –
KF-50XBR800/60XBR800
K
RM-Y912 RM-Y912
SECTION 2
DISASSEMBLY
2-1. REAR COVER ASSEMBLY
2-4. POWER BLOCK REMOVAL
2-2. OU BRACKET REMOVAL
2-3. SERVICE POSITION
2
1
1
1
Six screws
(+BVTP 4 x 16)
2
OU bracket
3
7
6
4
5
1
2
2
1
3
– 12 –
KF-50XBR800/60XBR800
K
RM-Y912 RM-Y912
2-6. UD BOARD, TERMINAL BOARD ASSEMBLY REMOVAL
2-5. OPTICAL UNIT BLOCK ASSEMBLY REMOVAL
1
Connector
1
Connector
3
2
5
RF antenna switch
4
Two washers
Nine screws
(+BVTP 3 x 12)
1
3
Screw
(+BVTP 4 x 16)
8
Two screws
(+BVTP 3 x 12)
Terminal board
assembly
Bracket M
6
2
7
UD board
9
Claw
Click on the first or last page to see other KF-50XBR800 / KF-60XBR800 service manuals if exist.