Sony KDL-46HX855 / KDL-55HX855 (serv.man2) Service Manual ▷ View online
KDL-46HX855/55HX855 vi
CAUTIONS AND WARNINGS
SAFETY CHECK-OUT
After correcting the original service problem, perform the following safety
checks before releasing the set to the customer:
1. Check the area of your repair for unsoldered or poorly soldered
connections. Check the entire board surface for solder splashes
and bridges.
2. Check the interboard wiring to ensure that no wires are “pinched” or
touching high-wattage resistors.
3. Check that all control knobs, shields, covers, ground straps, and
mounting hardware have been replaced. Be absolutely certain that
you have replaced all the insulators.
4. Look for unauthorized replacement parts, particularly transistors,
that were installed during a previous repair. Point them out to the
customer and recommend their replacement.
5. Look for parts which, though functioning, show obvious signs of
deterioration. Point them out to the customer and recommend their
replacement.
6. Check the line cords for cracks and abrasion. Recommend the
replacement of any such line cord to the customer.
7. Check the antenna terminals, metal trim, “metallized” knobs,
screws, and all other exposed metal parts for AC leakage. Check
leakage as described in “Leakage Test”.
LEAKAGE TEST
The AC leakage from any exposed metal part to earth ground and from all
exposed metal parts to any exposed metal part having a return to chassis,
must not exceed 0.5 mA (500 microamperes). Leakage current can be
measured by any one of three methods.
1. A commercial leakage tester.
Follow the manufacturers’ instructions provided with the tester.
2. A battery-operated AC milliammeter.
3. Measuring the voltage drop across a resistor by means of a VOM
or battery-operated AC voltmeter. The “limit” indication is 0.75 V, so
analog meters must have an accurate low voltage scale. Nearly all
battery-operated digital multimeters that have a 2 VAC range are
suitable. (see Figure A)
To Exposed Metal
Parts on Set
0.15 µF
Earth Ground
AC
Voltmeter
(0.75V)
Figure A. Use an AC voltmeter to check AC leakage.
HOW TO FIND A GOOD EARTH GROUND
The cover-plate retaining screw on most AC outlet boxes is at earth ground.
Verify the AC outlet box retaining screw ground by connecting a 60W to
100W incandescent (not a neon or fluorescent lamp) between the hot side of
the receptacle and the retaining screw. Try both slots, if necessary, to locate
the hot side on the line; the lamp should light at normal brilliance if the screw
is at ground potential. (see Figure B)
Figure B. Checking for earth ground.
Trouble Light
AC Outlet Box
KDL-46HX855/55HX855 1
FEATURES
The AZ3F chassis is one of several designs for the 2012 model line of Sony
Bravia® LCD televisions. This manual covers the following models:
KDL-46HX855
KDL-55HX855
KDL-46HX855
KDL-55HX855
The BRAVIA® HX855 series features a truly transcendent picture quality,
each scene in everything you watch—HD movies, 3D, sports, even
YouTube™ clips—is presented with unprecedented detail and astonishing
color from Sony’s exclusive X-Reality™ PRO picture engine. Ultra-clear,
realistic motion during slow scenic sweeps and fast action sports comes
courtesy of Motionflow™ XR 960.
●
Pro-grade detail for discerning eyes: X-Reality™ PRO
●
Experience precise motion clarity with Motionflow™ XR 960
●
Frameless design with Corning’s Gorilla® Glass
●
Movies, music & apps with Sony Entertainment Network
1
●
Amazingly crisp, natural 3D effects in every 3D scene
2
●
Dynamic Edge LED backlight for amazing contrast & color
●
Stream HD entertainment wirelessly with built-in Wi-Fi®
1
●
PC and tablet content
3
on your TV with Intelligent Connect
●
Make life-sized video calls with Skype®
1
●
Media Remote™ app to control your TV with a smartphone
4
●
Connect to the TV via Wi-Fi® without using a router
3
SECTION 1 - FEATURES AND OVERVIEW
SPECIFICATIONS
Sistema
:
o: NTSC 3.58 / PAL-M / PAL-N
g
o
l
á
n
A
V
T
e
d
a
m
e
t
s
i
S
Digital: SBTVD
Cobertura de canales
CATV (Análogo): 1-135
Sistema del panel
Salida de bocinas
Salida de bocinas
Tomas de entrada/salida
CABLE/ANTENNA
(Cable/Antena)
(Cable/Antena)
Terminal externa de 75 ohms para entrada de señal de radiofrecuencia
VIDEO IN 1
(Entrada de video 1)
Entrada de video/audio (izquierda-derecha)
COMPONENT IN
(Entrada de componente)
VIDEO IN 2
(Entrada de video 2)
YP
B
P
R
(video componente): 1080p (50, 60 Hz), 1080i (50, 60 Hz),
1720p (50, 60 Hz), 576p, 576i, 480p, 480i
Entrada de audio (izquierda-derecha)
Entrada de video (contacto común de componente)
Entrada de video (contacto común de componente)
HDMI IN 1/2/3/4
(Entrada HDMI 1/2/3/4)
(Entrada HDMI 1/2/3/4)
Video (2D): 1080p (30, 50, 60 Hz), 1080/24p, 1080i (50, 60 Hz),
720p (30, 50, 60 Hz), 720/24p, 576p, 576i, 480p, 480i,
Formatos de PC
Video (3D):
Estructuración de imágenes 1080p (30 Hz), 1080/24p, 1080i (50, 60 Hz),
Estructuración de imágenes 1080p (30 Hz), 1080/24p, 1080i (50, 60 Hz),
720p (30, 50, 60 Hz), 720/24p
Una a lado de otra 1080p (50, 60 Hz), 1080/24p, 1080i (50, 60 Hz),
720p (30, 50, 60 Hz)
Una arriba de otra 1080p (30, 50, 60 Hz), 1080/24p, 1080i (50, 60 Hz),
720p (50, 60 Hz)
Audio: PCM lineal de dos canales: 32; 44,1 y 48 kHz, 16, 20 y 24 bits,
Dolby Digital
Entrada de audio analógico (minitoma estéreo)
(sólo HDMI IN 2, común con PC IN (entrada de PC))
ARC (sólo HDMI IN 1)
(sólo HDMI IN 2, común con PC IN (entrada de PC))
ARC (sólo HDMI IN 1)
AUDIO OUT
(Salida de audio)/Auriculares
Minitoma estéreo
DIGITAL AUDIO OUT (OPTICAL)
Toma óptica digital (PCM lineal de dos canales, Dolby Digital)
Speaker Integrated Stand
(Base con Altavoz Integrado)
(Base con Altavoz Integrado)
Salida de sonido para el soporte para TV
PC IN (Entrada de PC)
PC/HDMI 2 AUDIO IN
(Entrada de audio de PC/HDMI 2)
RGB analógico (Conector D-sub de 15 pines)
Entrada de audio (minitoma estéreo) (común con HDMI IN 2)
Entrada de audio (minitoma estéreo) (común con HDMI IN 2)
X
T
-
E
S
A
B
0
0
1
/
T
-
E
S
A
B
0
1
r
o
t
c
e
n
o
C
N
A
L
n
e
r
a
ir
a
v
a
ír
d
o
p
n
ó
i
x
e
n
o
c
a
l
e
d
d
a
d
i
c
o
l
e
v
a
L
(
función del entorno de red. No se garantizan la tasa de comunicación
ni la calidad de comunicación 10BASE-T/100BASE-TX para este TV.)
ni la calidad de comunicación 10BASE-T/100BASE-TX para este TV.)
.
e
l
b
it
a
p
m
o
c
o
t
a
m
r
o
f
l
e
a
r
a
p
l
a
u
n
a
M
-i
l
e
e
tl
u
s
n
o
C
A
N
L
D
/
B
S
U
VHF: 2-13, UHF: 14-69
10 W + 10 W + 10 W
Panel LCD (pantalla de cristal líquido)
1. Broadband speed of at least 2.5 Mbps recommended (10 Mbps for HD). Content subject to
change and may require fees. Skype requires CMU-BR100 camera sold separately. Subject
to Skype’s terms and conditions.
2. Requires 3D content, 3D player, HDMI® cable (at least 10.2 Gbps) and 3D active glasses
sold separately.
3. Streaming content, copy-protected content and certain formats are not supported.
4. Requires devices connected to the same wireless home network.
4. Requires devices connected to the same wireless home network.
KDL-46HX855/55HX855 2
SECTION 1 - FEATURES AND OVERVIEW
* El tamaño, las dimensiones y el peso de la pantalla son valores aproximados.
•
La disponibilidad de los accesorios opcionales dependerá de los países, regiones, modelo del TV
y de las existencias.
•
El diseño y las especificaciones están sujetos a cambios sin previo aviso.
Nombre del modelo KDL-
55HX85x
46HX85x
Alimentación y otras especificaciones
Requisitos de alimentación
Consumo de
potencia
Consumo de
potencia
W
9
1
1
W
7
4
1
o
s
u
n
e
en espera
en espera
Tamaño de pantalla*
(cm)
(medido diagonalmente)(pulgadas)
138,8
54,6
(55 clase)
54,6
(55 clase)
116,8
46
46
Resolución del monitor
Dimensiones*
Dimensiones*
8
6
2
×
7
9
6
×
7
7
0
.
1
1
4
3
×
8
0
8
×
4
7
2
.
1
)
m
m
(
e
t
r
o
p
o
s
n
o
c
5
3
×
0
4
6
×
7
7
0
.
1
5
3
×
0
5
7
×
4
7
2
.
1
)
m
m
(
e
t
r
o
p
o
s
n
i
s
patrón de orificios de
montaje mural (mm)
patrón de orificios de
montaje mural (mm)
300 × 300
tamaño de tornillos
de montaje mural
de montaje mural
(mm)
M6 (longitud: consulte el Manual de instrucciones.)
3
,
0
2
2
,
6
2
)
g
k
(
e
t
r
o
p
o
s
n
o
c
*
o
s
e
P
6
,
6
1
7
,
1
2
)
g
k
(
e
t
r
o
p
o
s
n
i
s
Accesorios suministrados
Consulte el Manual de instrucciones.
Accesorios opcionales
Soporte para TV: SU-B553S (KDL-55HX85x)
SU-B463S (KDL-46HX85x)
Gafas 3D: TDG-BR750/TDG-BR250/TDG-BR200/TDG-BR100/TDG-BR50
Unidad de cámara y micrófono: CMU-BR100
Adaptador de LAN inalámbrica USB: UWA-BR100
Unidad de cámara y micrófono: CMU-BR100
Adaptador de LAN inalámbrica USB: UWA-BR100
Temperatura de funcionamiento
110-240 V ca, 50/60 Hz
Menos de 0,3 W
1.920 puntos (horizontal) × 1.080 líneas (vertical)
Soporte de montaje mural: SU-WL500
0 ºC – 40 ºC
CHECKING THE ACCESSORIES
Control remoto (1)*
1
Pilas de tamaño AAA (2)
Soporte de sobremesa (1)*
Soporte de sobremesa (1)*
2
Tornillos de fijación para el soporte de
sobremesa (M5 × 16) (3)
Tornillos de montaje para el soporte de
sobremesa (M5 x 16) (4)
Manual de instrucciones (este manual) y
otros documentos
sobremesa (M5 × 16) (3)
Tornillos de montaje para el soporte de
sobremesa (M5 x 16) (4)
Manual de instrucciones (este manual) y
otros documentos
*
1
Consulte el número del modelo impreso en el
control remoto.
*
2
Se requiere ensamblar la base de soporte de
sobremesa. Para ensamblar la base de soporte
de sobremesa consulte el folleto suministrado.
KDL-46HX855/55HX855 3
SECTION 1 - FEATURES AND OVERVIEW
CHASSIS OVERVIEW
The primary circuits in the AZ3F chassis consist of a Main Board (BAPS Board), Power Supply Board (G6 Board for the 46” models, and G7 Board for the 55”
models), the IR Board (HL Board), the 3D IR Emitter (HEM3 Board), the Wireless LAN Card, the Switch Unit, and the LCD Panel assembly which includes the
TCON Board.
NOTE: For connector part number information, refer to
NOTE: For connector part number information, refer to
“Connectors” on page 24
. For Wire Dressing information, refer to
“Wire Dressing” on page 26
.
SWITCH
UNIT
HL
HEM3
TCON
G6
BAPS
WIRELESS
LAN CARD
BOARD LAYOUT FOR KDL-46HX855 ONLY
SWITCH
UNIT
HL
HEM3
TCON
G7
BAPS
WIRELESS
LAN CARD
BOARD LAYOUT FOR KDL-55HX855 ONLY
Click on the first or last page to see other KDL-46HX855 / KDL-55HX855 (serv.man2) service manuals if exist.