Sony KDL-65HX729 Service Manual ▷ View online
KDL-65HX729
43
Components not identified by a part number or
description are not stocked because they are seldom
required for routine service.
The component parts of an assembly are indicated by the
reference numbers in the far right column of the parts list
and within the dotted lines of the diagram.
*
Items marked with an asterisk are not stocked since
they are seldom required for routine service. Expect
some delay when ordering these components.
NOTE: Les composants identifies per un trame et
une marque
!
sont critiques pour la securite.
Ne les remplacer que par une piece portant le
numero specifie.
NOTE: The components identified by shading
and
!
mark are critical for safety. Replace only
with part number specified.
NOTE: The components identified by a red outline and a mark contain
confidential information. Specific instructions must be adhered to whenever
these components are repaired and/or replaced.
See Appendix A: Encryption Key Components in the back of this manual.
SECTION 6 - DISASSEMBLY/PART NUMBER INFORMATION
TABLE-TOP STAND ASSEMBLY REMOVAL
A Remove 4 screws from Table-Top Stand Assembly
REF. NO.
PART NO.
DESCRIPTION
[ASSEMBLY INCLUDES]
REF. NO.
PART NO.
DESCRIPTION
[ASSEMBLY INCLUDES]
(Check the Sony Authorized Servicer Portal at
http://www.sony.com/asp
website for any additional service related issues.)
1
4-279-406-01
H, COVER(4L1)
2
4-279-407-01
HEAD BRACKET(4L1)
3
4-259-188-01
NECK(4L1)
4
4-285-741-01
STAND, BASE A(4L1)
5
7-685-648-79
SCREW +BVTP 3X12 TYPE2 IT-3
(SCREWS TO ATTACH HEAD COVER TO HEAD BRACKET)
6
4-268-126-02
SCREW, ORNAMENTAL M6X12
(SCREWS TO ATTACH HEAD STAND AND BASE STAND TO NECK)
7
2-580-608-01
SCREW, +PSW M5X16
(SCREWS TO ATTACH TABLE-TOP STAND TO LCD TV)
For product protection and safety reasons, Sony strongly recommends
that you use the screws provided with the TV
CAUTION: These screws cannot be used to secure the TV to
the Wall Mount Brackets
▲
2-580-608-01
SCREW, +PSW M5X16
(SCREWS TO ATTACH TABLE-TOP STAND TO LCD TV)
For product protection and safety reasons, Sony strongly recommends
that you use the screws provided with the TV
CAUTION: These screws cannot be used to secure the TV to
the Wall Mount Brackets
B Lift up TV set to detach from Table-Top Stand Assembly
C Gently place the LCD TV set face down onto a soft cloth
1
2
3
7
5
6
4
6
A
Soft Cloth
B
C
KDL-65HX729
44
Components not identified by a part number or
description are not stocked because they are seldom
required for routine service.
The component parts of an assembly are indicated by the
reference numbers in the far right column of the parts list
and within the dotted lines of the diagram.
*
Items marked with an asterisk are not stocked since
they are seldom required for routine service. Expect
some delay when ordering these components.
NOTE: Les composants identifies per un trame et
une marque
!
sont critiques pour la securite.
Ne les remplacer que par une piece portant le
numero specifie.
NOTE: The components identified by shading
and
!
mark are critical for safety. Replace only
with part number specified.
NOTE: The components identified by a red outline and a mark contain
confidential information. Specific instructions must be adhered to whenever
these components are repaired and/or replaced.
See Appendix A: Encryption Key Components in the back of this manual.
REAR COVER AND RU BOARD REMOVAL
CAUTION:
The Rear Cover is securely attached to the Bezel with cloth tape at the edges. Refer to
“Appendix A - Removing the Rear
Cover” on page A-1
for additional illustrations that show how to remove the Rear Cover.
Do not damage the Power Board Connector, Power Supply Cord. RU Connector, or Main Board when removing the Rear
Cover. Refer to
“Removing the Power Cord and the RU Connector” on page A-2
for complete instructions.
NOTES:
The Antenna Sheet (C EL), Antenna Cover (65), Label (BAT-V Rear) and Label (BAT-V Metal Side) are not included with the
Rear Cover and must be replaced when replacing the Rear Cover.
Steps A-C are specific for KDL-65HX729 Only and are only required if the RU Board needs to be repaired
A Press on the right side of the R Top Bracket then pull out to detach it from the R Bottom Bracket.
B Release clip to remove the RU Board from the R Bottom Bracket.
C Disconnect 1 connector from the RU Board.
CAUTION:
The Rear Cover for this model has some sharp edges. Refer to the illustration in
“Rear Cover Caution” on page
A-1
for information when handling the Rear Cover.
D Remove 21 screws from Rear Cover
E Remove 1 screw from Terminal Area position
F Remove 5 screws from Rear Cover
G Remove 4 screws from Rear Cover
H Remove 2 screws from Rear Cover
I Remove 1 screw from AC Cover
J Complete the following to remove the Rear Cover.
(For illustrations, refer to
“Appendix A - Removing the Rear Cover” on page A-1
)
1. Using a small flat-head screwdriver, push the tab to the right to lift out the Wireless Antenna Cover located on the bottom
right side of the Rear Cover.
2. Using gloves or a cloth for protection against the sharp edges, grasp the corner of the Rear Cover from inside the
Wireless Antenna Cover and lift up. (Refer to
“Removing the Power Cord and the RU Connector” on page A-2
)
3. After loosening the Rear Cover from the corner, you should be able to lift the bottom of the Rear Cover off of the Bezel.
Use caution not to damage the AC cord or the RS232 connector when lifting the Rear Cover from the Bezel.
4. After lifting the bottom of the Rear Cover, grasp the AC Power Cord while continuing to lift up the Rear Cover.
CAUTION: Do not pull the AC Power Cord or damage the connector the Power Supply Board.
5. Disconnect the AC Power Cord connector to detach it from the Power Supply Board.
NOTE: To release the AC Power Cord from the Rear Cover, release the clips on the inside of the AC Cover to detach it
from the Rear Cover.
6. This step is only required for models with an RU board
If the RU Board is still attached to the Rear Cover, when lifting the Rear Cover from the area around the RU Board
(located above the Terminal), disconnect the RS232 connector from the Main Board before fully removing the cover.
D
I
E
G
F
H
J
A
B
C
(Refer to the next page for part number information.)
KDL-65HX729
45
SECTION 6 - DISASSEMBLY/PART NUMBER INFORMATION
NOTE: Les composants identifies per un trame et
une marque
!
sont critiques pour la securite.
Ne les remplacer que par une piece portant le
numero specifie.
NOTE: The components identified by shading
and
!
mark are critical for safety. Replace only
with part number specified.
NOTE: The components identified by a red outline and a mark contain
confidential information. Specific instructions must be adhered to whenever
these components are repaired and/or replaced.
See Appendix A: Encryption Key Components in the back of this manual.
(Check the Sony Authorized Servicer Portal at
http://www.sony.com/asp
website for any additional service related issues.)
57
4-279-405-01
COVER, ANT(65)
58
4-268-431-11
SHEET, ANT (C EL)
59
4-266-269-01
COVER, AC(M)
△
4-256-393-01
SCREW, +PSW M3X6 W12
□
2-580-639-01
SCREW, +BVTP 4X12 TYPE2 IT-3
◆
4-257-907-01
JOINT, STAND
◇
4-268-126-02
SCREW, ORNAMENTAL M6X12
○
2-580-591-01
SCREW, +PSW M3X5
★
7-685-646-79
SCREW +BVTP 3X8 TYPE2 IT-3
51
4-269-369-12
BRACKET, R (BTM)
52
4-269-368-11
BRACKET, R (TOP)
53
A-1820-418-A
RU BOARD, MOUNTED
54
4-279-403-11
REAR COVER (65)A
55
4-256-437-01
LABEL (BAT-V METAL SIDE)
ORDER THIS PART WHEN REPLACING THE REAR COVER
56
4-265-028-01
LABEL (BAT-V REAR)
ORDER THIS PART WHEN REPLACING THE REAR COVER
54
52
53
51
59
55
56
57
58
REF. NO.
PART NO.
DESCRIPTION
[ASSEMBLY INCLUDES]
REF. NO.
PART NO.
DESCRIPTION
[ASSEMBLY INCLUDES]
KDL-65HX729
46
SECTION 6 - DISASSEMBLY/PART NUMBER INFORMATION
NOTE: Les composants identifies per un trame et
une marque
!
sont critiques pour la securite.
Ne les remplacer que par une piece portant le
numero specifie.
NOTE: The components identified by shading
and
!
mark are critical for safety. Replace only
with part number specified.
NOTE: The components identified by a red outline and a mark contain
confidential information. Specific instructions must be adhered to whenever
these components are repaired and/or replaced.
See Appendix A: Encryption Key Components in the back of this manual.
(Check the Sony Authorized Servicer Portal at
http://www.sony.com/asp
website for any additional service related issues.)
SWITCH UNIT, SPEAKERS AND WIRELESS LAN CARD REMOVAL
A Lift up Switch Unit and disconnect 1 connector to detach from Bezel
B Release clips and disconnect 1 connector to detach Power Switch from Switch Unit
C Lift up AC Power Cord and disconnect 1 connector to detach from LCD Panel
D Slide-out right side Speaker to detach from Bezel
D Slide-out right side Speaker to detach from Bezel
E Slide-out left side Speaker to detach from Bezel
F Remove 1 screw from Wireless LAN Card to detach from LCD Panel
G Remove 1 screw from Antenna to detach from WIFI Holder
H Remove 1 screw from WIFI Holder to detach from LCD Panel
I Remove 1 screw from Antenna to detach from WIFI Holder
J Remove 1 screw from WIFI Holder to detach from LCD Panel
K Remove 2 screws to detach Speaker Box Assembly from LCD Panel
!
101
1-798-348-11
POWER SWITCH
102
1-489-442-11
SWITCH UNIT
103
1-858-593-12
LOUDSPEAKER (3X15CM)
!
104
1-838-797-12
POWER-SUPPLY CORD (WITH CONN.)
REF. NO.
PART NO.
DESCRIPTION
[ASSEMBLY INCLUDES]
REF. NO.
PART NO.
DESCRIPTION
[ASSEMBLY INCLUDES]
105
1-458-355-11
WIRELESS LAN CARD
106
1-754-747-11
ANTENNA
107
1-754-750-11
ANTENNA
108
1-858-595-12
SPEAKER BOX ASSEMBLY (9X5CM)
△
4-256-393-01
SCREW, +PSW M3X6 W12
●
2-990-421-41
SCREW (+PSW) (M3X6)
102
101
103
103
104
105
106
Wifi
Bracket
Wifi
Bracket
107
108
A
B
D
E
C
F
I
J
G
K
H
Click on the first or last page to see other KDL-65HX729 service manuals if exist.