Sony HDR-TG1 / HDR-TG1E / HDR-TG3E (serv.man2) Service Manual ▷ View online
1-2
ENGLISH
JAPANESE
ENGLISH
JAPANESE
HDR-TG1/TG1E/TG3E_L2
1-3-3. Self-diagnosis Code Table
C
C
C
C
E
E
E
E
E
E
E
Block
Function
0
4
1
3
1
3
3
2
2
0
6
1
6
1
6
2
6
2
9
1
9
4
Detailed
Code
0
0
0
1
0
2
6
0
0
0
1
0
1
1
0
0
0
1
0
1
0
0
Symptom/State
Non-standard battery is used.
“Memory Stick Duo” is unformatted.
“Memory Stick Duo” is broken.
“Memory Stick Duo” is broken.
Access error
Difficult to adjust focus
(Cannot initialize focus)
(Cannot initialize focus)
Flash memory data are rewritten.
Zoom operations fault
(Cannot initialize zoom lens.)
(Cannot initialize zoom lens.)
The abnormalities in initialization of
the focus lens and the abnormalities in
initialization of the zoom lens occurred
simultaneously.
the focus lens and the abnormalities in
initialization of the zoom lens occurred
simultaneously.
Handshake correction function does not
work well. (With PITCH angular
velocity sensor output stopped.)
work well. (With PITCH angular
velocity sensor output stopped.)
Handshake correction function does not
work well. (With YAW angular velocity
sensor output stopped.)
work well. (With YAW angular velocity
sensor output stopped.)
Abnormality when flash is being charged.
Fault of writing to or erasing the flash
memory
memory
Self-diagnosis Code
Repaired b
y:
Note 1:
Refer to Service manual, ADJ (“1-3. DESTINATION DATA WRITE”).
Note 2:
When the lens block was replaced, execute a necessary adjustment items referring to Service Manual, ADJ.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the handheld operation.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the handheld operation.
Correction
Use the InfoLITHIUM battery.
Format the “Memory Stick Duo”.
Insert a new “Memory Stick Duo”.
Insert a new “Memory Stick Duo”.
Remove the power source.
Reconnect it again and operate your camcorder again.
Reconnect it again and operate your camcorder again.
Retry turn the power on by the power switch. If it does not
recover, check the focus MR sensor of lens block (pin 1, 2 of
CN5202 on the LD-235 board). If it is OK, check the focus
motor drive IC (IC5201 on the LD-235 board).
recover, check the focus MR sensor of lens block (pin 1, 2 of
CN5202 on the LD-235 board). If it is OK, check the focus
motor drive IC (IC5201 on the LD-235 board).
Make flash memory data correct value. (Note 1)
Inspect the lens block zoom reset sensor (pin wf of CN5202 on
the LD-235 board) when zooming is performed when the zoom
lever is operated, and the zoom motor drive circuit (IC5201 on
the LD-235 board) when zooming is not performed.
the LD-235 board) when zooming is performed when the zoom
lever is operated, and the zoom motor drive circuit (IC5201 on
the LD-235 board) when zooming is not performed.
Check both C : 32 : 60 and E : 61 : 10 of the self-diagnosis code.
Inspect PITCH/YAW angular velocity sensors (SE6602 on the
SE-174 board) peripheral circuits.
SE-174 board) peripheral circuits.
Inspect PITCH/YAW angular velocity sensors (SE6602 on the
SE-174 board) peripheral circuits.
SE-174 board) peripheral circuits.
Checking of flash unit or replacement of flash unit.
Inspect the flash memory (IC2101 on the VC-522 board).
1-3
ENGLISH
JAPANESE
ENGLISH
JAPANESE
HDR-TG1/TG1E/TG3E_L2
1-4-1. Precaution on ordering the Cabinet (L)
The model display adopts the laser printing method.
Therefore, the Cabinet (L) for replacement differs depending on
the destination.
As similar displays are provided, choose the suitable one for order.
Therefore, the Cabinet (L) for replacement differs depending on
the destination.
As similar displays are provided, choose the suitable one for order.
Note:
After replacing the Cabinet (L), the serial number for it will
be changed to the one exclusive for service use.
Inform a customer of the serial number change and change
the serial number in the repair data.
be changed to the one exclusive for service use.
Inform a customer of the serial number change and change
the serial number in the repair data.
1-4. PRECAUTION ON REPLACING THE CABINET (L)
Serial No.
HDR-TG1 (J)
HDR-TG1 (KR)
A-1542-400-A
Serial No.
Serial No.
Serial No.
Serial No.
Serial No.
Serial No.
Serial No.
Serial No.
CABINET (L (TG1-J1)),
SERVICE
SERVICE
HDR-TG1 (US)
HDR-TG1 (CND)
A-1542-402-A CABINET (L (TG1-U2)),
SERVICE
A-1542-403-A CABINET (L (TG1-CA2)),
SERVICE
A-1542-404-A CABINET (L (TG1-KR2)),
SERVICE
CABINET (L (TG1-E23)),
SERVICE
SERVICE
CABINET (L (TG1-CEL)),
SERVICE
SERVICE
HDR-TG1 (E, JE)
A-1542-405-A
HDR-TG1E (NE)
CABINET (L (TG3-CEL)),
SERVICE
SERVICE
HDR-TG3E (NE)
CABINET (L (TG3-CEN)),
SERVICE
SERVICE
HDR-TG3E (AEP, UK)
A-1542-406-A
A-1542-407-A
A-1542-408-A
A-1542-409-A
A-1542-410-A
Part No.
Description
Part No.
Description
Part No.
Description
Part No.
Description
Part No.
Description
Part No.
Description
Part No.
Serial No.
Part No.
Description
Part No.
Description
Part No.
Description
Description
CABINET (L (E34)),
SERVICE
SERVICE
CABINET (L (CN2)),
SERVICE
SERVICE
HDR-TG1E (E, HK, AUS, JE)
HDR-TG1E (CH)
1-4
ENGLISH
JAPANESE
ENGLISH
JAPANESE
HDR-TG1/TG1E/TG3E_L2
1-4-2. Precaution on Replacing the Cabinet (L) for J Models
The year of manufacture on the labels should be the same as the previous Cabinet (L) (circled portions shown on the below).
Example: For the figure below, attach the “Made of 08 years” label.
Example: For the figure below, attach the “Made of 08 years” label.
* The replacement label and “inset (how to affix)” are supplied together with Cabinet (L) for service.
1-4-3. Precaution on Replacing the Cabinet (L) for US Models
The date of manufacture and the manufacturer on the labels should be the same as the previous Cabinet (L) (circled portions shown on the
below).
Example: For the figure below, attach the “8A” and “SKD” labels.
below).
Example: For the figure below, attach the “8A” and “SKD” labels.
* The replacement labels and “inset (how to affix)” are supplied together with Cabinet (L) for service.
1-4-4. Precaution on Replacing the Cabinet (L) for KR Models
The date of manufacture on the labels should be the same as the previous Cabinet (L) (circled portions shown on the below).
Example: For the figure below, attach the “2008.2” label.
Example: For the figure below, attach the “2008.2” label.
* The replacement label and “inset (how to affix)” are supplied together with Cabinet (L) for service.
* Affix the label
* Manufacturing year
* Affix the label
* Manufacturing year
* Factory
* Affix the label
* Manufacturing year
1-5
ENGLISH
JAPANESE
ENGLISH
JAPANESE
HDR-TG1/TG1E/TG3E_L2
1. SERVICE NOTE
1-1. 修理時の電源供給について
本機では，安定化電源（8.4Vdc）からバッテリ端子に電源を供給した場合，約10秒後にシャットオフし，動作しなくなります。
これを避けるため，下記の方法を用いてください。
方法：
DC入力端子を使用する。（ACアダプタ（AC-L200/L200B）を使用する。）
DC入力端子を使用する。（ACアダプタ（AC-L200/L200B）を使用する。）
1-2. VC-522基板交換時の注意
仕向けデータ
補修用基板と交換する時，補修用基板に書かれている仕向けデータは元の設定と違っている場合があります。
ADJ編を参照して，「DESTINATION DATA WRITE」を行ってください。
USBシリアルNo.
セットは，1台毎に異なる固有のID（USB Serial No.）を書き込んだ後，出荷されています。
新品の補修用基板には，このIDが書き込まれていないので，基板交換後にIDを入力する必要があります。
ADJ編を参照して，「USB SERIAL No. INPUT」を行ってください。
1-3. 自己診断機能
1-3-1. 自己診断機能について
本機の動作に不具合が生じたとき，自己診断機能が働き，
本機の動作に不具合が生じたとき，自己診断機能が働き，
ビューファインダまたはL C D 画面に，どう処置したらよい
か判断できる表示を行います。自己診断機能については取扱
説明書にも掲載されています。
1-3-2. 自己診断表示
本機の動作に不具合が生じたとき，ビューファインダまたは
LCD画面のカウンタ表示部分がアルファベットと数字の4桁
表示になり，3.2Hzで点滅します。この5文字の表示によっ
て対応者分類および不具合の生じたブロックの分類，不具合
の詳細コードを示します。
1 1
3 1
C
対応者分類
「1 -3 -3 . 自己診断コード表」
を参照
対応方法の違いにより分類
例
例
31 ･･ ･テープを入れ直す
32 ･･ ･電源を入れ直す
ブロック分類
詳細コード
3.2Hz点滅
C ：お客さま自身で対応
H ：販売店で対応
E ：サービスエンジニア
H ：販売店で対応
E ：サービスエンジニア
で対応
ビューファインダまたはLCD画面
C : 3 1 : 1 1
Click on the first or last page to see other HDR-TG1 / HDR-TG1E / HDR-TG3E (serv.man2) service manuals if exist.