DOWNLOAD Sony KF-50XBR800 / KF-60XBR800 Service Manual ↓ Size: 10.86 MB | Pages: 127 in PDF or view online for FREE

MODEL

COMMANDER

DEST. CHASSIS NO.

––––––

 ––––––––––––

––––– –––––––––––

MODEL

COMMANDER

DEST. CHASSIS NO.

––––––

 ––––––––––––

––––– –––––––––––

KF-50XBR800

RM-Y912

US

KF-50XBR800

RM-Y912

Canadian

KF-60XBR800

RM-Y912

US

KF-60XBR800

RM-Y912

Canadian

RM-Y912

RM-Y912

KF-50XBR800/KF-60XBR800

– 2 –

Projection System

3 LCD Panels, 1 lens projection system

LCD Panel

1.35 inch TFT LCD panel Approx. 3.15 million dots (1,049,088 pixels)

Projection Lens

High Performance, large diameter hybrid lens F2.4

Antenna

75 ohm external terminal for VHF/UHF

Lamp

UHP lamp, 100W

XL-2000U

Television System

NTSC, American TV Standard

Screen Size (measured diagonally)

KF-50XBR800: 50 inches, KF-60XBR800: 60 inches

Channel Coverage

          VHF

2-13

          UHF

14-69

          CATV

1-125

Power Requirements

120V, 60 Hz

Number of Inputs/Outputs

          DVI-HDTV 1 terminal

3.3 V T.M.D.S., 50 ohms

The DVI-HDTV input terminal is compliant with the EIA-861 standard and is not intended for use

with personal computers.

          Video (IN)

4

1 Vp-p, 75 ohms unbalanced, sync negative

          S Video (IN)

3

Y: 1 Vp-p, 75 ohms unbalanced, sync negative

C: 0.286 Vp-p (Burst signal), 75 ohms

          Audio (IN)

6

500 mVrms (100% modulation)

Impedance: 47 kiloohms

          AUDIO (VAR/FIX)

1

500 mVrms at the maximum volume setting (Variable)

500 mVrms (Fixed)

Impedance (output): 2 kiloohms

          MONITOR OUT

1

 Video: 1 Vp-p 75 ohms unbalanced, Sync negative

Audio: 500 mVrms (100% modulation)

Impedance (output): 1 kiloohms

          CONTROL S (IN/OUT)

1

minijacks

          Component Video Input

2 (Y, PB , PR) Y: 1.0 Vp-p, 75 ohms unbalanced, sync negative

PB: 0.7 Vp-p, 75 ohms
PR: 0.7 Vp-p, 75 ohms

          RF Inputs

2

          Converter

1

Speaker Output

15 W 

× 2

Dimensions (W 

× H × D)

KF-50XBR800: 1,376 

× 964 × 415 mm (54 

1

/

4

 

× 38 × 16 

3

/

8

 inches)

KF-60XBR800: 1,618 

× 1,103 × 542 mm (63 

3

/

4

 

× 43 

1

/

2

 

× 21 

3

/

8

 inches)

Mass

KF-50XBR800: 50 kg (110 lb 4 oz), KF-60XBR800: 66 kg (145 lb 8 oz)

Power Consumption

          In Use

220 W

          In Standby

Under 1 W

Supplied Accessories

          Remote Control

RM-Y912

          AAA Batteries

2 supplied for remote control

          Cleaning Cloth

1

          Hex key wrench

1

          Brackets with screws

2

Optional Accessories

– 3 –

          TV Stand

SU-GW1

          Lamp

XL-2000U

          AV Cable

VMC-810/820/830 HG

          Audio Cable

RKC-515HG

          Control S Cable

RK-G69HG

          Component Video Cable

VMC-10/30 HG

          AV Receiver

STR-V555ES or equivalent

          Memory Stick media

8MB (MSA-8A), 16MB (MSA-16A), 32MB (MSA-32A), 64MB (MSA-64A),

128MB (MSA-128A)

                                                Design and specifications are subject to change without notice.

– 4 –

( US model only )

After correcting the original service problem, perfom the follow-

ing safety checks before releasing the set to the customer:

l.

Check the area of your repair for unsoldered or poorly-sol-
dered connections. Check the entire board surface for solder
splashes and bridges.

2. Check the interboard wiring to ensure that no wires are

“pinched” or contact high-wattage resistors.

3. Check that all control knobs, shields, covers, ground straps,

and mounting hardware have been replaced. Be absolutely
certain that you have replaced all the insulators.

4. Look for unauthorized replacement parts, particularly tran-

sistors, that were installed during a previous repair. Point them
out to the customer and recommend their replacement.

5. Look for parts which, through functioning, show obvious

signs of deterioration. Point them out to the customer and
recom mend their replacement.

6. Check the line cords for cracks and abrasion. Recommend

the replacement of any such line cord to the customer.

7. Check the condition of the monopole antenna (if any). Make

sure the end is not broken off, and has the plastic cap on it.
Point out the danger of impalement on a broken antenna to
the customer, and recommend the antenna’s replacement.

8. Check the B+ and HV to see they are at the values specified.

Make sure your instruments are accurate;be suspicious of
your HV meter if sets always have low HV.

9. Check the antenna temminals, metal trim, “metallized” knobs,

screws, and all other exposed metal parts for AC leakage.
Check leakage as described below.

The AC leakage from any exposed metal part to earth ground and

from all exposed metal parts to any exposed metal part having a
return to chassis, must not exceed 0.5mA (500 microampers) . Leak-
age current can be measured by any one of three methods.

1. A commercial leakage tester, such as the Simpson 229 or

RCA WT-540A. Follow the manufacturers’ instructions to
usc these instruments.

2. A battery-operated AC milliammeter. The Data Precision 245

digital multimeter is suitable for this job.

3. Measuring the voltage drop across a resistor by means of a

VOM or battery-operated AC voltmeter. The “limit” indica-
tion is 0.75V, so analog meters must have an accurate low-
voltage scale. The Simpson 250 and Sanwa SH-63Trd are
examples of a passive VOM that is suitable. NearIy all bat-
tery operated digital multimeters that have a 2V AC range
are suitable. (See Fig. A)

A cold-water pipe is guaranteed earth ground;the cover-plate re-

taining screw on most AC outlet boxes is also at earth ground. If
the retaining screw is to be used as your earth-ground, verify that it
is at ground by measuring the resistance between it and a cold-
water pipe with an ohmmeter. The reading should be zero ohms. If
a cold-water pipe is not accessible, connect a 60-l00 watts trouble
light (not a neon lamp) between the hot side of the receptacle and
the retaining screw. Try both slots, if necessary, to locate the hot
side of the line, the lamp should light at normal brilliance if the
screw is at ground potential. (See Fig. B)

1.5k Ω

1.5 µ F