Sony KDL-32V2500 / KDL-40V2500 / KDL-46V2500 Service Manual ▷ View online
– 13 –
WAX2T
RM-ED008
Set-up menu
You can select the options listed below on the Set-up
menu. To select options in “Settings”, see “Navigating
through menus” (page
20).
Auto Start-up
Starts the “first time operation menu” to select the language and country/region, and
tune in all available digital and analogue channels. Usually, you do not need to do
this operation because the language and country/region will have been selected and
channels already tuned when the TV was first installed (page
5, 6). However, this
option allows you to repeat th
e process (e.g., to retune the TV after moving house,
or to search for new channels that
have been launched by broadcasters).
Language
Selects the language in which the menus are displayed.
AV Preset
Assigns a name to any equipment connected to the side and rear sockets. The name
will be displayed briefly on
the screen when the equipment is selected. You can skip
an input source that is not connected to any equipment.
1
Press
F
/
f
to select the desired input source
, then press
.
2
Press
F
/
f
to select the desired option belo
w
, then press
.
Equipment labels: Uses one of the preset labels to assign a name to connected
equipment.
“Edit”: Creates your own label. Follow steps 2 to 4 of “Programme Labels”
(page
29).
“Skip”: Skips an input source that is not connected to an
y equipment when you press
to select the input source.
Auto S Video
Selects the input signal from S video sockets
6 when
/
6 sock
ets are both
connected.
Timer Settings
Sets the timer to turn on/off the TV.
Sleep Timer
Sets a period of time after which the TV
automatically switches itself into standby
mode.
When the Sleep Timer is activated, the
(T
imer) indicator on the TV (front) lights
up in orange.
Tips
•
If you switch off the TV and switch it on
again, “Sleep Timer” is reset to “Off”.
•
“TV will soon turn off by sleep timer.” appears on the screen one minute before the TV
switches to standby mode.
PC Settings menu
You can select the options listed below on the PC
Settings menu. To select options in “Settings”, see
“Navigating through menus” (page
2
0).
Screen Format
Selects a screen mode for displaying input from your PC.
“Normal”: Displays the pict
u
re in its original size.
“Full1”: Enlarges the picture to fill the display area, keeping its original horizontal-
to-vertical aspect ratio.
“Full2”: Enlarges the picture to fill the display area.
Reset
Resets the PC settings except “Screen Format” and “Power Management” to the
factory settings.
Auto Adjustment
Automatically adjusts the display position and phase of the picture when the TV
receives an input signal from the connected PC.
Tip
Auto Adjustment may not work well with certain
input signals. In such cases, manually adjust
“Phase”, “Pitch”, “Horizontal Shift” and “Vertical Shift”.
Phase
Adjusts the phase when the screen flickers.
Pitch
Adjusts the pitch when the picture has unwanted vertical stripes.
Horizontal Shift
Adjusts the horizontal position of the picture for each screen format.
Vertical Shift
Adjusts the vertical position of the picture for each screen format.
Power Management
Switches the TV to standby mode if no
signal is received for 30 seconds.
– 14 –
WAX2T
RM-ED008
Analogue Set-up menu (Analogue mode only)
You can change/set the analogue settings using the
Analogue Set-up menu. To select options in
“Settings”, see “Navigating through menus”
(page
20).
1 Digit Direct
When “1 Digit Direct” is set to “On”, you can select an analogue channel using one
preset number button (0 - 9) on the remote.
Note
When “1 Digit Direct” is set to “On”, you cannot select channel numbe
rs 10 and above entering
two digits using the remote.
Auto Tuning
Tunes in all the available analogue channels.
Usually you do not need to do this operatio
n because the channels are already tuned
when the TV was first installed (page
5, 6). However, this option allows you to
repeat the process (e.g., to retune the TV after moving house, or to search for new
channels that have been launched by broadcasters).
Programme Sorting
Changes the order in which the analogue channels are stored on the TV.
1
Press
F
/
f
to select the channel y
o
u w
a
nt to mo
v
e
to a ne
w position,
then press
.
2
Press
F
/
f
to select the ne
w position
fo
r y
our channel, then press
.
Programme Labels
Assigns a channel name of your choice up to five letters or numbers. The name will
be displayed briefly on the screen when the channel is selected. (Names for channels
are usually taken automatically fro
m Analogue Text (if available).)
1
Press
F
/
f
to select the channel y
o
u w
a
nt to name
, then press
.
2
Press
F
/
f
to select the desired letter or n
u
mber (“_” f
o
r a b
lank space),
then press
g
.
If you input a wrong character
Press
G
/g
to select the wrong character. Then, press
F
/f
to select the correct
character.
To delete all the characters
Select “Reset”, then press
.
3
Repeat the procedure in step 2 until the name is complete
.
4
Select “OK”, then press
.
Digital Set-up menu
You can change/set the digital settings using the
Digital Set-up menu. Select “Digital Set-up” and press
to display the following menus. To select options
in “Settings”, see “Navigating through menus”
(page
20).
Digital Tuning
Displays the “Digital Tuning” menu.
Digital Auto Tuning
Tunes in all the available digital channels.
Usually you do not need to do this operatio
n because the channels are already tuned
when the TV was first installed (page
6). However, this option allows you to repeat
the process (e.g., to retune the TV after moving house, or to search for new channels
that have been launched by broadcasters).
Programme List Edit
Removes any unwanted digital channels stor
ed on the TV, and changes the order of
the digital channels stored on the TV.
1
Press
F
/
f
to select the channel y
o
u w
a
nt to remo
v
e
or mo
v
e
to a ne
w
position.
If you know the programme number (frequency)
Press the number buttons to enter the three-digit programme number of the broadcast
you want.
2
Remo
v
e
or change the order of the digital channels as f
o
llo
ws:
To remove the digital channel
Press
. A message that confirms whether the selected digital channel is to be
deleted appears. Press
G
to select “Yes”, then press
.
To change the order of
the digital channels
Press
g
, then press
F
/
f
to select the new position for the channel and press
G
.
Repeat the procedure in steps 1 and 2 to move other channels if required.
3
Press RETURN.
Digital Manual Tuning
Tunes the digital channels manually.
1
Press the n
u
mber b
u
tton to select the channel n
u
mber y
ou w
ant to
man
ually tune
, then press
F
/
f
to tune the channel.
2
When the a
v
ailab
le channels are f
o
und, press
F
/
f
to select the channel
y
o
u w
a
nt to store
, then press
.
3
Press
F
/
f
to select the prog
ra
mme n
u
mber where y
o
u w
a
nt to store the
ne
w channel, then press
.
Repeat the procedure above to tune other channels manually.
– 15 –
WAX2T
RM-ED008
Connecting optional equipment
Using Optional Equipment
You can connect a wide range of optional equipment to your TV. Connecting cables are not supplied.
Connecting to the TV (side)
Headphones
S VHS/Hi8/DVC
camcorder
T
o
connect
Do this
Conditional Access
Module (CAM)
A
T
o
use P
ay Per V
ie
w
services.
F
o
r details, refer to the instruction
manual supplied with your CAM.
T
o
use the CAM, remo
v
e the
rubber co
v
er from the CAM slot.
Switch of
f the TV when inserting
your CAM into the CAM slot.
When you do not use the CAM, we
recommend that you replace the
co
v
er on the CAM slot.
Note
CAM is not supported in all
countries. Please check with your
authorized dealer.
S VHS/Hi8/D
V
C
camcorder
B
Connect to the S video sock
et
6 or the video sock
et
6,
and the audio sock
ets
6. T
o
av
oid picture noise, do not connect
the camcorder to the video sock
et
6 and the S video sock
et
6 at the same time. If you
connect mono equipment, connect
to the L sock
et
6.
Headphones
C
Connect to the
i
sock
et to listen to
sound from the TV on headphones.
Continued
Connecting to the TV (rear)
DVD player
with component output
DVD player
Decoder
DVD recorder
VCR
Hi-Fi
Video game equipment
DVD player
Digital satellite receiver
PC
Decoder
T
o
connect
Do this
PC
D
Connect to the PC
/
sock
ets. It is recommended to use
a PC cable with ferrites.
Digital satellite
recei
v
er or D
V
D
player
E
, F
Connect to the HDMI IN 4 or 5
sock
et if the equipment has a
HDMI sock
et. The digital video
and audio signals are input from
the equipment. If the equipment
has a D
V
I sock
et, connect the D
V
I
sock
et to the HDMI IN 4 sock
et
through a D
V
I - HDMI adaptor
interf
ace (not supplied), and
connect the equipment’
s audio out
sock
ets to the audio in HDMI IN 4
sock
ets.
Notes
•
T
he HDMI sockets only support
the following video inputs: 480i,
480p, 576i, 576p, 720p, 1080i . To
connect a PC, please use the PC
socket.
•
B
e sure to use only an HDMI cable
that bears the HDMI logo.
D
V
D player with
component output
G
Connect to the component sock
ets
and the audio sock
ets
/
3
.
V
ideo game
equipment, D
V
D
player or decoder
H
Connect to the scart sock
et
/
1. When you connect the
decoder
, the scrambled signal from
the TV tuner is output to the
decoder
, then the unscrambled
signal is output from the decoder
.
D
V
D recorder or
VCR that supports
SmartLink
I
Connect to the scart sock
et
/
2. SmartLink is a direct link
between the TV and a VCR/D
V
D
recorder
.
Hi-Fi audio
equipment
J
Connect to the audio output
sock
ets
to listen to the sound
from the TV on Hi-Fi audio
equipment.
– 16 –
WAX2T
RM-ED008
Specifications
Display Unit
Power Requirements:
220–240 V AC, 50 Hz
Screen Size:
KDL-46V2500:
46 inches (Approx. 116.9 cm measured diagonally)
KDL-40V2500:
40 inches (Approx. 101.6 cm measured diagonally)
KDL-32V2500:
32 inches (Approx. 80.1 cm measured diagonally)
Display Resolution:
1,366 dots (horizontal) × 768 lines (vertical)
Power Consumption:
KDL-46V2500: 220 W
KDL-40V2500: 180 W
KDL-32V2500: 145 W
Standby Power Consumption:
0.3 W
Dimensions (w × h × d):
KDL-46V2500:
Approx. 1,126 × 805 × 334 mm (with stand)
Approx. 1,126 × 755 × 116 mm (without stand)
KDL-40V2500:
Approx. 988 × 716 × 265 mm (with stand)
Approx. 988 × 664 × 103 mm (without stand)
KDL-32V2500:
Approx. 792 × 593 × 219 mm (with stand)
Approx. 792 × 546 × 99 mm (without stand)
Mass:
KDL-46V2500:
Approx. 34 kg (with stand)
Approx. 28 kg (without stand)
KDL-40V2500:
Approx. 26 kg (with stand)
Approx. 21 kg (without stand)
KDL-32V2500:
Approx. 17 kg (with stand)
Approx. 15 kg (without stand)
Panel System
LCD (Liquid Crystal Display) Panel
TV System
Analogue:
Depending on your country/region selection:
B/G/H, D/K, L, I
Digital:
DVB-T
Colour/Video System
Analogue:
PAL, SECAM
NTSC 3.58, 4.43 (only Video In)
Digital:
MPEG-2 MP@ML
Aerial
75 ohm external terminal for VHF/UHF
Channel Coverage
Analogue:
VHF:
E2–E12
UHF:
E
21–E69
CATV:
S1–S20
HYPER:
S21–S41
D/K:
R1–R12, R21–R69
L:
F2–F10, B–Q, F21–F69
I:
UHF B21–B69
Digital:
VHF/UHF
Terminals
/1
21-pin Scart connector (CENELEC standard) including
audio/video input, RGB input, and TV audio/video
output.
/
2
(SmartLink)
21-pin Scart connector (CENELEC standard) including
audio/video input, RGB input, selectable audio/video
output, and SmartLink interface.
3
Supported formats: 1080i, 720p, 576p, 576i, 480p, 480i
Y: 1 Vp-p, 75 ohms, 0.3V negative sync
P
B
/C
B
: 0.7 Vp-p, 75 ohms
P
R
/C
R
: 0.7 Vp-p, 75 ohms
3
Audio input (phono jacks)
500 mVrms
Impedance: 47 kilo ohms
HDMI IN 4, 5
Video:
1080i, 720p, 576p, 576i, 480p, 480i
Audio:
Two channel linear PCM
32, 44.1 and 48 kHz, 16, 20 and 24 bits
Analogue audio (phono jacks):
500 mVrms, Impedance 47 kilohms
(HDMI IN 4 only)
6
S
video input (4-pin mini DIN)
6
V
ideo input (phono jack)
6
A
udio input (phono jacks)
Audio output (Left/Right) (phono jacks)
PC
PC Input (15 Dsub) (see page
37)
G: 0.7 Vp-p, 75 ohms, non Sync on Green
B: 0.7 Vp-p, 75 ohms, non Sync on Green
R: 0.7 Vp-p, 75 ohms, non Sync on Green
HD: 1-5 Vp-p
VD: 1-5 Vp-p
PC audio input (minijack)
i
Headphones jack
CAM (Conditional Access Module) slot
Additional Information
Sound Output
10 W + 10 W
Supplied Accessories
Refer to “1: Checking the accessories” on page
4.
Optional Accessories
•
W
all-Mount Bracket
SU-WL51 (for KDL-46V2500/KDL-40V2500)
SU-WL31 (for KDL-32V2500)
Design and specifications are subject to change
without notice.
PC Input Signal Reference Chart
•
T
his TV’s PC input does not support Sync on Green or Composite Sync.
•
T
his TV’s PC input does not
support interlaced signals.
•
F
or the best picture quality, it is recommended to use the si
gnals (boldfaced) in the above chart with a 60 Hz vertical freque
ncy
from a personal computer. In plug and play, signals with a 60 Hz vertical frequency will be selected automatically.
Signals
H
orizontal (Pix
el)
V
er
tical (Line)
Horizontal
frequenc
y
(kHz)
Ve
rt
ic
a
l
frequenc
y (Hz)
Standar
d
VG
A
640
480
31.5
6
0
V
GA
640
480
37.5
7
5
V
ESA
720
400
31.5
7
0
V
GA-T
SV
GA
800
600
37.9
60
VESA Guidelines
800
600
46.9
7
5
V
ESA
XGA
1024
768
48.4
6
0
V
ESA Guidelines
1024
768
56.5
7
0
V
ESA
1024
768
60
75
VESA
WXGA
1280
768
47.4
6
0
V
ESA
1280
768
47.8
6
0
V
ESA
1360
768
47.7
6
0
V
ESA
Click on the first or last page to see other KDL-32V2500 / KDL-40V2500 / KDL-46V2500 service manuals if exist.