DOWNLOAD Sony KDL-40Z4500 / KDL-46Z4500 / KDL-52Z4500 (serv.man3) Service Manual ↓ Size: 7.12 MB | Pages: 51 in PDF or view online for FREE

– 32 –

– 33 –

Service adjustments to this model can be performed using the
supplied Remote Commander RM-GD005.
(TV must be in analogue mode).

1.

Turn on the power to the TV set and enter into the stand-by
mode.

2.

Press the following sequence of buttons on the Remote
Commander.

3.

The following menu appears on the screen (See Pic.1).

4.

Move to the corresponding adjustment item using the
‘

R

 ’ or ‘

r

 ’ arrow buttons on the Remote Commander.

5.

Press the ‘

t

 ’ arrow button to enter into the required menu

item.

6.

Adjust the data value using the ‘

R

’ or ‘

r

’ arrow buttons on

on the Remote Commander.

7.

To go back at any time press the ‘Return’ button on the
Remote Commander.

8.

Press the ‘Menu’ button on the Remote Commander to quit
the Service Mode when all adjustments have been
completed.

Note:

•

To place the Remote Commander in ‘Service Mode’ press
the following buttons together for approximately two
seconds.

•

To use the Remote Commander in ‘Service Mode’ press
the BD/DVD/AMP standby button on the Remote
Commander twice.

TT will then appear in the bottom right hand corner of the TV.

i+

5

+

(ON SCREEN                            (DIGIT 5)                                (VOLUME +)                            (TV POWER)
   DISPLAY)

i+

5

+

(ON SCREEN                            (DIGIT 5)                                (VOLUME +)                       
   DISPLAY)

TT Button

•

To take the Remote Commander out of ‘Service Mode’
press the same buttons above together again for two
seconds or remove thebatteries from the Remote
Commander.

•

After carrying out the service adjustments, to prevent the
customer accessing the ‘Service Menu’ switch the TV set
OFF and then ON again.

1.

The following menu appears on the screen when you enter
the ‘Product Version’ menu (See Pic.2). Be sure to check
all pages.

1.

The following menu appears on the screen when you enter
the ‘Service Config’ menu (See Pic.3).

– 34 –

1.

The following menu appears on the screen when you enter
the ‘White balance’ menu (See Pic.7).

1.

The following menu appears on the screen when you enter
the ‘Error Menu’ menu (See Pic.8). Be sure to check all
pages.

1.

The following menu appears on the screen when you enter
the ‘Set-up’ menu (See Pic.4). Be sure to check all pages.

1.

The following menu appears on the screen when you enter
the ‘Sound’ menu (See Pic.5).

1.

The following menu appears on the screen when you enter
the ‘IF Adjust’ menu (See Pic.6).

– 35 –

TT mode is available by setting the TV and Remote Commander
for operation in Service Mode [ As shown on Page 33 ]. The
functions described below are then available by selecting the
two numbers. To release the ‘TT mode’ press 00. To release the
TT menu press the menu key.

00

‘TT’ mode off

03

Set volume to 35%

04

Set volume to 50%

05

Set volume to 65%

06

Set volume to 80%

07

Ageing mode on

08

Shipping Condition

09

WB adj initial condition

19

Factory mode toggle (on/off)

25

40" FHD//EM model

26

46" FHD//EM model

27

CBA mode toggle (ON/OFF)

31

ECS mode toggle (ON/OFF)

32

Set BCN channels preset

34

HDMI log enable/disable

35

Hotel mode toggle

38

OTRUM mode toggle

39

Enable digital test

41

Re-initialise NVM

43

Select Dual Sound A

44

Select Dual Sound B

45

Select Dual Sound Mono

46

Select Dual Sound Stereo

48

Set NVM as non-virgin

49

Set NVM as virgin

54

Watchdog toggle

57

Gemstar Service Mode (EG1L)

58

Reset package version

59

Visual I2C toggle (VCT micro slave mode)

61

Set 52" FHD//EM model

69

WXGA/FHD panel selection

71

Auto AGC

72

VESA/JEIDA panel selection

73

HDMI number of inputs (0 to 2)

74

DDC enable

75

Set centred balance

76

Set volume to max

77

Set volume to min

78

Set balance full left

79

Set balance full right

81

Digital BER display

82

Digital Service menu

83

Digital colour bar output from DENC

84

TS CI path through

85

Digital tuner power down (Only one power cycle,

default is no power down)

86

Switch between two digital SW banks

87

Local keys test

88

Digital shipping conditions (Clear tune database)

89

LED test

91

OAD enable/disable toggle

92

TS CI path through with Reed Solomon off

95

Ether Check Ping (EG1H)

96

Digital debug output enable/disable

97

Digital 656 output enable/disable

98

Digital Auto Reset function enable/disable