Sony DPP-FP97 Service Manual ▷ View online
3-5
DPP-FP97
[Check and adjustment upon completion of
version upgrade]
version upgrade]
1.
While pressing the [ENTER] and [CANCEL] buttons simulta-
neously, press the [ON/STANDBY] button. (Service mode
starts.)
neously, press the [ON/STANDBY] button. (Service mode
starts.)
2.
Release all buttons when the initial screen of the service mode
is displayed on the LCD display.
1) Check the CHECKSUM: value.
is displayed on the LCD display.
1) Check the CHECKSUM: value.
Check that the CHECKSUM value (hexadecimal value)
displayed on the screen is the same as the value of the firm-
ware name registered in ESI homepage.
displayed on the screen is the same as the value of the firm-
ware name registered in ESI homepage.
2) Check that the destination is not changed. (Destination is
displayed by XX of “DPP-FP97 (XX)” on the topmost line
of the service mode screen.)
of the service mode screen.)
3) If the destination is changed after version upgrade is com-
pleted, change the destination.
For the procedure of the Color display check, refer to Ser-
vice Manual “SECTION 3-2-2. Color display check”.
For the procedure of the Color display check, refer to Ser-
vice Manual “SECTION 3-2-2. Color display check”.
4) For the procedure of the destination change, refer to the
next paragraph [3-2-4. Setting of destination] shown be-
low.
low.
3-2-4. SETTING OF DESTINATION
1.
While pressing the [ENTER] and [CANCEL] buttons simulta-
neously, press the [ON/STANDBY] button. (Service mode
starts.)
neously, press the [ON/STANDBY] button. (Service mode
starts.)
2.
Release all buttons when the initial screen of the service mode
is displayed on the LCD display.
is displayed on the LCD display.
3.
Press the DIRECTION button (F) several times to move the
cursor to [Select Model], and press [ENTER] button.
cursor to [Select Model], and press [ENTER] button.
4.
Move the cursor to the desired destination by using the DI-
RECTION buttons (f, F, g, G) and press [ENTER] button.
RECTION buttons (f, F, g, G) and press [ENTER] button.
5.
Press the DIRECTION button (f) several times to return to
the initial screen (on which “DPP-FP97 (XX)” is displayed) of
the service mode to confirm that the destination is changed.
the initial screen (on which “DPP-FP97 (XX)” is displayed) of
the service mode to confirm that the destination is changed.
6.
Turn off the power and disconnect the power cord from the
receptacle.
receptacle.
3-3. CHECK
3-3-1. FAN OPERATION CHECK
Operation of fan can be check as follows:
Procedure:
1.
Start the service mode. (Refer to Section 3-1-1.)
2.
Press the [PRINT] button on the service mode startup screen.
3.
Check that the fan rotating sound changes in the following or-
der starting from Low speed
der starting from Low speed
→ High speed → Stop by every
pressing of the [PRINT] button.
4.
Quit the service mode. (Refer to Section 3-1-1.)
3-3-2. BUTTON/LED/TRAY SENSOR/RIBBON
SENSOR OPERATION CHECK
The operation of each button, LED and sensors can be checked.
Note:
After the machine enters this mode once, it cannot exit this
mode until the “Button operation check” is completed.
mode until the “Button operation check” is completed.
Procedure:
1.
Start the service mode. (Refer to Section 3-1-1.)
2.
Select “Button Test” using the DIRECTION buttons (f, F)
and press the [ENTER] button.
The following screen is displayed
and press the [ENTER] button.
The following screen is displayed
Button operation check
Press the button on the operation panel of this unit. The pressed
button indication on the LCD of main unit lights in yellow. The
following screen shows that the [MENU] button is pressed.
button indication on the LCD of main unit lights in yellow. The
following screen shows that the [MENU] button is pressed.
When all 11 buttons are pressed one button after another, all button
indications on the screen light in red.
indications on the screen light in red.
DPP-FP97 (CED)
CHECKSUM: XXXXXXXX (H)
DATE: DEC 4 2008 15:27:21
USB SERIAL NO: 05000001
H TEMP: 28.7 / R TEMP: 27.9
Print Calibrate
LCD Calibrate
HDMI Test
Select Model
CEC/Freq Test
USB Test
Card Test
Button Test
- -
- -
A: - - B: - -
????????
????????
- -
CED
3-6
DPP-FP97
3-3-3. IMAGE READING CHECK FROM
MEMORY CARD
Image reading from Memory Stick or Memory Stick Duo, SD card
or CF card and xD-Picture card can be checked. (If it is JPG, the
image is arbitrary.)
or CF card and xD-Picture card can be checked. (If it is JPG, the
image is arbitrary.)
Preparation:
Place the JPEG file in the root directory of a Memory Stick.
(Filename: MS.jpg)
Place the JPEG file in the root directory of an SD card.
(Filename: SD.jpg) (Use the LOCK OFFed card.)
Place the JPEG file in the root directory of a CF card.
(Filename: CF.jpg)
Place the JPEG file in the root directory of a xD-Picture card.
(Filename: XD.jpg)
Procedure:
1.
Start the service mode. (Refer to Section 3-1-1.)
2.
Select “Card Test” by using the DIRECTION buttons (f, F)
and press the [ENTER] button.
and press the [ENTER] button.
3.
Insert the Memory Stick that is prepared separately, and con-
firm the image of MS.jpg is displayed.
firm the image of MS.jpg is displayed.
4.
Pull out the Memory Stick, and insert the SD card that is pre-
pared separately, and confirm the image of SD.jpg is displayed.
pared separately, and confirm the image of SD.jpg is displayed.
5.
Pull out the SD card, and insert the xD-Picture card that is
prepared separately, and confirm the image of XD.jpg is dis-
played.
prepared separately, and confirm the image of XD.jpg is dis-
played.
6.
Pull out the xD-Picture card, and insert the CF card that is
prepared separately, and confirm the image of CF.jpg is dis-
played.
prepared separately, and confirm the image of CF.jpg is dis-
played.
HDMI Test
Select Model
CEC/Freq Test
USB Test
Card Test
Button Test
OK
- -
A: - - B: - -
????????
????????
- -
CED
When the checks of all buttons are completed without problem, the
initial screen of the service mode is displayed and “OK” is dis-
played to the right of “Button Test”.
initial screen of the service mode is displayed and “OK” is dis-
played to the right of “Button Test”.
3.
Quit the service mode. (Refer to Section 3-1-1.).
LED operation check
Check that the “PRINT LED” and the “Access LED” light up dur-
ing the “Button Test”, and then flash before turning off when the
“Button Test” is completed.
ing the “Button Test”, and then flash before turning off when the
“Button Test” is completed.
Ribbon sensor operation check
Whether the ribbons are correctly recognized or not can be checked.
Check to see that the ribbon type display on the screen agrees with
the inserted ribbon when different types of ribbon are inserted.
Check to see that the ribbon type display on the screen agrees with
the inserted ribbon when different types of ribbon are inserted.
Print Pack Size
Display
P size
Post
L size
L
Not installed
None
Tray sensor operation check
Whether the trays are correctly recognized or not can be checked.
Check to see that the tray type displayed on the screen agrees with
the inserted tray when different types of tray are inserted.
Check to see that the tray type displayed on the screen agrees with
the inserted tray when different types of tray are inserted.
Print Pack Size
Display
P size
Post
L size
L
Not installed
None
3-7
DPP-FP97
Even if the button is not pushed, it is judged that the card is insert-
ed. Insert all of the one card, and confirm it.
ed. Insert all of the one card, and confirm it.
7.
When all memory cards reading are completed, press the [EN-
TER] button.
TER] button.
• When all memory cards work normally so that images can
be read without error, the character OK is displayed on the
right of “Card Test” on the service mode startup screen.
right of “Card Test” on the service mode startup screen.
• If a memory card is not set, or if image is not contained in a
memory card, or image cannot be read from a memory card,
background of the screen becomes red and the character NG
(No Good) is displayed in the left bottom of a screen.
background of the screen becomes red and the character NG
(No Good) is displayed in the left bottom of a screen.
• If either a memory card is NG (No Good), the character NG
(No Good) is displayed on the right of “Card Test” on the
service mode startup screen.
service mode startup screen.
8.
Quit the service mode. (Refer to Section 3-1-1.)
3-3-4. USB HOST/DEVICE COMMUNICATION
CHECK
The digital camera for PictBridge or the digital camera , the USB
memory and the photo storage for the mass storage are connected
with the terminal PictBridge/EXT INTERFACE of this machine,
and confirm that this machine reacts.
This machine connects with Windows PC that installs software by
USB cable, and confirm that Windows PC reacts.
memory and the photo storage for the mass storage are connected
with the terminal PictBridge/EXT INTERFACE of this machine,
and confirm that this machine reacts.
This machine connects with Windows PC that installs software by
USB cable, and confirm that Windows PC reacts.
3-3-5. Output confirmation of HDMI
• Check of HDMI OUT
Confirm the monitor corresponds to the HDMI input is connected
with this unit HDMI OUT and the image is displayed in the HDMI
monitor without trouble.
with this unit HDMI OUT and the image is displayed in the HDMI
monitor without trouble.
• Check of HDMI CEC
When there is a monitor corresponds to CEC
Confirm the monitor for CEC is connected with this machine, and
CEC can control without trouble.
CEC can control without trouble.
When there is no monitor corresponds to CEC
It is possible to make this unit work by setting the service mode as
SINK jig for the HDMI CEC check.
Prepare this machine “B” (DPP-FP97 other than the service set) for
the HDMI CEC check, set the SINK jig by the following proce-
dures, and check HDMI CEC when there is no monitor for CEC.
SINK jig for the HDMI CEC check.
Prepare this machine “B” (DPP-FP97 other than the service set) for
the HDMI CEC check, set the SINK jig by the following proce-
dures, and check HDMI CEC when there is no monitor for CEC.
Procedure:
Setting of SINK jig
Setting of SINK jig
1.
Prepare another machine (this machine “B” as follows) be-
sides this machine that checks CEC.
(The SINK equipment for corresponds to CEC )
sides this machine that checks CEC.
(The SINK equipment for corresponds to CEC )
2.
Start this machine B in the service mode. (Refer to Section 3-
1-1.)
1-1.)
3.
Select “System Setting” with the DIRECTION buttons (f, F),
and push the [ENTER] button.
and push the [ENTER] button.
HDMI Test
Select Model
CEC/Freq Test
USB Test
Card Test
Button Test
- -
OK
A: - - B: - -
????????
????????
- -
CED
HDMI Test
Select Model
CEC/Freq Test
USB Test
Card Test
Button Test
- -
NG
A: - - B: - -
????????
????????
- -
CED
System Info
System Setting
Media Check
USB Host Test
3-8
DPP-FP97
4.
Push the sending decision button to CEC JIGU MODE with
the DIRECTION buttons (f, F). Set to turning on with the
DIRECTION buttons (f, F) and push the [ENTER] button.
Push the DIRECTION buttons (f, F) select to “Exit”, and end
System Setting.
Under such a condition, this unit B is made to the HDMI CEC
SINK jig and comes to work.
the DIRECTION buttons (f, F). Set to turning on with the
DIRECTION buttons (f, F) and push the [ENTER] button.
Push the DIRECTION buttons (f, F) select to “Exit”, and end
System Setting.
Under such a condition, this unit B is made to the HDMI CEC
SINK jig and comes to work.
*
CEC JIGU MODE cannot be turned off as long as this unit
power supply is not turned off when setting it to turning on
once. If the power supply of this machine is turned off once,
CEC JIGU MODE is automatically turned off.
power supply is not turned off when setting it to turning on
once. If the power supply of this machine is turned off once,
CEC JIGU MODE is automatically turned off.
Note:
Please do not connect it with the SINK device like HDMI
monitor at CEC JIGU MODE ON.
monitor at CEC JIGU MODE ON.
HDMI CEC check
1.
Start this unit in the service mode. (Refer to Section 3-1-1. )
2.
“CEC/Freq Test” is selected with the DIRECTION buttons (f,
F), and the [ENTER] button is pushed.
F), and the [ENTER] button is pushed.
3.
Connect this machine and the SINK jig (this unit “B”) with the
HDMI cable and push the [ENTER] button of this unit.
Confirm becoming the display of “CEC Test: OK”.
HDMI cable and push the [ENTER] button of this unit.
Confirm becoming the display of “CEC Test: OK”.
4.
Push the cancel button.
When CEC Test is OK, “OK” is displayed at the right of “CEC/
Freq Test” of the service mode start screen.
When CEC Test is OK, “OK” is displayed at the right of “CEC/
Freq Test” of the service mode start screen.
When CEC Test is NG
“NG” is displayed at the right of “CEC/Freq Test” of the ser-
vice mode start screen.
vice mode start screen.
5.
End the service mode. (Refer to clause 3-1-1. )
*** System Setting ***
APP DebOut Level
0
API DebOut Level
3
PrinterLot
0
Data LogOut
Off
Numbering
Off
ScrnCapture
Off
RibHagashi step
158
NewSequence
2
HS
On
Button Test Cut
Off
HDMI Resolution
Auto
HDMI Polling TV
On
HDMI One TouchPlayEx
Off
CEC JIGU MODE
On
Exit
HDMI Test
Select Model
CEC / Freq Test
USB Test
Card Test
Button Test
- -
OK
A: - - B: - -
????????
????????
- -
CED
HDMI Test
Select Model
CEC / Freq Test
USB Test
Card Test
Button Test
- -
OK
A: - - B: - -
????????
????????
OK
CED
HDMI Test
Select Model
CEC / Freq Test
USB Test
Card Test
Button Test
- -
- -
A: - - B: - -
????????
????????
NG
CED
Click on the first or last page to see other DPP-FP97 service manuals if exist.