Sony KDL-40NX720 / KDL-40NX723 / KDL-46NX720 / KDL-46NX723 / KDL-55NX720 / KDL-55NX723 / KDL-60NX720 / KDL-60NX723 Service Manual ▷ View online
Service Adjustment
4-5-3. Save changing data by Service Mode 2 (for 002 MODEL category)
4-6. White Balance Adjustment
KDL- 40, 46, 55, 60 NX720
RM-GD019
KDL- 40, 46, 55, 60 NX723
RM-GD019
3 T
h
i
d d
1. This is only required only when B Board is replaced.
2. Items in Digital service mode for 002 MODEL category.
000 SEG ・・・Select segment information
001 DEST・・・Select destination information
002 MODELNAME ・・・ Select Model Name
003 SERIAL ・・・Can be set Only Once for the new board
To access to White Balance Service mode, choose VPC Service Mode.
a. Press key
1 or 4 on remote commander to select WB adjustment menu.
006 WB category will be seen on the menu.
b. Change data by pressing
3 or 6. Each range of these items is 0~255.
c. Press
mute + 0 on remote commander to save the data.
SERVICE comment is changed to WRITE, indicating writing process.
d Af
hil
WRITE
SERVICE hi h
3. To change category, item and data :
a. Press key
2 or 5 on remote commander to select (up or down) category.
b. Press key
1 or 4 on remote commander to select (up or down) Item.
c. Press key
3 or 6 on remote commander to change (up or down) data.
Remote commander key :
1, 2, 3 is for increment
Remote commander key :
4, 5, 6 is for decrement
4 Press mute + 0 on remote commander It shows red WRITE as the indication
d. After a while,
WRITE comment returns to SERVICE, which means
writing process is done. (takes about a couple of seconds)
4. Press mute + 0 on remote commander . It shows red WRITE as the indication
that writing is in process.
5. After a while, red WRITE dissappers. Green Done will Display for a while,
which means writing process is done.
6. For the item SEG, DEST MODELNAME, after changing each item, service
save(mute+0) is needed.
For the item SERIAL after inputting the serial number press key 12 or Enter the
VPC
SERVICE
006
WB
000
R_DRV
128
VPC
SERVICE
006
WB
003
R_BKG
128
For the item SERIAL, after inputting the serial number, press key 12 or Enter, the
serial data will be saved.
7. Please save the item SEG, DEST, MODELNAME sequentially. (①SEG→
②DEST→③MODELNAME)
8. When Saving the item "SEG", sometimes instead of "Writing", word "Pending"
will appear. In this case, skip the "SEG", save the "DEST" and "MODELNAME" is
OK..
VPC
SERVICE
006
WB
001
G_DRV
128
VPC
SERVICE
006
WB
VPC
SERVICE
006
WB
004
G_BKG 128
VPC
SERVICE
006
WB
a
b
VPC Service menu sample
006
WB
002
B_DRV
128
006
WB
005
B_BKG
128
c
a
b
c
DIGITAL
SERVICE
002 MODEL
000 SEG
I-1
W it
DIGITAL Service menu
Remote Commander
– 36 –
Write
Remote Commander
Service Adjustment
KDL- 40, 46, 55, 60 NX720
RM-GD019
KDL- 40, 46, 55, 60 NX723
RM-GD019
In VPC service mode:
a. Select 000 DATA_COPY category by pressing key
2 or 5 on remote
commander.
b. Change data from
0 to 1 by pressing key 3 or 6 on remote commander.
c Wait until data is changed from
1 to 3
4-7. Restore WB / Gamma adj-data to B board.
4-8. Change the emitter output level (Applicable only for TD model).
1. Purpose to reduce the emitter LED output power strength.
2. Select VPC service mode and then press:
2. Select VPC service mode and then press:
a. Select 005 TD category by pressing key
2 or 5 on remote commander.
b. Select 000 EMIT_STR item by pressing key
1 or 4 on remote commander.
c. Change data from
0 to 1 by pressing key 3 or 6 on remote commander.
c. Wait until data is changed from
1 to 3.
d. When data is changed from
1 to 3, restoring process is finished.
e. In case data is changed from
1 to 2, keep default setting.
(No more process is needed.)
g
y p
g
y
0: Strong (Default)
1: Weak
d. Save by pressing
Mute & 0 or 10 & Reboot.
VPC SERVICE
000 DATA_COPY
000 BU_TRANS 3
VPC SERVICE
000 DATA_COPY
000 BU_TRANS 1
DO NOT POWER OFF
b
a
VPC SERVICE
005 TD
000 EMIT_STR 1
End restore process menu
DATA TRANSFER SUCCESS
Restore process menu sample
DO NOT POWER OFF
DO NOT TOUCH ANY KEY NOW
a
b
b
c
Sub Service menu
sample
Remote Commander
d
Notes:
1. This restoration should be applied after USB-DL being assembled when
B Board is replaced.
2. This process only applicable for 120Hz / 240Hz models only.
Remote Commander
– 37 –
Service Adjustment
KDL- 40, 46, 55, 60 NX720
RM-GD019
KDL- 40, 46, 55, 60 NX723
RM-GD019
To access VCOM Step 1, please select Digital Service Mode first
a. Select
003 DIG_SRV_MODE category by pressing key 2 or 5 on remote
commander.
4-9. Viewing VCOM Test Pattern
4-9-1. Step 1 (Step 1- 4 Not applicable for 3a-1)
4-9-1. Step 1 (Step 1- 4 Not applicable for 3a-1)
To access VCOM Step 3, please select VPC Service Mode.
a. Select 002 VCOM category by pressing key
2 or 5 on remote commander.
b. Select 001 ADJUST item by pressing key
1 or 4 on remote commander.
c. Change data by pressing key
3 or 6 on remote commander.
d Finish the adjustment when the picture seems OK
4-9-3. Step 3
b. Press key
0 on remote commander to go to TEST PATTERN Mode.
c. Press key
Enter or 1 or 2 on remote commmander to go into Video TEST
PATTERN.
d. Press key
7 or 8 on remote commander to select the test pattern
e. Press key
Enter or Select on remote commander twice to show the VCOM
PQP
SERVICE
002
VCOM
001 ADJUST 0
d. Finish the adjustment when the picture seems OK.
DIGITAL (DIG_SRV_MODE) SERVICE
TEST PATTERN
--> 1 Video
*1 White
2 Ramp
TEST PATTERN.
To access VCOM , Step 4, Please select Digital Service Mode
a. Select 007 VCOM category by pressing key
3 or 6 on remote commander.
b. Change data from 1 to 0 by pressing key 3 or 6 on remote commander.
c. Confirm the final result of the VCOM adjustment .
c. Confirm the final result of the VCOM adjustment .
4-9-4. Step 4
VCOM Test Pattern Step 3 menu sample
2 Ramp
3 R Raster
4 G Raster
5 B Raster
6 Color Bar
7 VCOM Pattern1
8 VCOM Pattern2
9 Off
Pl
i
t
hit l
l
DIGITAL SERVICE
010 VCOM
000 SRV_OSD_EN 1
c Co
t e a esu t o t e CO adjust e t
d. If OK, Finish the VCOM adjustment. If NG, pressing 6 to show the OSD
again and go back to VCOM adjustment STEP3
Please input a white level.
(00-10)
_ _
VCOM Test Pattern Step 1 menu sample
4-9-2. Step 2
VCOM Test Pattern Step 4 menu sample
1. a. In “VPC” service mode Select “002 VCOM” category by pressing “2 / 5” on remote.
category by pressing “2 / 5” on remote.
bb. . Select “000 ENABLE” item by pressing “1 / 4” on remote...
FOR 3a-1
PQP
SERVICE
a. Select
002 VCOM category by pressing key 2 or 5 on remote commander.
b. Select
000 ENABLE item by pressing key 1 or 4 on remote commander.
c. Change ENABLE from 0 to 1 to enable VCOM adjustment.
To access VCOM Step 2, please select VPCService Mode first
VPC
SERVICE
002
VCOM
000 ENAB
LE 0
cc. Change ENABLE from “0” to “1” to enable VCOM adjustment.
. Change ENABLE from “0” to “1” to enable VCOM adjustment.
–38–
002
VCOM
000 ENABLE 0
VCOM Test Pattern Step 2 menu sample
VCOM Test Pattern
Service Adjustment
KDL- 40, 46, 55, 60 NX720
RM-GD019
KDL- 40, 46, 55, 60 NX723
RM-GD019
FOR 3a 1
In detailed REC setting screen
a. Press “1” to select “Key Copy” item
bb. . Press “Enter” or “12” twice to execute the command.
c. If OK, show the message “Key Copy OK”
d If NG
h
th
“K C
NG (
)”
2. a. In “VPC” service mode select “002 VCOM” category by pressing “2 / 5” on remote.
b. Select “001 ADJUST” item by pressing “1 / 4” on remote..
c. Change data by pressing “3 / 6” on remote controller.
d. Finish the adjustment when the picture seems OK.
Attention:
・
・
Every time the data changed by pressing “3 / 6” Key the VCOM pattern will
FOR 3a-1
4-10-2. Step 2
DIGITAL (REC_SETTING)
SERVICE
REC_SETTING
* 1 Key Copy
2 HDD Re-Register
d. If NG, show the message “Key Copy NG (= xx )”
・
Every time the data changed by pressing 3 / 6 Key, the VCOM pattern will
display for 5s and in the mean time OSD will disappear, After the 5s period, VCOM
pattern will disappear and OSD will display again. The 5s time can be adjust by data
change.
・
・
If pressing the “3/6” key again during the 5s period, the VCOM pattern
display time will be extended to another 5s.
DIGITAL (REC_SETTIN SERVICE
REC_SETTING
* 1 Key Copy
2 HDD Re-Register
2 HDD Re Register
Key Copy OK
VPC
SERVICE
002
VCOM
001 ADJUST 64
VCOM Test Pattern
2 HDD Re Register
Key Copy NG (= xx )
REC Setting screen
4-10-3 Step 3
4-10. REC Setting
4-10-1. Step 1
IN “Digital” service mode
4-10-1. Step 1
IN “Digital” service mode
a. Select “003 DIG SRV MODE” category by pressing “2 / 5” on remote.
In detailed REC setting screen
a. Press “2” to select “HDD Re-Register” Item.
bb. . Press “Enter” or “12” twice to execute the command.
c. If OK, xx= x+1
d. If NG, xx=x
4-10-3 Step 3
DIGITAL (REC_SETTING) SERVICE
REC_SETTING
_
_
g y y p
g
b. Select “006 REC_SETTING ” item by pressing “1 / 4” on remote..
c. Press “0” or “10” to go to detailed REC Setting screen.
DIGITAL (REC_SETTING)
SERVICE
REC_SETTING
1 Key Copy
* 2 HDD Re-Register
(x) HDDs OK ( xx )
* 1 Key Copy
2 HDD Re-Register
REC Setting screen
REC Setting screen
–39–
Click on the first or last page to see other KDL-40NX720 / KDL-40NX723 / KDL-46NX720 / KDL-46NX723 / KDL-55NX720 / KDL-55NX723 / KDL-60NX720 / KDL-60NX723 service manuals if exist.