Sony VPL-HS51A / VPL-HS60 Service Manual ▷ View online
1-9
VPL-HS60/HS51A
7.
Remove the shield plate (BD) in the direction shown
by the arrow.
by the arrow.
8.
Remove the shield plate (BU) in the direction shown
by the arrow.
by the arrow.
9.
Remove the four hooks of the holder (BD), then
remove the holder (BU) and lamp power supply board.
remove the holder (BU) and lamp power supply board.
10. Disconnect the harness from the connector on the lamp
power supply board.
Installation
11. Install the lamp power supply board in the reverse
11. Install the lamp power supply board in the reverse
order of steps 5 to 10.
12. Assemble this unit in the reverse order of steps 1 to 4.
A
A
B
B
Shield plate (BD)
Shield plate (BU)
Hooks
Hook
Holder (BD)
Holder (BU)
Harness
Lamp power supply
board
board
1-4-7. F Board
Removal
1.
1.
Remove the cabinet. (Refer to Section 1-3.)
2.
Disconnect the five harnesses from the connector
(CN10 to CN14) on the F board.
(CN10 to CN14) on the F board.
3.
Remove the two screws, then remove the F board.
Installation
4.
4.
Install the F board in the reverse order of steps 2 and 3.
5.
Attach the cabinet.
BTP
3
3
x 12
CN13
CN12
CN11
CN14
CN10
F board (Side A)
F board
Harnesses
Harnesses
1-10
VPL-HS60/HS51A
1-4-8. HA Board/HB Board/L Board
Removal
1.
1.
Remove the cabinet. (Refer to Section 1-3.)
2.
Remove the C board.
(Refer to steps 3 to 7 of Section 1-4-1.)
(Refer to steps 3 to 7 of Section 1-4-1.)
3.
Remove the lamp assembly.
(Refer to steps 2 and 3 of Section 1-5-2.)
(Refer to steps 2 and 3 of Section 1-5-2.)
4.
Remove the optical block assembly.
(Refer to step 5 of Section 1-5-3.)
(Refer to step 5 of Section 1-5-3.)
5.
Remove the lamp house.
(Refer to step 5 of Section 1-4-6.)
(Refer to step 5 of Section 1-4-6.)
6.
Remove the duct lamp assembly.
7.
Remove the three screws, then remove the GA/GB unit.
8.
Remove the two screws, then remove the fan holder (G).
9.
Remove the HA board.
10. Remove the escutcheon (H) from the top panel
assembly.
11. Remove the four hooks, then remove the HB board.
12. Disconnect the harness from the connector (CN80) on
12. Disconnect the harness from the connector (CN80) on
the HB board.
13. Remove the button (P) from the HB board.
14. Remove the L board.
15. Disconnect the harness from the connector (CN001)
14. Remove the L board.
15. Disconnect the harness from the connector (CN001)
on the L board.
HA board
Button (P)
HB board
L board
Duct lamp assembly
CN80
CN001
Top panel assembly
Escutcheon (H)
Hooks
Harness
Harness
BTP
3
3
x 12
Fan holder (G)
BTP
3
3
x 12 (BLK)
GA/GB unit
Installation
16. Install the HA board, HB board and L board in the
16. Install the HA board, HB board and L board in the
reverse order of steps 6 to 15.
17. Assemble this unit in the reverse order of steps 1 to 5.
1-11
VPL-HS60/HS51A
1-4-9. Q Board (VPL-HS51A)
Removal
1.
1.
Remove the base assembly. (Refer to Section 1-3-1.)
2.
Remove the front panel (D) assembly.
(Refer to steps 2 to 4 of Removal (VPL-HS51A) in
Section 1-3-2.)
(Refer to steps 2 to 4 of Removal (VPL-HS51A) in
Section 1-3-2.)
3.
Remove the two screws, then remove the Q board.
4.
Disconnect the harness from the connector (CN5002)
on the Q board.
on the Q board.
Installation
5.
5.
Install the Q board in the reverse order of steps 3, 4.
6.
Assemble this unit in the reverse order of steps 1 and 2.
Shield plate
(ED)
(ED)
PSW
3
3
x 8
Shield plate (EU)
Q board
Harness
CN5002
DC fan
(for GA/GB unit)
(for GA/GB unit)
BTP
3
3
x 12
BTP
3
3
x 12
Fan holder (G)
1-5. Replacing the Main Parts
1-5-1. DC Fan (for GA/GB unit)
Removal
1.
1.
Remove the cabinet. (Refer to Section 1-3.)
2.
Remove the C board.
(Refer to steps 3 to 7 of Section 1-4-1.)
(Refer to steps 3 to 7 of Section 1-4-1.)
3.
Remove the lamp assembly.
(Refer to steps 2 and 3 of Section 1-5-2.)
(Refer to steps 2 and 3 of Section 1-5-2.)
4.
Remove the optical block assembly.
(Refer to step 5 of Section 1-5-3.)
(Refer to step 5 of Section 1-5-3.)
5.
Remove the lamp house.
(Refer to step 5 of Section 1-4-6.)
(Refer to step 5 of Section 1-4-6.)
6.
Remove the duct lamp assembly.
(Refer to step 6 of Section 1-4-8.)
(Refer to step 6 of Section 1-4-8.)
7.
Remove the two screws, then remove the fan holder (G).
8.
Remove the two screws, then remove the DC fan (for
GA/GB unit).
GA/GB unit).
Installation
9.
9.
Attach the DC fan (for GA/GB unit) in the reverse
order of steps 7 and 8.
order of steps 7 and 8.
10. Assemble this unit in the reverse order of steps 1 to 6.
1-12
VPL-HS60/HS51A
1-5-2. Lamp Assembly
Removal
1.
1.
Loosen the screw [A], then remove the lamp cover
assembly.
assembly.
2.
Loosen the three screws [B].
3.
Hold the lamp handle, then lift the lamp assembly
slowly.
slowly.
Installation
4.
4.
Attach the lamp assembly in the reverse order of steps
1 to 3.
n
When attaching the lamp assembly, be sure to securely
insert the connector [A] of the lamp assembly into the
connector [B] of the lamp house.
1 to 3.
n
When attaching the lamp assembly, be sure to securely
insert the connector [A] of the lamp assembly into the
connector [B] of the lamp house.
1-5-3. Optical Block Assembly
Removal
1.
1.
Remove the cabinet. (Refer to Section 1-3.)
2.
Remove the C board.
(Refer to steps 3 to 6 of Section 1-4-1.)
(Refer to steps 3 to 6 of Section 1-4-1.)
3.
Remove the lamp assembly.
(Refer to steps 2 and 3 of Section 1-5-2.)
(Refer to steps 2 and 3 of Section 1-5-2.)
4.
Remove the lamp power supply board.
(Refer to steps 4 to 10 of Section 1-4-6.)
(Refer to steps 4 to 10 of Section 1-4-6.)
5.
Remove the screw and two spacers, then remove the
optical block assembly.
optical block assembly.
Installation
6.
6.
Attach the optical block assembly in the reverse order
of step 5.
of step 5.
7.
Assemble this unit in the reverse order of steps 1 to 4.
Lamp cover assembly
Screw [A]
Screw [B]
Screw [B]
Screw [B]
Lamp handle
Lamp assembly
Connector
[A]
[A]
Connector [B] of
lamp house
lamp house
BTP
3
3
x 12
Optical block
assembly
assembly
Spacer
Click on the first or last page to see other VPL-HS51A / VPL-HS60 service manuals if exist.