Sony KDL-26S3000 / KDL-32S3000 / KDL-40S3000 / KDL-46S3000 Service Manual ▷ View online
21
KDL-26S3000/32S3000/40S3000/46S3000
KDL-26S3000/32S3000/40S3000/46S3000
Inverter Cover
1
2
Plastic Strip
holding
Lamp Socket
holding
Lamp Socket
Plastic Strip
holding
Lamp Socket
holding
Lamp Socket
Inverter Board
DO NOT
REMOVE
BACKLIGHT
SCREWS
REMOVE
BACKLIGHT
SCREWS
SHIELD REMOVAL
INVERTER BOARD REMOVAL
WARNING
NEVER REMOVE THE
SCREWS SECURING THE
PLASTIC STRIP HOLDING
PLASTIC STRIP HOLDING
THE LAMP SOCKETS
DAMAGE TO THE
BACKLIGHT TUBES WILL
Only remove the screws securing the inverter
cover which may be metal or plastic. The
remaining plastic strip contains sockets for the
fluorescent backlights and should never be
loosened. The backlights will pop out of the
sockets and/or break the backlight requiring a
LCD panel replacement. The example shown
is a 32” model but applies to all models.
REMOVE SCREWS
SECURING
SHIELD
REMOVE
CONNECTOR AND
PULL BOARD TO
THE RIGHT
!
.
OCCUR!
BACKLIGHT
END VIEW
SOCKET
1-16. INVERTER BOARD REMOVAL
CAUTION:
Be sure to identify the inverter cover screws before proceeding. DO NOT remove the screws securing the plastic strip holding the lamp
sockets.
sockets.
1 Remove screws securing the inverter cover.
2 Remove screws securing the inverter board
2 Remove screws securing the inverter board
22
KDL-26S3000/32S3000/40S3000/46S3000
KDL-26S3000/32S3000/40S3000/46S3000
WIRE DRESSING
KDL-26S3000 ONLY
OVERALL VIEW
23
KDL-26S3000/32S3000/40S3000/46S3000
KDL-26S3000/32S3000/40S3000/46S3000
KDL-26S3000 ONLY
H3 BOARD HARNESS
1. Apply Sheet Core C to edge of Panel to
cover sharp edge of panel.
Use ribs on bezel (w/o screw boss) as a
guide to center tape.
2. Use 2nd UL Tape on H3-Bd harness to
align with edge of panel.
Apply Cushion D to edge of 2nd UL Tape as
shown.
Torque: 0.9
㧔N.m㧕
OPERATION PROCESS
TORQUE SPECIFICATION
Use UL Tape edge to align Himelon Tape.
Use ribs on bezel as reference
to center Sheet Core C when applying
to panel edge.
to center Sheet Core C when applying
to panel edge.
1
2
3
Use 2nd UL Tape wrapping (from H3-Bd)
as refrerence to position H3 cable.
NOTE edge of UL tape is aligned with
edge of panel.
as refrerence to position H3 cable.
NOTE edge of UL tape is aligned with
edge of panel.
24
KDL-26S3000/32S3000/40S3000/46S3000
KDL-26S3000/32S3000/40S3000/46S3000
KDL-26S3000 ONLY
1. Apply Sheet Core C as Shown on H3-Bd
Harness
2. Make sure wires do not cross over "bumps"
in the Panel. LVDS cable will be attached to
bumps (with 3x5mm screw-pinch points).
OPERATION PROCESS
Sheet Core C
Use Panel "bumps" as tape guide.
Use Panel "bumps" as tape guide.
NOTE ROUTING OF THE CABLES.
Cables CANNOT cross over top of
"bumps" on Panel.
Cables CANNOT cross over top of
"bumps" on Panel.
Sheet Core C installed (next to DTT lower shield)
1
2
2
H3 BOARD HARNESS (CONTINUED)
Click on the first or last page to see other KDL-26S3000 / KDL-32S3000 / KDL-40S3000 / KDL-46S3000 service manuals if exist.