Sony KDL-55HX827 Service Manual ▷ View online
KDL-55HX827
43
SECTION 6 - DISASSEMBLY/PART NUMBER INFORMATION
NOTE: The components identified by shading
and
!
mark are critical for safety. Replace only
with part number specified.
NOTE: The components identified by a red outline and a mark contain
confidential information. Specific instructions must be adhered to whenever
these components are repaired and/or replaced.
See Appendix A: Encryption Key Components in the back of this manual.
REF. NO.
PART NO.
DESCRIPTION
[ASSEMBLY INCLUDES]
REF. NO.
PART NO.
DESCRIPTION
[ASSEMBLY INCLUDES]
BATL (MAIN) BOARD AND
G6/G7 (POWER SUPPLY) BOARD REMOVAL
NOTES:
Refer to
“Handling the LVDS FFC Connector” on page 3
to disconnect the LVDS Connector.
The Insulation Sheet (G4), Insulation Sheet (G7), Sheet (BAT-L Metal Side) and Sheet (BAT-L Metal
Bottom) are not included with the LCD Panel and must be replaced when replacing the LCD Panel.
A Release 2 clips and slide-out Side Bracket to detach from BATL Board
B Release 2 clips and slide-out Bottom Bracket to detach from BATL Board
C Remove 6 screws from BATL Board
D Disconnect 4 connectors from BATL Board
(Refer to
“Handling the LVDS FFC Connector” on page 3
)
E Remove 4 screws from G6 Board
156
1-474-330-11
G6 BOARD, COMPLETE
157
4-268-443-01
SHEET, INSULATION (G4)
ORDER THIS PART WHEN REPLACING THE LCD PANEL
158
4-268-445-01
SHEET, INSULATION (G7)
ORDER THIS PART WHEN REPLACING THE LCD PANEL
159
1-474-305-11
G7 BOARD, COMPLETE
160
1-858-595-11
SPEAKER BOX ASSEMBLY (9X5CM)
4-256-393-01
SCREW, +PSW M3X6 W12
2-990-421-41
SCREW, (+PSW) (M3X6)
151
4-256-431-11
SHEET (BAT-L METAL SIDE)
ORDER THIS PART WHEN REPLACING THE LCD PANEL
152
4-256-432-11
SHEET (BAT-L METAL BOTTOM)
ORDER THIS PART WHEN REPLACING THE LCD PANEL
153
4-265-817-02
BRACKET SIDE (BAT-L METAL)
154
4-265-819-12
BRACKET BOTTOM (BAT-L METAL)
155
A-1822-793-A
BATL BOARD, COMPLETE
AFTER REPLACING THE MAIN BOARD OR THE LCD PANEL, YOU
MUST UPDATE THE SOFTWARE TO THE LATEST VERSION.
F Disconnect 7 connectors from G6
Board
G Remove 2 screws and disconnect 4
connectors from G7 Board
H Remove 3 screws and disconnect 1
connector from Woofer Box
156
159
160
155
154
153
157
158
152
151
F
B
A
E
G
H
D
C
KDL-55HX827
44
SECTION 6 - DISASSEMBLY/PART NUMBER INFORMATION
NOTE: The components identified by shading
and
!
mark are critical for safety. Replace only
with part number specified.
NOTE: The components identified by a red outline and a mark contain
confidential information. Specific instructions must be adhered to whenever
these components are repaired and/or replaced.
See Appendix A: Encryption Key Components in the back of this manual.
REF. NO.
PART NO.
DESCRIPTION
[ASSEMBLY INCLUDES]
REF. NO.
PART NO.
DESCRIPTION
[ASSEMBLY INCLUDES]
CENTER CABINET, HLT2 BOARD AND LCD PANEL REMOVAL
202
A-1792-920-A
HLT2 BOARD, MOUNTED
203
4-256-648-02
CENTER CABINET (55 POR)
4-256-393-01
SCREW, +PSW M3X6 W12
201
NA
LCD PANEL ASSEMBLY (P-MOD)
FOR ALL LCD PANEL AND TCON BOARD PART NUMBER INFORMATION
REFER TO THE LCD PANELS SERVICE MANUAL
CLEANING THE LCD PANEL
CAUTION: When cleaning the TV, be sure to unplug the power cord to avoid any chance of electric shock.
Clean the cabinet of the TV with a dry soft cloth.
Wipe the LCD screen gently with a soft cloth.
Stubborn stains may be removed with a cloth slightly moistened with a solution of mild soap and warm water.
If using a chemically pretreated cloth, please follow the instruction provided on the package.
Never use strong solvents such as a thinner, alcohol or benzine for cleaning.
Periodic vacuuming of the ventilation openings is recommended to ensure to proper ventilation.
CAUTIONS:
When replacing the LCD Panel
Assembly refer to
”Special Handling
Instructions When Replacing the LCD
Panel Assembly” on page 5
.
The HLT2 Board is attached to the
LCD Panel with PWB (H) Tape. Do
NOT damage the HLT2 Board when
removing from the LCD Panel.
A Remove 7 screws from Center Cabinet
to detach from LCD Panel
B Carefully lift-up HLT2 Board to detach
from LCD Panel
203
202
201
PWB (H)
Tape
A
B
PWB (H)
Tape
KDL-55HX827
45
SECTION 6 - DISASSEMBLY/PART NUMBER INFORMATION
NOTE: The components identified by shading
and
!
mark are critical for safety. Replace only
with part number specified.
NOTE: The components identified by a red outline and a mark contain
confidential information. Specific instructions must be adhered to whenever
these components are repaired and/or replaced.
See Appendix A: Encryption Key Components in the back of this manual.
251
1-838-923-11
CONNECTOR ASSEMBLY
*
252
1-838-919-11
CONNECTOR ASSEMBLY 2P
*
253
1-838-920-11
CONNECTOR ASSEMBLY 2P
*
254
1-910-801-45
CONNECTOR ASSEMBLY 7P
255
1-910-801-29
CONNECTOR ASSEMBLY 14P
SCREWS
REF. NO.
PART NO.
DESCRIPTION
[ASSEMBLY INCLUDES]
REF. NO.
PART NO.
DESCRIPTION
[ASSEMBLY INCLUDES]
256
1-910-802-21
CONNECTOR ASSEMBLY 28P
* 257
1-838-805-11
(LVDS) FLEXIBLE FLAT CABLE Y2 55S
*
258
1-910-802-14
HARNESS ASSEMBLY
251
252
253
254
255
256
257
258
CONNECTORS
P/N
DESCRIPTION
REMARKS
TOTAL
▲ 2-580-608-01
SCREW, +PSW M5X16
TABLE-TOP STAND(3)
3
△ 4-256-393-01
SCREW, +PSW M3X6 W12
AC CVR(1), WOOFER(3), CNTR CBNT(7)
9
□ 2-580-639-01
SCREW, +BVTP 4X12 TYPE2 IT-3
RC(4)
4
◆ 4-257-907-01
JOINT, STAND
RC(2)
2
◇ 4-268-126-02
SCREW, ORNAMENTAL M6X12
RC(6)
6
● 2-990-421-41
SCREW (+PSW) (M3X6)
BATL(6), G6(4), G7(2), WIFI(1), ANTENNAS(2), CAMERA(1)
16
○ 4-258-272-01
SCREW, +PWH M3X8
RC(11), SWITH UNIT(1)
12
★ 7-685-646-79
SCREW +BVTP 3X8 TYPE2 IT-3
TRMNL BRKT(2), SIDE BRKT(1)
3
☆ 4-259-541-01
USER SCREW ST
HEAD STAND to NECK(1), NECK to BASE STAND(3)
4
KDL-55HX827
KDL-55HX827
46
SECTION 6 - DISASSEMBLY/PART NUMBER INFORMATION
ACCESSORIES AND PACKAGING
3-299-071-05
FLYER, SAFETY
4-273-074-11
FLYER, SAFETY
4-273-016-33
MANUAL, INSTRUCTION
*
4-270-904-11
SUPPLEMENT(STAND INSTALLATION)
MISCELLANEOUS
X-2560-379-1
BAG, SCREW ASSEMBLY (L)
CONTAINS THE FOLLOWING SCREWS
4-259-541-01
USER SCREW ST
(SCREWS TO ATTACH HEAD STAND AND BASE STAND TO NECK)
2-580-608-01
SCREW, +PSW M5X16
(SCREWS TO ATTACH TABLE-TOP STAND TO LCD TV)
For product protection and safety reasons, Sony strongly recommends
that you use the screws provided with the TV
CAUTION: These screws cannot be used to secure the TV to
the Wall Mount Brackets
1-838-791-11
CABLE CONVERSION (VIDEO/COMPONENT ADAPTOR)
4-262-708-01
CLAMPER, CABLE
4-257-907-01
JOINT, STAND
(SCREWS USED WHEN STAND IS ATTACHED-NOT USED WITH WALL MOUNTS)
4-256-443-01
SHEET, RADIATION (BAT-L/V)
ORDER THIS PART WHEN REPLACING THE LCD PANEL
4-256-454-02
SPACER (G A)
X-2580-498-1
SUPPORT BELT KIT
4-195-059-21
TAPE, PWB (H)
OPTIONAL ACCESSORIES
THE 3D GLASSES LISTED BELOW ARE AVAILABLE THROUGH THE SONY STYLE WEBSITE.
USE THE DESCRIPTION TO LOCATE THE PART AND PRICEING INFORMATION.
TDG-BR50/B
3D GLASSES (BLACK - SIZE SMALL)
TDG-BR50/P
3D GLASSES (PINK - SIZE SMALL)
TDG-BR50/L
3D GLASSES (BLUE - SIZE SMALL)
TDG-BR100/B
3DGLASSES (BLACK - SIZE ADULT)
TDG-BR200/B
3D GLASSES (SIZE SMALL)
TDG-BR250/B
3D GLASSES (SIZE ADULT)
TDG-BR250/DBL 3D GLASSES - TWO PACK
4-289-288-01
LID, BATTERY COVER FOR 3D GLASSES
1-458-395-21
POLARIZER ADAPTER (FOR BR200 MODEL)
1-458-395-11
POLARIZER ADAPTER (FOR BR250 MODEL)
1-838-940-11
USB CABLE
SU-WH500
WALL HANGING BRACKET
SU-WL500
WALL MOUNTING BRACKET
SU-WL700
WALL MOUNTING BRACKET
REMOTE COMMANDER
1-489-464-11
REMOTE COMMANDER (RM-YD058)
Click on the first or last page to see other KDL-55HX827 service manuals if exist.