DOWNLOAD Sony VPL-AW10 / VPL-AW15 Service Manual ↓ Size: 8.66 MB | Pages: 102 in PDF or view online for FREE

1-17

VPL-AW10/AW15

9 Two claws
     (+PSW M3 

x 8)

4 Screw
     (+PSW M3 

x 8)

!- F board

3 Two screws
     (+BVTP 3 

x 12)

!= Screw
     (+PSW 4 

x 8)

0 Open the clamp

Shield case (F),
F board cover (B), Sheet (F)

![ Two claws
     (+K M3 

x 8)

!] AC inlet

7 Shield cover (F)

8 F board cover (T)

5 Five dowels

2 Open the clamp

CN002

CN001

1 Tape

6 Claw

1-18

VPL-AW10/AW15

A Flat connector assembly (32P) x 3

B Flat connector assembly (24P)

F Connector assembly (4P)

C ZH connector assembly (8P)

G Connector assembly (7P)

H Connector assembly (8P)

D GH connector assembly (6P)

E GH connector assembly (9P)

I Connector assembly (9P)

J Connector assembly (13P)

CN400

CN600

CN10400

CN10600

CN1000

CN11000

CN11201

CN1201

CN1200

CN11200

CN701

CN702

CN703

CN10701

CN10702

CN10703

CN10705

CN705

CN1300

CN11300

CN900

CN1100

CN11100

CN10900

H board

Top Cover Assembly 

Shield 
cover (C)

FFC clamp 

x 3

Shield cover (G)

Q board

C board

C board section

1-19

VPL-AW10/AW15

J

I

E

G

C

A x 3

B

F

D

H

CN12

CN60

Q board

C board

X board

H board

CN400

CN600

CN10400

CN10600

CN1000

CN11000

CN11201

CN1201

CN1200

CN11200

CN701

CN702

CN703

CN10701

CN10702

CN10703

CN10705

CN1300

CN11300

CN900

CN1100

CN11100

CN10900

CN400

CN600

CN1000

CN1201

CN1200

CN701

CN702

CN703

CN1300

CN900

CN1100

CN705

CN705

A Flat connector assembly (32P) x 3
B Flat connector assembly (24P)
C ZH connector assembly (8P)
D GH connector assembly (6P)
E GH connector assembly (9P)
F Connector assembly (4P)
G Connector assembly (7P)
H Connector assembly (8P)
I Connector assembly (9P)
J Connector assembly (13P)

1-20

VPL-AW10/AW15

Boards requiring use of unleaded solder are printed with a
lead free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come
printed with the lead free mark due to their particular size.)

 : LEAD FREE MARK

m
. Be sure to use the unleaded solder for the printed circuit

board printed with the lead free mark.

. The unleaded solder melts at a temperature about 40 dC

higher than the ordinary solder, therefore, it is recom-
mended to use the soldering iron having a temperature
regulator.

. The ordinary soldering iron can be used but the iron tip

has to be applied to the solder joint for a slightly longer
time. The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful.

1.

Write the Look Up Table/3D gamma data contained in
the attached floppy disk.
See “1-6. Writing Look Up Table/3D gamma/DDC
data” for more about how to write data.

2.

Perform white balance adjustment. (See “2-5. White
Balance Adjustment on servicing”)

3.

Change the IRIS data to the values of the IRIS adjust-
ment data stored in the supplied floppy disk. For how
to change the data, refer to “1-5-3. IRIS Copy”.

1) When the C board is replaced

a)

Remove IC803 from the old C board and install it
to the new board.

b) Perform V COM adjustment according to section

2-3.

c)

Change the IRIS data to the values of the IRIS
adjustment data before replacement. (For the
method to change the IRIS data, refer to “1-5-3.
IRIS Copy”.)
When the adjustment data cannot be copied, adjust
IRIS. (Refer to “2-4. IRIS Adjustment”.)

d) Change the W/B data to the values of the W/B

adjustment data before replacement. (For the
method to change the W/B data, refer to “1-5-4.
W/B Copy”.)
When the adjustment data cannot be copied, adjust
W/B. (Refer to “2-5. White Balance Adjustment
on servicing”.)

2) When other boards than above are replaced

No particular adjustments are needed.

1.

Enter the Service Mode. (Refer to “2-1-2. Service
Mode Setting”.)

2.

Set Other: 01/Iris Adj in the Device Menu to 1.

3.

Change the value of Other: 02/Iris Open Reg.

4.

Change the value of Other: 03/Iris Close Reg.

5.

Return Other: 01/Iris Adj in the Device Menu to 0.

6.

Perform Save to Memory.

1.

Input the 720/60P  flat-field to the component termi-
nal.

2.

Enter the Service Mode. (Refer to “2-1-2. Service
Mode Setting”.)

3.

Enter the W/B mode in the Device Menu.

4.

Change the values of Gain R/G/B and Bias R/G/B in
each mode (High/Middle/Low/Custom1/Custom2/
Custom3).

5.

Perform Save to Memory.

* W/B data has a memory for each of the three IRIS modes (AUTO1/2,

Manual, and OFF for AW15; and AUTO, ON, and OFF for AW10).
Perform the above steps for each IRIS mode.

6.

Input the computer signal to input A, and copy all the
W/B adjustment values just as for Component.