DOWNLOAD Sony KDL-32NX500 / KDL-40NX500 Service Manual ↓ Size: 2 MB | Pages: 23 in PDF or view online for FREE

 

The following menu appears on the screen when you enter

 

the ‘OSD Service Menu’ (See Pic.4). This menu allows

 

viewing and adjustment of the AGC and viewing of the 

 

Sound Status.

 

The following menu appears on the screen when you enter

 

the ‘Country Selection’ menu (See Pic.5). Using this menu

 

the destination country of the TV can be set.

 

Selection of ‘Factory Reset’ (See Pic.6) allows the TV to be

 

reset to factory shipping condition. This will restore all

 

settings to those which were contained in the TV on first

 

shipment.

The TT modes described below are available by selecting the two 
relevant digits. You can exit the ‘TT Mode’ by entering 00, by
pressing the ‘Analog’ or the ‘Digital’ button, by switching  the TV 
set into stand-by mode, or by powering the TV set off.

Note :


To place the Remote Commander in ‘TT Mode’ press the

 

following buttons together for approximately five seconds.



To use the Remote Commander in ‘TT Mode’ press the

 

‘Rewind’ button on the Remote Commander twice.

 

TT will then appear in the bottom right hand corner of the TV.

i+

5

+

(ON SCREEN (DIGIT 5) (VOLUME +) (TV)
DISPLAY)



To take the Remote Commander out of ‘TT Mode’ press the

 

same buttons together for approximately five seconds.

Rewind Button

'TT' mode off

Set volume to 35%

Set volume to 50%

Set volume to 65%

Set volume to 80%

Ageing mode on

Shipping Condition

WB Levels Check

Panel_id A

Panel_id B

Speaker_id A

Speaker_id B

Factory toggle mode (ON/OFF)

CBA mode toggle (ON/OFF)

ECS mode toggle (ON/OFF)

Set DVB-T channel table

Set DVB-C channel table

Full HD HDMI EDID Write

WXGA HDMI EDID Write

Re-initialise NVM

Select Dual Sound "A"

Select Dual Sound "B"

Select Dual Sound "Mono"

Select Dual Sound "Stereo"

Set NVM as non-virgin

Set NVM as virgin

Clear authenticated CAM History

Clear service shunning cache

Enable/Disable DVB-C manual tuning

Set Centred Balance

Set Volume to Max

Set Volume to Min

Set Balance Full Left

Set Balance Full Right

Digital BER Display

TS CI Path Through

Front Panel Button Test

LED Test

TS CI Path Through With Reed Solomon Off

MAIN CHIP

PNX8543M2

Aerial/Cable

PC Audio

SCART1

SCART2

Line Out

Opt. Out

Component

USB

CICI

PC

BEN

HDMI1

HDMI2

HDMI3

HDMI4

HDMI
EQ/SW/EDID

TDA19997

HP Out

CV-Side

NVM

Key

IR

32,26,22

WXGA CCFL

46,40,37,32

FHD CCFL

DDR2

512Mb

DDR2

512Mb

Si-TU

SUT_AE102T

Demodulator

CXD2817R-T4
㧔DVB-T/C㧕

AUDIO
Buffer

CXA3813N

NAND FLASH

NAND01G
W3B2CN6F

AUDIO
D-Amp

TPA3110D2

Light 
Sensor

BH1690FVC

Control Button

HLR

PANEL

Power Supply

Gxx

LED

3a-2/5-0

5-2

H2LS

•

All capacitors are in µF unless otherwise noted.

•

pF : µµF 50WV or less are not indicated except for 
electrolytic types.

•

Indication of resistance, which does not have one for 
rating electrical power, is as follows.

Pitch : 5mm
Electrical power rating : 1/4W

•

Chip resistors are 1/10W

•

All resistors are in ohms.
k = 1000 ohms, M = 1000,000 ohms

•

: nonflammable resistor.

•

: fusible resistor.

•

: internal component.

•

: panel designation or adjustment for repair.

•

All variable and adjustable resistors have 
characteristic curve B, unless otherwise noted.

•

All voltages are in Volts.

•

Readings are taken with a 10Mohm digital mutimeter.

•

Readings are taken with a color bar input signal.

•

Voltage variations may be noted due to normal production
tolerences.

•

: B + bus.

•

: B - bus.

•

: RF signal path.

•

: earth - ground.

•

: earth - chassis.

: METAL FILM

: SOLID

: NON FLAMMABLE CARBON

: NON FLAMMABLE FUSIBLE

: NON FLAMMABLE METAL OXIDE

: NON FLAMMABLE CEMENT

: NON FLAMMABLE WIREWOUND

: ADJUSTMENT RESISTOR

: MICRO INDUCTOR

: TANTALUM

: STYROL

: POLYPROPYLENE

: MYLAR

: METALIZED POLYESTER

: METALIZED POLYPROPYLENE

: BIPOLAR

: HIGH TEMPERATURE

: HIGH RIPPLE

Les composants identifiés par une trame et
par une marque      sont d'une importance
critique pour la sécurité. Ne les remplacer
que par des pièces de numéro spécifié.
specified.

The components identified by shading
and marked      are critical for safety.
Replace only with the part numbers 
specified in the parts list.

CVM Board

A Board

S1 Board

VM

C

H

D1

A

J

A2

N

D

A1

D2

C

A