Sony KD-49X8005C Service Manual ▷ View online
KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C
113
TROUBLE SHOOTING
3-2-2. NO POWER-U-Com Failure (1/2)
START
Check R9186 Voltage.
Is the voltage >3.0V?
Check OPWRSB
R9179 Voltage.
Is the voltage 0V?
Check DC_OFF_DET
IC9018
No problem
TV set stays in
STBY MHL charge mode.
No
Yes
No
Yes
Check P_ON_LNB
P-on ucom #pin15
Is the voltage >3.0V?
Change IC9017
No
yes
Check MAIN_VCC
R9175 Voltage.
Is the voltage >1.6V?
G-Board
No
Yes
Check P_ON_VBUS
P-on ucom #pin11
is >3.0V?
Change IC9017
No
Yes
Yes
Change IC9017
No
Check P_ON_#1
P-on ucom #pin13
is >3.0V?
Check PGOOD_1
R9173 Voltage.
Is the voltage >3.0V?
No POWER - DDCON/LDO
Check 1.0V DDCON (IC9008)
No
Check C9117 Voltage.
Is the voltage >3.0V?
Check +3.3V_STBY
R9144, CN9000 #26pin
No
Check POWER_ON
P-on ucom #pin19
Is the voltage >3.0V?
Try AC Off and On after few minutes.
If #pin19 keep Low, change IC9017.
If #pin19 goes High few seconds and downs to Low,
Check G board and harness.
No
Yes
Check STBY_MHL
R9176 Voltage.
Is the voltage >3.0V?
Yes
SOC
Muffin
problem
No
Yes
A
To the next page
KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C
114
TROUBLE SHOOTING
3-2-2. NO POWER-U-Com Failure (2/2)
A
Yes
Check P_ON_#2
P-on ucom #pin14
Is the voltage >3.0V?
Change IC9017
No
Yes
Check ORESETB
P-on ucom #pin12
Is the voltage >3.0V?
Change IC9017
No
Yes
Change IC9017
No
END
Ucom IC9017 is working OK
Yes
Check X_SYSTEM_RST
P-on ucom #pin16
Is the voltage >3.0V?
Change IC9017
No
Yes
If BL_MUTE (R9174) is 0V
Check BL_ON
P-on ucom #pin18
Is the voltage >3.0V?
Change IC9017
No
Yes
If PANEL_PWER_ON (R9172) is 0V
Check XRST
P-on ucom #pin17
Is the voltage >3.0V?
From previous page
KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C
115
TROUBLE SHOOTING
3-2-4. NO POWER: DDCONs check
START
Check Vdd
C9118
Is voltage >5V?
Change IC9018
Yes
No
END
Check Enable pin
voltage
Is voltage >2.5V?
No Power U-Com Failure
Change Fuse
No
No
START
Yes
Change DDCON IC
Check fuse
F9xxx
Is fuse OK?
Check Vcc voltage
C9xxx
Is voltage >12.0V?
Check POWER_ON P-on ucom #pin19
(Refer to No Power U-Com Failure)
No
Yes
Yes
3-2-3. NO POWER: DC_OFF_DET check
116
KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C
TROUBLE SHOOTING
3-2-5. NO POWER: DDCON check
Check Enable
IC9010 #pin1
Is voltage >2.5V?
Change IC9010
Change D9000
No
No
START
Yes
Change DDCON
IC9009
Check Vcc voltage
C9061
Is voltage >3V?
Yes
Check
D9000
Is diode ?
No
Yes
Check G board and harness
Change D9001
No
Check Vcc voltage
C9061
Is voltage >4V?
Yes
Check
D9001
Is diode ?
No
Yes
Check +5V_MAIN DDCON (IC9001)
Check IC9403 Vcc voltage
C9428
Is voltage >12V?
No
Yes
Click on the first or last page to see other KD-49X8005C service manuals if exist.