Sony KDL-32EX710 / KDL-40EX710 / KDL-40EX713 / KDL-46EX710 / KDL-46EX711 / KDL-46EX713 / KDL-55EX710 / KDL-55EX711 / KDL-55EX713 Service Manual ▷ View online
KDL-32EX710/40EX710/40EX713/46EX710/46EX711/46EX713/55EX710/55EX711/55EX713 4
ATTENTION!!
Ces instructions de service sont à l’usage du personnel de service qualifié seulement. Pour prévenir le risque de choc électrique, ne pas faire
l’entretien autre que celui contenu dans le Mode d’emploi à moins que vous soyez qualifié faire ainsi.
POUR TRANSPORTER LE TÉLÉVISEUR
• T ransportez le téléviseur av ec le nombre de personnes approprié ; un téléviseur de grande
taille doit être transporté par au moins deux personnes.
• L ors du transport du téléviseur , l’emplacement des mains est très important pour vo tre
sécurité, ainsi que pour év iter de causer des dommages.
ALERTE!!
Afin d’eviter tout risque d’electrocution provenant d’un chássis sous tension, un transformateur d’isolement doit etre utilisé lors de tout
dépannage. Le chássis de ce récepteur est directement raccordé à l’alimentation du secteur.
!
ATTENTION AUX COMPOSANTS RELATIFS A LA SECURITE!!
Les composants identifies par une trame et par une marque
!
sur les schemas de principe, les vues explosees et les listes de pieces sont
d’une importance critique pour la securite du fonctionnement. Ne les remplacer que par des composants Sony dont le numero de piece est
indique dans le present manuel ou dans des supplements publies par Sony. Les reglages de circuit dont l’importance est critique pour la securite
du fonctionnement sont identifies dans le present manuel. Suivre ces procedures lors de chaque remplacement de composants critiques, ou
lorsqu’un mauvais fonctionnement suspecte.
WARNING AND CAUTIONS
KDL-32EX710/40EX710/40EX713/46EX710/46EX711/46EX713/55EX710/55EX711/55EX713 5
USE CAUTION WHEN HANDLING THE LCD PANEL
When repairing the LCD panel, be sure you are grounded by using a wrist band.
When installing the LCD panel on a wall, the LCD panel must be secured using the 4 mounting holes on the rear cover.
When installing the LCD panel on a wall, the LCD panel must be secured using the 4 mounting holes on the rear cover.
1) Do not press on the panel or frame edge to avoid the risk of electric shock.
2) Do not scratch or press on the panel with any sharp objects.
3) Do not leave the module in high temperatures or in areas of high humidity for an extended period of time.
4) Do not expose the LCD panel to direct sunlight.
5) Avoid contact with water. It may cause a short circuit within the module.
6) Disconnect the AC power when replacing the inverter circuit.
(High voltage occurs at the inverter circuit at 650Vrms.)
7) Always clean the LCD panel with a soft cloth material.
8) Use care when handling the wires or connectors of the inverter circuit. Damaging the wires may cause a short.
9) Protect the panel from ESD to avoid damaging the electronic circuit (C-MOS).
10) During the repair,
DO NOT leave the Power On for more than 1 hour while the TV is face down on a cloth
.
SAFETY-RELATED WARNING
KDL-32EX710/40EX710/40EX713/46EX710/46EX711/46EX713/55EX710/55EX711/55EX713 6
After correcting the original service problem, perform the following safety checks before releasing the set to the customer:
1. Check the area of your repair for unsoldered or poorly soldered connections. Check the entire board surface for solder
splashes and bridges.
2. Check the interboard wiring to ensure that no wires are “pinched” or touching high-wattage resistors.
3. Check that all control knobs, shields, covers, ground straps, and mounting hardware have been replaced. Be absolutely
certain that you have replaced all the insulators.
4. Look for unauthorized replacement parts, particularly transistors, that were installed during a previous repair. Point them out
to the customer and recommend their replacement.
5. Look for parts which, though functioning, show obvious signs of deterioration. Point them out to the customer and
recommend their replacement.
6. Check the line cords for cracks and abrasion. Recommend the replacement of any such line cord to the customer.
7. Check the antenna terminals, metal trim, “metallized” knobs, screws, and all other exposed metal parts for AC leakage.
Check leakage as described below.
SAFETY CHECK-OUT
KDL-32EX710/40EX710/40EX713/46EX710/46EX711/46EX713/55EX710/55EX711/55EX713 7
SAFETY CHECK-OUT
LEAKAGE TEST
The AC leakage from any exposed metal part to earth ground and from all
exposed metal parts to any exposed metal part having a return to chassis, must
not exceed 0.5 mA(500 microamperes). Leakage current can be measured by any
one of three methods.
1. A commercial leakage tester, such as the Simpson 229 or RCA
WT-540A. Follow the manufacturers’ instructions to use these
instructions.
2. A battery-operated AC milliampmeter. The Data Precision 245 digital
multimeter is suitable for this job.
3. Measuring the voltage drop across a resistor by means of a VOM
or battery-operated AC voltmeter. The “limit” indication is 0.75 V, so
analog meters must have an accurate low voltage scale.
The Simpson’s 250 and Sanwa SH-63TRD are examples of
passive VOMs that are suitable. Nearly all battery-operated digital
multimeters that have a 2 VAC range are suitable (see Figure A).
HOW TO FIND A GOOD EARTH GROUND
The cover-plate retaining screw on most AC outlet boxes is at earth ground.Verify
the AC outlet box retaining screw ground by connecting a 60-to 100-watt trouble-
light (not a neon lamp) between the hot side of the receptacle and the retaining
screw. Try both slots, if necessary, to locate the hot side on the line; the lamp
should light at normal brilliance if the screw is at ground potential (see Figure B).
Trouble Light
AC Outlet Box
Figure B. Checking for Earth Ground
To Exposed Metal
Parts on Set
0.15 µF
Earth Ground
AC
Voltmeter
(0.75V)
Figure A. Using an AC voltmeter to check AC leakage.
Click on the first or last page to see other KDL-32EX710 / KDL-40EX710 / KDL-40EX713 / KDL-46EX710 / KDL-46EX711 / KDL-46EX713 / KDL-55EX710 / KDL-55EX711 / KDL-55EX713 service manuals if exist.