Sony DPP-F800 Service Manual ▷ View online
DPP-F800
1-3
ns: not supplied
1-3. HINGE SECTION
Note
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
0
101
1-855-049-11 DC FAN (Note1)
102
4-167-339-01 SCREW +BW 2X4 TYPE2
103
4-266-318-01 SERVICE, TOP COVER ASSY (BLACK)
103
4-266-318-11 SERVICE, TOP COVER ASSY (WHITE)
104
A-1803-098-A SERVICE, REAR COVER ASSY BE (BLACK)
104
A-1803-099-A SERVICE, REAR COVER ASSY WE (WHITE)
105
4-167-920-01 SCREW +P M3X5
Note2: Method for Removing the Hinge Assy
Note that the Hinge Assy should be attached from the Rear
Cover Assy side also when assembling.
(1) Open the Rear Cover Assy.
Rear Cover Assy
(2) Remove two screws.
Remove the Rear Cover Assy from the Top Cover Assy.
Screw
(3) Remove six screws.
Remove the Hinge Assy from the Top Cover Assy.
Screw
Note1: Refer to “Assembly-3: Method of attachment of the DC Fan”
when you assemble.
103
(For connection to the Main
PWB Assy, see page 1-2.)
(Note1)
101
104
ns (Note2)
ns (Note2)
ns
ns
ns
ns
ns
105
102
105
105
105
DPP-F800
1-4E
1-4. ACCESSORIES
• Refer to page 1-1 for mark 0.
Note: This item is supplied with the unit as an accessory,
but is not prepared as a service part.
Operating Instructions
Read This First
(Note)
・(Only for destination Japanese model)
英語・韓国語・中国語のみ部品供給可能です。
英語・韓国語・中国語のみ部品供給可能です。
Remote commander
(RMT-DPF4)
Cleaning cartridge
(Used for cleaning inside the printer.)
X-2055-849-2
Cleaning sheet
(Used for cleaning inside the printer.)
3-094-075-02
0
1-489-218-21
4-208-449-11 (ENGLISH)
∗ 4-208-449-21 (FRENCH)
∗ 4-208-449-61 (SPANISH)
∗ 4-208-449-71 (PORTUGUESE)
∗ 4-208-449-31 (GERMAN)
∗ 4-208-449-41 (DUTCH)
∗ 4-208-449-51 (ITALIAN)
∗ 4-208-449-81 (RUSSIAN)
∗ 4-208-449-91 (UKRAINIAN)
∗ 4-208-450-11 (ARABIC)
∗ 4-208-450-21 (PERSIAN)
4-208-450-31 (KOREAN)
4-208-450-41 (SIMPLIFIED CHINESE) (JE, E (Saudi, Hong Kong))
∗
4-208-450-51 (TRADITIONAL CHINESE)
4-208-450-61 (SIMPLIFIED CHINESE) (CH)
CD-ROM
(Windows Printer Driver Software
Ver.1.0 and PMB (Picture Motion Browser)
Ver.5.2)
4-260-720-01
Conversion (2P) Adaptor
0
1-569-007-12 (JE)
0
1-569-008-33 (E (Central & South America))
Paper tray
A-1239-944-A (EXCEPT CH (WHITE))
A-1252-126-A (EXCEPT CH (BLACK))
A-1487-928-A (CH (WHITE))
A-1512-250-A (CH (BLACK))
AC Adaptor (AC-S2422)
0
1-480-108-51
Power cord
0
1-829-810-21 (CND)
0
1-833-889-11 (AEP, E (EXCEPT Saudi, Hong Kong))
0
1-833-890-32 (CH)
0
1-833-892-41 (KR)
0
1-834-852-11 (TW)
0
1-834-950-22 (E (Saudi, Hong Kong), UK)
0
1-836-251-11 (JE)
2-190-622-01
Tray Sheet
(Note)
Ver.1.1 2011.02
The changed portions from
Ver.1.0 are shown in blue.
DPP-F800
2-1E
2. ASSEMBLY
LCD metal
frame edge
frame edge
0 to 3.9 mm
0 to 11 mm
LCD metal
frame edge
frame edge
0 to 6.9 mm
0 to 5.8 mm
0 to 12 mm
LCD Sponge L
LCD Sponge L
LCD Sponge S
LCD Sponge S
LCD Assy
Assembly-1: Putting position of the LCD Sponge S
and the LCD Sponge L
Label side
Top Cover Assy
DC Fan
Tighten the screw without involving the harness.
Assembly-3: Method for attaching of the DC Fan
Slot
Put the DC Fan in the frame on the Top Cover Assy with
the label side downward and pass the harness through
the slot, then tighten two screws without involving the
harness.
the label side downward and pass the harness through
the slot, then tighten two screws without involving the
harness.
LCD Assy
Rear Cover Assy
Assembly-2: Routing the LCD Assy harness
Routing outside the rib
Route the LCD Assy harness outside the ribs of
the Rear Cover Assy without being wedged under
the LCD Assy.
the Rear Cover Assy without being wedged under
the LCD Assy.
Harness
Bottom Cover
Thermal Printer Assy
Assembly-4: Method for installing
the Thermal Printer Assy
Install the Thermal Printer Assy into the Bottom Cover
while sliding it in the direction indicated with arrow as
shown below.
while sliding it in the direction indicated with arrow as
shown below.
Cable of the DC IN Board Assy
Bottom Cover
Downmost
Uppermost
Claw
Assembly-5: Routing the cable and harnesses
Note: The arrangement of the cable, flexible board and
harnesses is important that will affect routing
operation in the post process.
Especially, the cable of the DC IN Board Assy
should be arranged from the downmost position
to the uppermost position as shown below.
operation in the post process.
Especially, the cable of the DC IN Board Assy
should be arranged from the downmost position
to the uppermost position as shown below.
5-1. Pass the cable of the DC IN Board Assy through the
guide indicated with arrow.
5-2. Arrange the cable, flexible board and harnesses
as shown below.
5-3. Hook the thin color harnesses together on the claw
and pass them inside the guide indicated with arrow.
Cable of the
DC IN Board Assy
DC IN Board Assy
5-4. Hook the cable of DC IN Board Assy on the claw of
the Rear Cover Assy.
5-5. Turn over the Main PWB Assy to attach it to the Rear
Cover Assy and pass the cable of the DC IN Board
Assy outside the guide 1 and inside the guide 2
indicated with arrow.
Assy outside the guide 1 and inside the guide 2
indicated with arrow.
Claw
Cable of the
DC IN Board Assy
DC IN Board Assy
DC IN Board Assy
Rear Cover Assy
2
1
DPP-F800
3-1E
3-1. Adjustment Required When Replacing Thermal
Printer Or Board
The head voltage needs to be adjusted when the “Thermal
Printer Assy” or “Main PWB Assy” is replaced.
Printer Assy” or “Main PWB Assy” is replaced.
Head Voltage Adjustment
4. Use a ceramic screwdriver to turn the head voltage adjustment
variable resistor (VR1) to adjust the head voltage to the value you
have written down in the preparation step.
have written down in the preparation step.
3. Connect the plus lead of the digital voltmeter to the head voltage
measurement land (HDR) land and measure the head voltage.
2. Connect the minus lead of the digital voltmeter to any point of the
three GND points as shown below.
6. After the head voltage adjustment, disconnect the power cord from
the socket and remove the solder.
5. Repeat steps 2. through 4. to adjust the head voltage to within a
tolerance of ± 0.1 V.
7. After assembling the set, print and check the print results.
3. ADJUSTMENT
Adjustment Procedure:
1. Connect the power cable to the main board, and after plugging the
AC adaptor (AC-S 2422) attached to the set into the DC IN 24V
terminal, insert the power cord into the power socket.
terminal, insert the power cord into the power socket.
Preparation:
• Write down the numerical value (head voltage) written on the label
of the HEAD section of the thermal printer.
Example) 15.01
Note:
・
You can enter into the test mode and the output of the head voltage
turns on only during the short-circuit time.
・
Make sure to remove the solder to release the test mode after the
adjustment.
• Short circuit on two points of the land by soldering shown below to
enter into the test mode.
Note: When printing, please pay attention to the amount of space in the
back so as not to block the paper outlet behind the set.
Note: If the voltage is lowered, it may take some time for the voltage to
change.
GND point
Head voltage measurement land (HDR)
Write down the head voltage here
Land (two points)
Head voltage adjustment variable resistor (VR1)
Main PWB Assy DC IN 24V terminal
Power cable
AC adaptor
To power
socket
Display