Sony KDL-24W605A / KDL-32W503A / KDL-32W600A / KDL-32W603A / KDL-32W605A / KDL-32W650A / KDL-32W651A / KDL-32W653A / KDL-32W654A / KDL-32W655A / KDL-32W656A / KDL-40W905A / KDL-42W650A / KDL-42W651A / KDL-42W653A / KDL-42W654A / KDL-42W655A / KDL-42W656A / KDL Service Manual ▷ View online
RB1G
CHASSIS
Seg.
Model Name
Area
BT
Feature
Setting
Feature
Setting
HG/H2 KDL-** W900A, W904A, W905A,
W920A
All
0
TE
KDL-** W950A, W954A, W957A All
0
MD/MW KDL-** W808A
Hotel
2
KDL-** W805A
Argentina
2
KDL- ** W800A, W801A, W802A,
W804A, W805A, W807A,
W808A, W809A, W850A
W804A, W805A, W807A,
W808A, W809A, W850A
Others
0
LS
KDL-** W708A
Hotel
2
KDL- ** W700A, W704A, W705A,
W707A
W707A
Others
0
LW/L2 KDL-**W500A, W503A, W600A,
W603A, W605A, W607A,
W650A, W651A, W653A,
W654A, W655A, W656A,
W657A, W658A, W670A,
W674A, W685A
W650A, W651A, W653A,
W654A, W655A, W656A,
W657A, W658A, W670A,
W674A, W685A
All
2
CM
KDL-65S990A, 65S995A
All
0
MH
KDL-65W850A. 65W855A
All
0
9
Note : Black font : Procedure/ Step
Red font : Caution ( Additional Info)
Blue font: Additional Info.
Red font : Caution ( Additional Info)
Blue font: Additional Info.
6. Press “OPTIONS” on remote. In “VPC” service mode
(FOR TE, HG, CM, MH, H2)
(FOR TE, HG, CM, MH, H2)
a.Select “000 DATA_COPY” category by pressing “2 / 5” on remote.
b.Change data from “0” to “1” by pressing “3 / 6” on remote.
c.Wait until data is changed from 1 to 3.
d.When data is changed from 1 to 3, restoring process is finished.
e.In case data is changed from 1 to 2, keep default setting. (No more
process is needed.)
b.Change data from “0” to “1” by pressing “3 / 6” on remote.
c.Wait until data is changed from 1 to 3.
d.When data is changed from 1 to 3, restoring process is finished.
e.In case data is changed from 1 to 2, keep default setting. (No more
process is needed.)
Remote Commander
a
b
End restore process
VPC
SERVICE
000
DATA_COPY
000
BU_TRANS
3
DATA TRANSFER SUCCESS
Restore process
VPC
SERVICE
000
DATA_COPY
000
BU_TRANS
1
DO NOT POWER OFF
DO NOT TOUCH ANY KEY NOW
DO NOT TOUCH ANY KEY NOW
OPTIONS
CHASSIS
SERVICE
008
BT MODE
000
FEATURE 0
Press 2: increment
Press 5: decrement
Press 5: decrement
Press 1: increment
Press 4: decrement
Press 4: decrement
Press 3: increment
Press 6: decrement
Press 6: decrement
CHASSIS Service menu
7. Press “OPTIONS” on remote. In “CHASSIS” service mode .
a.Select “008 BT MODE” category by pressing “2 / 5” on remote.
b.Press “1 / 4” on remote to select (up / down) Item.
c.Press “3 / 6” on remote to change (up / down) data.
b.Press “1 / 4” on remote to select (up / down) Item.
c.Press “3 / 6” on remote to change (up / down) data.
SERVICE PROCEDURE
( BOARD)
( BOARD)
Reference Table
d. Press “Mute” on remote.
It shows green “SERVICE” changes to green “WRITE”.
e. Press “0” on remote. Green “WRITE” changes to red “WRITE”. It
indicate writing is processing.
f. After a while, red “WRITE” changes to green “SERVICE”. Writing process is
It shows green “SERVICE” changes to green “WRITE”.
e. Press “0” on remote. Green “WRITE” changes to red “WRITE”. It
indicate writing is processing.
f. After a while, red “WRITE” changes to green “SERVICE”. Writing process is
done at this point.
TV reboot is necessary for applying data change.
CHASSIS
WRITE
008
BT MODE
000
FEATURE 0
CHASSIS Service Menu
BT Feature summary
SEG
Model Name
HG
KDL-**W90*A
TE
KDL-**W95*A
CM
KDL-65S99*A
MH
KDL-65W85*A
H2
KDL-**W920A
RB1G
CHASSIS
10
Note : Black font : Procedure/ Step
Red font : Caution ( Additional Info)
Blue font: Additional Info.
Red font : Caution ( Additional Info)
Blue font: Additional Info.
DIGITAL
SERVICE
002 MODEL
005 VAR_TYPE STD
VIDEO: DYNAMIC AUDIO:DYNAMIC
PSAVE:STANDARD
MAIN:
SUB:
TUNER/----/----- -----/----/NTSCU
----x----/------ ----x----/------
-----/---
----x----/------ ----x----/------
-----/---
-----/---
DIGITAL Service
Menu
Menu
9. After completing all the service adjustment changes, verify that the correct
Model ID and Product ID displays in the Service menu.
Model ID and Product ID displays in the Service menu.
a.Press the OPTIONS key to go to the Digital Service menu. (There
are 3 Service menus “DIGITAL”
are 3 Service menus “DIGITAL”
“CHASSIS” “VPC”)
b.Verify the Software version, Model ID and Product ID are the
correct
correct
Remote Commander
OPTIONS
Model ID
Product ID
Software
Package
Version
Package
Version
DIGITAL SERVICE
001 OP
000 VERS ---
<MAIN> <EXT>
DM1.301W00AA WF:2.0.0.99
WF1.003W00AA WF:--------
DF1.001W00AA FD:0.068
YM1.010W00AA BT:
M4.922C
1.2.14.891
(DM1.301W00AA)
DD1.016W00AA
PK0.312W00AA
AM0.510WW
MID:04835511
PID:04020000
PNL:LTY320AB01
DQ3Y550LN0101
10. Switch off then on the AC supply.
Digital Service menu
SERVICE PROCEDURE
( BOARD)
( BOARD)
Please refer to Appendix pages to verify the Model ID and Product ID.
8. In “Digital” Service Mode
a. Select
“002 MODEL”
category by pressing “2” and “5” on remote.
b. Press “1” or “4” on remote to select 005 VAR_TYPE.
c. Change data by pressing “3” or “6” on remote.
d. After data is selected, press “Mute” then “0”.
e. When Smart Core Green and Amber LED blink alternately , insert USB
with software.
f. After a few minutes, Smart Core White LED will lit.
g. TV reboots itself and goes to standby mode.
h. Turn on TV by “Power” key on TV or “Power” button on remote.
i. Message of Software Update completion will appear.
j. Disconnect USB.
k. 001 DEST update is necessary if VAR_TYPE is changed from STD
(Refer to below reference table).
l. If VAR_TYPE is not changed, proceed to Task [9]
Variable Type
Description
Variation_01(Standard)
General purpose (except below)
Variation_02(AUS_NZ)
for PA(T and T2) model of Australia and New Zealand.
GALF, India or other PA regions are specified by "Variation_01 (Standard)"
This Variable Type AUS_NZ is applicable except for LW.
GALF, India or other PA regions are specified by "Variation_01 (Standard)"
This Variable Type AUS_NZ is applicable except for LW.
Variation_03(UC)
for U/C model.
Korea or Latin ATSC model are specified by "Variation_01 (Standard)"
This Variable Type UC is applicable except for LW.
Korea or Latin ATSC model are specified by "Variation_01 (Standard)"
This Variable Type UC is applicable except for LW.
Variation_04(CH_EEI)
for China model.
Variation_05(MK2)
for Japan L2 model.
Reference Table
RB1G
CHASSIS
Some user setting may have
changed during the update.
Please remove the USB device and
select ""OK to exit.
Status 1
Status 2
Remove
Remove
1) Replace a panel module (Refer to each segment Service Manual for
Board (Tcon, Driver/ Converter & Panel) details).
2) After AC Plug-in(AC On), wait for 20s then turn on TV by power key on
TV or Remote Commander.
Note : Important: 20s wait is necessary for
successful SW writing in Task [3].
b) When you turn on the TV after replacing Panel , there will be two
cases depend on the PANEL ID setting. Below are the example:
cases depend on the PANEL ID setting. Below are the example:
3)
Software update by USB memory. (refer to section 1.3 Preparing USB for
Upgrade)
i) Remove all signal connection.(antenna, external input, ether cable, etc)
ii) Insert the USB memory.
Upgrade)
i) Remove all signal connection.(antenna, external input, ether cable, etc)
ii) Insert the USB memory.
iii) If older software package version is used, smart core amber and
green LED will remain blinking. (Software can not update).
green LED will remain blinking. (Software can not update).
iv)If valid file found, below message will appear. TV will reboot in a
minute after the USB device is inserted, then the Red LED lights and the
Amber LED blinks
minute after the USB device is inserted, then the Red LED lights and the
Amber LED blinks
11
SERVICE PROCEDURE
( PANEL)
( PANEL)
SERVICE PROCEDURE (PANEL)
SECTION 3
i) Panel : No Picture- SMART CORE LED :
Amber & Green blinking
Amber & Green blinking
ii) Panel : Picture appear
SMART CORE LED : White Lit
SMART CORE LED : White Lit
4) TV on standby. Enter Service Mode. Press “i+ (info)”, “5”, “Volume +” then “TV
power” on remote.
Note : a) <Restriction>When TV power status is "Deep STBY Mode", you
cannot enter Service Mode due to not receive the above SIRCS command.
cannot enter Service Mode due to not receive the above SIRCS command.
b) <Operation method> (To enter this mode surely.)
After TV goes to STBY status by Remote commander, Please input the
sequence (four keys described above) by RC within 15 seconds (UC) or 1
minute (Other Destination).
sequence (four keys described above) by RC within 15 seconds (UC) or 1
minute (Other Destination).
3-1. Service Procedure for Panel Module replacement.
Note :
Black font : Procedure/ Step
Red font : Caution ( Additional Info).
Blue font: Additional Info.
Black font : Procedure/ Step
Red font : Caution ( Additional Info).
Blue font: Additional Info.
Preparing for software update.
During the system update, the TV
will automatically restart.
Please do not disconnect the power or
remove the USB device, until update
is completed.
The update may take up to 5 minutes.
Copying update file from USB.
Please wait...
v) Status 1: Please wait awhile, until the SMART CORE LED will change to white blinking
then TV goes to Standby (Software update complete). Turn on TV. OR
then TV goes to Standby (Software update complete). Turn on TV. OR
-
.
v) Status 2: After SW completes, TV will reboot itself and message will appear to
indicate SW update complete/
indicate SW update complete/
5. i) Select VPC (FOR TE, HG, CM, MH, H2)
a)
Press the “2/5” key on the remote commander to select 001 DATA_BACKUP.
b)
Press the “1/4” key on the remote commander to select 000 BU_FLASH.
c)
Press the “3/6” key on the remote commander to select from 0 to 1. Data
transfer will be done in few seconds.
transfer will be done in few seconds.
1 -> 3 : Data Backup OK case
1 -> 2 : Data Backup NG case
1 -> 2 : Data Backup NG case
Press 2: increment
Press 5: decrement
Press 5: decrement
Press 1: increment
Press 4: decrement
Press 4: decrement
Press 3: increment
Press 6: decrement
Press 6: decrement
VPC SERVICE
001 DATA_BACKUP
000 BU_FLASH 2
DATA TRANSFER NG
VPC SERVICE
001 DATA_BACKUP
000 BU_FLASH 3
DATA TRANSFER SUCCESS
NG
OK
VPC Service menu
SEG
Model Name
HG/H2
KDL-**W90*A, W920A
TE
KDL-**W95*A
CM
KDL-65S99*A
MH
KDL-65W85*A
VPC SERVICE
001 DATA_BACKUP
000 BU_FLASH 1
RB1G
CHASSIS
12
SERVICE PROCEDURE
( PANEL)
( PANEL)
6. After completing all the service adjustment changes, verify that the correct
Model ID and Product ID displays in the Service menu.
Model ID and Product ID displays in the Service menu.
a.Press the OPTIONS key to go to the Digital Service menu. (There
are 3 Service menus “DIGITAL”
are 3 Service menus “DIGITAL”
“CHASSIS” “VPC”)
b.Verify the Software version, Model ID and Product ID are the
correct
correct
Remote Commander
OPTIONS
Model ID
Product ID
Software
Package
Version
Package
Version
DIGITAL SERVICE
001 OP
000 VERS ---
<MAIN> <EXT>
DM1.301W00AA WF:2.0.0.99
WF1.003W00AA WF:--------
DF1.001W00AA FD:0.068
YM1.010W00AA BT:
M4.922C
1.2.14.891
(DM1.301W00AA)
DD1.016W00AA
PK0.312W00AA
AM0.510WW
MID:04835511
PID:04020000
PNL:LTY320AB01
DQ3Y550LN0101
Digital Service menu
7. Reset Panel Operation Time.
a. Go to TV standby condition by remote commander.
b. Press “i+ (info)”, “5”, “Volume-” then “TV power” on remote.
c. You can see Self Diagnosis Display.
a. Go to TV standby condition by remote commander.
b. Press “i+ (info)”, “5”, “Volume-” then “TV power” on remote.
c. You can see Self Diagnosis Display.
d. Reset Panel Operation Time . Press <7> + <0> on remote.
`
SELF CHECK
002 MAIN_POWE ------------ -----------00 Model Name : KDL-46W900A
003 AFE_I2C ------------ ------------ 00 Serial Number : 1514561
003 DC_ALERT------------ ------------ 00 Package Number : PKG1.301JPA
003 AUD_PROT------------ ------------ 00 Device ID : B0:00:00:E5:D1:B2
003 HDMI_EQ------------ ------------ 00 Wired MAC : 30:F9:ED:04:2C:17
003 TU_DEMOD------------ ------------ 00 Wireless MAC : N/A
003 AFE_SPI------------ ------------ 00 USB dongle : N/A
004 VLED ------------ ------------ -- 00
004 LD_ERR ------------ ------------ 00 <MAIN> <EXT>
005 TCON_ERR120823132523 ------------ 01 DM1.301JPA WF:2.0.0.99
005 P_ID_ERR------------ ------------ 00 WF1.003W00AA WF:0B
006 BACKLITE------------ ------------ 00 DF1.001W00AA FD:-.---
007 TEMP_ERR------------ ------------ 00 YM1.010W00AA BT:1.2.14.848
007 FAN_ERR------------ ------------ -00 M4.992C
008 VPC_WDT------------ ------------ -00 (DM1.301W00AA)
008 MEPS_WDT------------ ------------ 00 DD1.016W00AA
008 HOST_WDT------------ ------------ 00 PK1.016W00AA
008 STBY_WDT------------ ------------ 00 AM1.300JP
008 AFE_WDT------------ ------------ -00
010 EMIT_ERR------------ ------------ 00 MID:1C117081
PID:04020000
PNL:LC470EUF-FFP1
00081-00671-00088 00000000000000000570-00000000000000000132
Panel Operation
Time
Time
Diagnosis Display
8. The upgrade process is complete and unplug the AC cord.
30 分後
Please refer to Appendix pages to verify the Model ID and Product ID.
Click on the first or last page to see other KDL-24W605A / KDL-32W503A / KDL-32W600A / KDL-32W603A / KDL-32W605A / KDL-32W650A / KDL-32W651A / KDL-32W653A / KDL-32W654A / KDL-32W655A / KDL-32W656A / KDL-40W905A / KDL-42W650A / KDL-42W651A / KDL-42W653A / KDL-42W654A / KDL-42W655A / KDL-42W656A / KDL service manuals if exist.