Sony KDL-55HX827 Service Manual ▷ View online
KDL-55HX827 59
SECTION 7 - SERVICE ADJUSTMENTS
5. To change the data value of the
BU_FLASH, press
3
to increase the data value to
1.
VPC
SERVICE
001
000
DATA_BAKUP
BU_FLASH 1
NOTE: If the message displays “
DATA TRANSFER NG
”
the transfer is not complete. If that occurs, repeat step
5
.
VPC
SERVICE
001
000
DATA_BAKUP
BU_FLASH 2
DATA TRANSFER NG
If successful, the data value changes to
3.
VPC
SERVICE
001
000
DATA_BAKUP
BU_FLASH 3
DATA TRANSFER SUCCESS
6. Verify the
Data Transfer Success message displays.
7. Proceed to “Confirming the Model ID and Product ID.”
CONFIRMING THE MODEL ID AND PRODUCT ID
After completing all of the service adjustment changes, verify that
the correct Model ID and Product ID displays in the Service menu.
Verify before proceeding to the next step:
Verify before proceeding to the next step:
;
Copied the BU Flash Data
8. Press
JUMP
or
OPTIONS
on the Remote Commander
until the
DIGITAL menu displays.
9. If necessary, press
4
to move to the
001 OP categor
DIGITAL
SERVICE
001 OP
000 VERS
---
<MAIN>
<EXT>
DM1.301W00AA
RF:01.05
WF1.003W00AA
WF:2.0.0.99
DF1.001W00AA
WF:0B
YM1.010W00AA
CAN:X.XXX
DB2.105W00AA
FDlXXXX
(DM1.301W00A)
DD1.016W00AA
WP0.521W00AA
<PEM>
MID:6D25E70B
PM1.012W00LU
PID:1003000
PB1.000W00LU
PNL:FQLL550LT0101
POP:X.XXX
PL1.011J46LUX
PD1.011J46LUX
KDL-55HX827 60
SECTION 7 - SERVICE ADJUSTMENTS
10. Using the information provided in the Segment Code
table below, verify the Model ID and Product ID are
correct.
Model Name Destination LCD Panel Code
Model-ID
Product-ID
KDL-55HX827
CO
FQLL550LT0101
6D25E70B
10030000
DIGITAL
SERVICE
001 OP
000 VERS
---
<MAIN>
<EXT>
DM1.301W00AA
RF:01.05
WF1.003W00AA
WF:2.0.0.99
DF1.001W00AA
WF:0B
YM1.010W00AA
CAN:X.XXX
DB2.105W00AA
FDlXXXX
(DM1.301W00A)
DD1.016W00AA
WP0.521W00AA
<PEM>
MID:6D25E70B
Model ID
Software Version
Panel ID
Product ID
PM1.012W00LU
PID:1003000
PB1.000W00LU
PNL:FQLL550LT0101
POP:X.XXX
PL1.011J46LUX
PD1.011J46LUX
11. Exit service mode by pressing
HOME
and then turn the
TV power off.
12. Cycle AC Power.
(Unplug and Plug AC Cord from the AC Outlet).
13. Wait a minute while lights flash, and initial setup screen
shows.
14. Proceed to “
Resetting the Panel Operation Time
”.
RESETTING THE PANEL OPERATION TIME
After completing all steps, reset the panel operation time from the Self
Check screen.
Verify before proceeding to the next step:
Verify before proceeding to the next step:
;
Copied the BU Flash Data
;
Confirmed Model ID and Product ID
1. TV must be in standby mode. (Power off).
2. Press the following buttons on the Remote Commander
within a second of each other:
DISPLAY
Channel
5
Volume
-
POWER
* NOTE: This differs from accessing Service Adjustments Mode
(Volume +)
Panel operation time
Panel operation time
-------------- -------------- -------------- 01
-------------- -------------- -------------- 00
-------------- -------------- -------------- 00
-------------- -------------- -------------- 00
-------------- -------------- -------------- 00
-------------- -------------- -------------- 00
002 MAIN_POWE
003 DC_ALERT
003 AUD_PROT
004 BALANCER
005 HFR_ERR
005 P_ID_ERR
12345-00333-06789
12345
-
00333
-
06789
-
-
-------------- -------------- -------------- 00
006 VLED
-------------- -------------- -------------- 00
005 TCON_ERR
-------------- -------------- -------------- 00
-------------- -------------- -------------- 00
-------------- -------------- -------------- 00
-------------- -------------- -------------- 00
006 BACKLITE
007 TEMP_ERR
010 EMITTER
-------------- -------------- -------------- 00
007 FAN_ERR
-------------- -------------- -------------- 00
012 IA
-------------- -------------- -------------- 00
SELF CHECK
-------------- -------------- -------------- 00
-------------- -------------- -------------- 00
101 VPC_WDT
-------------- -------------- -------------- 00
102 MEPS_WDT
-------------- -------------- -------------- 00
103 HOST_WDT
-------------- -------------- -------------- 00
104 STBY_WDT
-------------- -------------- -------------- 00
000 RGB_SEN
000 RESERVED
000 RESERVED
KDL-55HX827 61
SECTION 7 - SERVICE ADJUSTMENTS
3. To clear the LCD Panel operating hours of the LCD
Panel after replacing the panel, press
7
0
.
Panel operation time
Panel operation time
-------------- -------------- -------------- 01
-------------- -------------- -------------- 00
-------------- -------------- -------------- 00
-------------- -------------- -------------- 00
-------------- -------------- -------------- 00
-------------- -------------- -------------- 00
002 MAIN_POWE
003 DC_ALERT
003 AUD_PROT
004 BALANCER
005 HFR_ERR
005 P_ID_ERR
12345-00333-06789
12345
-
00333
-
00000
-
-
-------------- -------------- -------------- 00
006 VLED
-------------- -------------- -------------- 00
005 TCON_ERR
-------------- -------------- -------------- 00
-------------- -------------- -------------- 00
-------------- -------------- -------------- 00
-------------- -------------- -------------- 00
006 BACKLITE
007 TEMP_ERR
010 EMITTER
-------------- -------------- -------------- 00
007 FAN_ERR
-------------- -------------- -------------- 00
012 IA
-------------- -------------- -------------- 00
SELF CHECK
-------------- -------------- -------------- 00
-------------- -------------- -------------- 00
101 VPC_WDT
-------------- -------------- -------------- 00
102 MEPS_WDT
-------------- -------------- -------------- 00
103 HOST_WDT
-------------- -------------- -------------- 00
104 STBY_WDT
-------------- -------------- -------------- 00
000 RGB_SEN
000 RESERVED
000 RESERVED
4. Exit Self Check by pressing
HOME
and then turn the
TV power off.
5. Cycle AC Power.
(Unplug and Plug AC Cord from the AC Outlet).
OPTIONAL ADJUSTMENTS
All Sony TVs are set for optimal viewing performance. Refer to the
following instructions if the customer requests additional adjustments.
SETTING WHITE BALANCE ADJUSTMENTS
White Balance adjustment data is located on the Digital Service
Menu.
1. TV must be in standby Mode. (POWER off).
2. Press the following buttons on the Remote Commander
within a second of each other:
DISPLAY
Channel
5
Volume
+
POWER
DIGITAL
SERVICE
001 OP
000 VERS
---
<MAIN>
<EXT>
DM1.301W00AA
RF:01.05
WF1.003W00AA
WF:2.0.0.99
DF1.001W00AA
WF:0B
YM1.010W00AA
CAN:X.XXX
DB2.105W00AA
FDlXXXX
(DM1.301W00A)
DD1.016W00AA
WP0.521W00AA
<PEM>
MID:6D25E70B
PM1.012W00LU
PID:1003000
PB1.000W00LU
PNL:FQLL550LT0101
POP:X.XXX
PL1.011J46LUX
PD1.011J46LUX
KDL-55HX827 62
SECTION 7 - SERVICE ADJUSTMENTS
3. Press
JUMP
or
OPTIONS
on the Remote Commander
until the
VPC menu displays.
VPC
SERVICE
000
000
DATA_COPY
BU_TRANS 0
4. Press
2
to move to “006 WB” Category.
VPC
SERVICE
006
000
WB
R_DRV 128
5. To change the data value of the
R_DRV, press
3
to
increase the value or
6
to decrease the value.
NOTE: The data value must be set between the range
1 to 255.
6. Press
1
to move to the next item (
001 G_DRV).
7. To change the data value, press
3
to increase the
value or
6
to decrease the value.
8. Repeat steps 6 and 7 for each of the following items:
002 B_DRV
003 R_BKG
004 G_BKG
005 B_BKG
9. To save the changes, press
MUTING
then press
0
.
10. To exit service mode, press
HOME
or turn the TV
power off.
RESETTING THE TV TO FACTORY
CONDITION
Use the following instructions to restore the User Adjustments and
Channel Memory settings to the preset factory conditions.
1. Turn the TV On by pressing
POWER
.
2. While holding down the on the Remote Commander,
press the
POWER button on the side of the TV.
3. The set restarts and displays the Initial Setup screen.
This may take several minutes.
Click on the first or last page to see other KDL-55HX827 service manuals if exist.