DOWNLOAD Sony KDL-40Z5500 / KDL-40Z5710 / KDL-46Z5500 / KDL-52Z5500 Service Manual ↓ Size: 7.16 MB | Pages: 76 in PDF or view online for FREE

To install the ‘Rear Cover’ push the clamper point as shown 
in the photo on the back surface of the ‘Rear Cover’ then 
replace all screws.

Remove the 4 stand fixing screws indicated and lift the TV 
set up and away from the ‘Stand Assy’.

Screw Part number(s) and Description(s)

2-580-608-01    SCREW, +PSW M5X16

=>=>

=>

=>

Clamper Here

Push This
Point

To remove the ‘Stay Top’ place a flat blade screwdriver as 
shown by 1 in the photo above, then lift the clamper slightly 
as shown by 2 and finally slide the clamper as shown by 3.
When reusing the ‘Stay Top’ please use with the removed 
set.

1

2

3

1

2

To install the ‘Stay Top’ slide into place as shown by 1 in the 
photo above, then push the clamper as shown by 2, making 
sure that the embossing on the clamper is locked in the hole 
of the panel.

     Screws

Screw Part number(s) and Description(s)

2-580-592-01  SCREW, +PSW M3X8

To remove the ‘D1N/D3N’ board disconnect all the
connectors and then remove the 2 screws circled and ease the 
board gently away from the back of the TV set.

Note: Refer to page 4 - Hirose MDF61 connector.

To remove the ‘G6NS/G7NS’ board disconnect all the
connectors and then remove the 4 screws circled and ease 
the board gently away from the back of the TV set.

Screw Part number(s) and Description(s)

2-580-592-01  SCREW, +PSW M3X8

     Screws

To remove the ‘Loudspeakers’ first disconnect the speaker 
cables and then remove the screws circled.  

Screw Part number(s) and Description(s)

(a) 2-580-592-01    SCREW, +PSW M3X8
(b) 2-580-640-01    SCREW, +BVTP2 4X16

To remove the ‘Switch Unit’ push the top of the unit in the 
shaded area in the photo and rotate in the direction of the
arrow. Then repeat the procedure on the bottom of the unit.

Push

Push

     Clip

To remove the ‘HL1A’ board disconnect the connector and 
then release the 2 clips circled and ease the board gently 
away from the back of the TV set.

     Clips

To remove the ‘BA’ board disconnect all the connectors and 
then remove the 8 screws circled and ease the board gently 
away from the back of the TV set.

     Screws

       Screws

Screw Part number(s) and Description(s)

2-580-592-01    SCREW, +PSW M3X8

Screw Part number(s) and Description(s)

2-580-592-01  SCREW, +PSW M3X8

To remove the ‘D2N/D4N’ board disconnect all the
connectors and then remove the 2 screws circled and ease the 
board gently away from the back of the TV set.

Note: Refer to page 4 - Hirose MDF61 connector.

     Screws

To remove the ‘HSN’ board disconnect the connector and 
then release the 1 clip circled and ease the board gently 
away from the back of the TV set.

I/

TV

i+

5

+

(ON SCREEN                            (DIGIT 5)                                (VOLUME +)                                  (TV)
   DISPLAY)

Service adjustments to this model can be performed using the
supplied Remote Commander RM-ED019. 

3.  The TVM menu appears on the screen (See Pic.1).



After carrying out the service adjustments, to prevent the  

 

customer accessing the ‘Service Menu’ switch the TV set OFF 

 

and then ON.

1.  Turn on the power to the TV set and enter into the stand-by
 

mode.

2.  Press the following sequence of buttons on the Remote 
 

Commander.

1.  Press “2 / 5” on the remote commander to select (up / down)
 

category (See Pic.2).

2.  Press “1 / 4” on the remote commander to select (up / down)
 

item (See Pic.2).

3.  Press “3 / 6” on the remote commander to select (up / down)
 

data (See Pic.2).

1.  Press “Mute” on the remote commander. The word “SERVICE”
 

changes to “WRITE” (See Pic.3).

Data

Category

Item

2.  Press “0” on the remote commander. The word “WRITE”
 

changes to red. This indicates writing is in progess. (See Pic.4).

3.  When red “WRITE” changes to green “SERVICE”.
 

This indicates writing is complete. (See Pic.5).