DOWNLOAD Sony HDR-TD30 / HDR-TD30E / HDR-TD30V / HDR-TD30VE (serv.man2) Service Manual ↓ Size: 5.55 MB | Pages: 22 in PDF or view online for FREE

HDR-TD30/TD30E/TD30V/TD30VE_L2

1-2

3)  Search the model whose new Destination Data file you want to get on the TISS homepage.
 

When the Destination Data file has been updated, a file with a name “Destination File For ‘model name’.zip” is registered.

(Example) Destination File For DSC-WX50.zip

Furthermore, the version supported by the Destination Data file is shown in the Remarks column.

Note : If the Destination Data file has not been updated, contact the Service Headquarters.

 4)  Download the Destination Data file of the relevant model and unzip the file.

5)  Execute “DESTINATION DATA WRITE” in the Adjust tab of the Adjust manual.
 

Click the [START] button.

6)  Click the [File Update] button in the window.
 

7)  A file selection screen opens. Select the Destination Data file to be added and click the [Open] button.
 

8)  When the file has been successfully added, the following window opens.
 

9)  Check the Destination Ver. window and confirm that the version has been updated.

Destination Ver. window

HDR-TD30/TD30E/TD30V/TD30VE_L2

1-3

When you replace to the repairing board, write down the sensitivity displayed on the angular velocity sensor SE7501 (PITCH/YAW).
Start the Adjust Manual in the Adjust Station and execute the “GYRO sensor sensitivity adj”.

Note: The sensor sensitivity of SE7501 (PITCH/YAW) on JK-404 board is written only repair parts.

When replacing the lens, write down the PITCH/YAW data given on the data sheet of the replacement lens for service.
Start the Adjust Manual in the Adjust Station and execute the “GYRO sensor sensitivity Adj”.

PITCH data

YAW data

L2
L1

P.PP/Y.YY

P.PP/Y

.YY

SE7501

JK-404 BOARD (SIDE A)

YY

PP

G1

G2

PP: PITCH sensor sensitivity
YY: YAW sensor sensitivity

When problems occur while the unit is operating, the self-diagnosis 
function starts working, and displays on the Viewfinder or the LCD 
screen what to do.
This function consists of two display; self-diagnosis display and service 
mode display.Details of the self-diagnosis functions are provided in the 
Instruction manual.

When problems occur while the unit is operating, the counter of the 
Viewfinder or the LCD screen shows a 4-digit display consisting of an 
alphabet and numbers,
which blinks at 3.2 Hz. This 5-character display indicates the “repaired 
by:”, “block” in which the problem occurred, and “detailed code”of the 
problem.

0 0

3 2

C

Repaired by:

Refer to “1-6-3. Self-diagnosis Code Tabl e”.

Indicates the appropriate

step to be taken.

E.g.
13 ....
32 ....Turn on power again.

Block

Detailed Code

Blinks at 3.2 Hz

C : Corrected by customer

E : Corrected by service

engineer

Format the “memory card”.

LCD screen

Self-diagnosis Code

Symptom/State

Correction

Repaired by:

Block

Function

Detailed

Code

C

0

4

0

0

Non-standard battery is used.

Use the InfoLITHIUM battery.

C

0

6

0

0

The battery pack temperature is high.

Change the battery pack or place it in a cool place.

C

1

3

0

1

Memory card is unformatted.
Memory card is broken.

Format the memory card.
Insert a new memory card.

C

1

3

0

2

Access error

Remove the power source. Reconnect it again and operate your cam-
corder again.

C

1

3

0

3

Access error (External media)

Turn power off and turn power on again.

C

1

3

0

4

Drive fault (External media)

Turn power off and turn power on again.

C

E

3

2

6

1

6

0

0

0

Difficult to adjust focus
(Cannot initialize focus)

Retry turn the power on by the power switch. If it does not recover, check 
the focus MR sensor of lens device (pin 1 to 4 of CN1012 or pin 1 to 
4

 of CN1014 on the VC-655 board). If it is OK, check the focus motor 

drive IC (IC5501 or IC5701 on the VC-655 board).

E

2

0

0

0

Flash memory data are rewritten.

Make flash memory data correct value. (Note 1)

E

3

1

0

0

Drive fault

Turn power off and turn power on again.

E

6

1

1

0

Zoom operations fault

(Cannot initialize zoom lens.)

Inspect the lens device zoom reset signal (pin eg of CN1012 or pin eg 

of CN1014 on the VC-655 board) when zooming is performed when the 

zoom lever is operated, and the zoom motor drive circuit (IC5701 on the 

VC-655 board) when zooming is not performed.

Note 1: Start the Adjust Manual in the Adjust Station and refer to the “DESTINATON DATA WRITE”.

(                                           )

HDR-TD30/TD30E/TD30V/TD30VE_L2

1-4

Self-diagnosis Code

Symptom/State

Correction

Repaired by:

Block

Function

Detailed

Code

E

6

1

1

1

The abnormalities in initialization of the focus 

lens and the abnormalities in initialization of 

the zoom lens occurred simultaneously.

Check both C: 32: 60 and E: 61: 10 of the self-diagnosis code.

E

6

1

3

0

Reset position detection error on the stepper 

iris initializing

Turn the power on to open lens barrier. Disconnect the battery or power 

cord, and then connect again.

Confirm that the iris blades in lens are working.

If iris blades do not working, check the iris motor drive IC in lens 

drive block (CN1012 pin wg, wh or CN1014 pin wg, wh on VC-655 

board).

If iris blades work normally, confirm that they are closing completely 

and confirm following item.
･  Case of the iris blades do not close normally, replace the lens device.
･  Case of “E: 61: 30” is appeared and iris blades closed completely.

  Confirm that communication with lens device is normal.
･ Case of LCD is not displayed normally, check that connection 

between lens device (CM-123 board) and CN1007 or CN1011 on 

VC-655 board by FP-1505 flexible board.

･  Case of LCD is displayed normally, replace the lens device.

E

6

2

0

0

Handshake correction function does not work 

well. (With PITCH angular velocity sensor 

output stopped.)

Inspect PITCH angular velocity sensors (SE7501 on the JK-404 board) 

peripheral circuits.

E

6

2

0

1

Handshake correction function does not work 

well. (With YAW angular velocity sensor 

output stopped.)

Inspect YAW angular velocity sensors (SE7501 on the JK-404 board) 

peripheral circuits.

E

6

2

0

2

Abnormality of IC for steadyshot.

Refer to “1-7-1. E : 62 : 02 (Abnormality of IC for Steadyshot) Oc-

curred”.

E

6

2

0

3

IC for steadyshot and micro controller com-

munication abnormality among.

Inspect the steadyshot circuit (IC5501 on the VC-655 board).

E

6

2

0

4

Image vibration correction during 

handshake function does not work.

Inspect the image vibration angular velocity sensors (SE7701 on the 

VC-655 board) peripheral circuits.

E

6

2

1

0

Shift lens initializing failure.

Replacement of lens device. (Note 3) If an error occurs again, replace 

the VC-655 board.

E

6

2

1

1

Shift lens overheating (Pitch)

Refer to “1-7-2. E : 62 : 11 [Shift Lens Overheating (Pitch)] Occurred”.

E

6

2

1

2

Shift lens overheating (Yaw)

Refer to “1-7-3. E : 62 : 12 [Shift Lens Overheating (Yaw)] Occurred”.

E

6

2

2

0

Abnormality of thermistor.

Refer to “1-7-4. E : 62 : 20 [Abnormality of Thermistor] Occurred”.

E

9

1

0

1

Abnormality when flash is being charged.

Checking of flash unit or replacement of FP-1501 flexible board.

E

9

1

0

2

Abnormality of flash unit.

Checking of flash unit or replacement of FP-1501 flexible board.

E

9

1

0

3

Abnormality of flash unit Temperature 

detection.

Checking of flash unit or replacement of FP-1501 flexible board.

E

9

2

0

1

Battery current value goes over the max 

discharge current

Check the remaining battery power because this symptom maybe 

depended on the remaining battery level, and confirm whether or 

not the symptom is occurred after replacing the battery. If the symp-

tom is still occurred, overhaul inspection is needed. Connect the 

CN8002 of MM-103 board with CN1001 of  VC-655 board.

Check each output of DC/DC converter (IC4301) on VC-655 board 

with the AC adaptor connected DC JACK (J001). 

(The minimum connection to periphery)

E

9

4

0

0

Fault of writing or erasing the flash memory

Inspect the flash memory (IC8101 on the MM-103 board).

E

9

4

0

1

Internal flash memory fault

Inspect the flash memory (IC8101 on the MM-103 board).

E

9

4

0

2

BGM data error

Check the CPU (IC1301 on the VC-655 board).

E

9

5

0

0

GPS hardware error

TD30V/TD30VE:

Check whether the FFC-277 flexible flat cable is broken, and check 

whether it is inserted imperfectly.

If there is no problem the flexible board, inspect or replacement of 

the GP-037 board.

E

9

6

0

0

Map area mount error

TD30V/TD30VE:

Inspect or replacement of the MM-103 board.

E

9

7

0

0

Projector  hardware error

Turn power off and turn power on again.

Note 2: Functions of codes with * mark are not provided in this unit.
Note 3: When the lens device was replaced, start the Adjust Manual in the Adjust Station and execute the necessary adjustment items.

After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the handheld operation.

C5525

C5526

C5527

C5528

C5529

R5506

C5530

C5531

C5532

IC5501

about 330 msec

Note: The length of low section will vary a little depending on the conditions.

Order

Procedure

1

Turn the power OFF.

2

While measuring with an oscilloscope the output voltage of R5506 in the periphery of IC5501 on the VC-655 board, turn the 
power ON to check that the output voltage immediately after the power on change as shown in Fig. 2.

3

If the output voltage change as shown in Fig. 2, replace the lens device (Note). If it does not change as shown in Fig. 2, inspect 
the camera control circuit (IC1601 of VC-655 board) periphery.

Note:  When the lens device was replaced, start the Adjust Manual in the Adjust Station and execute the necessary adjustment items.

After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the handheld operation.

*

HDR-TD30/TD30E/TD30V/TD30VE_L2

1-5

Order

AdjustBlock

AdjustCode

Order

1

If a caution occurs only in the 2D mode, perform the procedure beginning with step 6.

2

Start the Adjust Manual in the Adjust Station and execute the [Measure to E:62:11/12 for 2D] on the 
[SERVICE] tab in the 3D mode.

3

Check if the shift lens moves while setting the order 2.
If the shift lens does not move, replace the lens device (Note).
When the shift lens moved, proceed to the order 4.

4

While setting the order 1, measure with an oscilloscope the output voltage of C5531 and C5532 in 
the periphery of IC5501 on the VC-655 board to check the output voltage varies.

5

If the output voltage does not vary, replace the lens device (Note).
When the output voltage varied, proceed to the order 6.

6

Start the Adjust Manual in the Adjust Station and execute the [Measure to E:62:11/12 for 2D] on the 
[SERVICE] tab in the 2D mode.

7

Check if the shift lens moves while setting the order 6.
If the shift lens does not move, replace the lens device (Note).
When the shift lens moved, proceed to the order 8.

8

While setting the order 1, measure with an oscilloscope the output voltage of C5527 and C5528 in 
the periphery of IC5501 on the VC-655 board to check the output voltage varies.

9

If the output voltage does not vary, replace the lens device (Note).
When the output voltage varied, proceed to the order 10.

10

Turn the power OFF.

11

While measuring with an oscilloscope the output voltage of R5506 in the periphery of IC5501 on the
VC-655 board, turn the power ON to check that the output voltage immediately after the power on
change as shown in Fig. 2.

12

If the output voltage change as shown in Fig. 2, replace the lens device (Note).
If it does not change as shown in Fig. 2, inspect the camera control circuit (IC1301 of VC-655 board
and IC5501 of VC-655 board) periphery.

Note:  When the lens device was replaced, start the Adjust Manual in the Adjust Station and execute the necessary adjustment items.
 

After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the handheld operation.

Order

Procedure

1

Turn the power ON.

2

Confirm the connections of flexible flat cables and connectors between the lens device and VC-655 board.

3

In case of no malfunction of connections, replace the lens device with new one (Note) . When the error has occurred in spite of the lens 
replacement, replace VC-655 board with new one.

Note:  When the lens device was replaced, start the Adjust Manual in the Adjust Station and execute the necessary adjustment items.

After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the handheld operation.

Order

AdjustBlock

AdjustCode

Order

1

If a caution occurs only in the 2D mode, perform the procedure beginning with step 6.

2

Start the Adjust Manual in the Adjust Station and execute the [Measure to E:62:11/12 for 2D] on the 
[SERVICE] tab in the 3D mode.

3

Check if the shift lens moves while setting the order 2.
If the shift lens does not move, replace the lens device (Note).
When the shift lens moved, proceed to the order 4.

4

While setting the order 1, measure with an oscilloscope the output voltage of C5529 and C5530 in 
the periphery of IC5501 on the VC-655 board to check the output voltage varies.

5

If the output voltage does not vary, replace the lens device (Note).
When the output voltage varied, proceed to the order 6.

6

Start the Adjust Manual in the Adjust Station and execute the [Measure to E:62:11/12 for 2D] on the 
[SERVICE] tab in the 2D mode.

7

Check if the shift lens moves while setting the order 6.
If the shift lens does not move, replace the lens device (Note).
When the shift lens moved, proceed to the order 8.

8

While setting the order 1, measure with an oscilloscope the output voltage of C5525 and C5526 in 
the periphery of IC5501 on the VC-655 board to check the output voltage varies.

9

If the output voltage does not vary, replace the lens device (Note).
When the output voltage varied, proceed to the order 10.

10

Turn the power OFF.

11

While measuring with an oscilloscope the output voltage of R5506 in the periphery of IC5501 on the
VC-655 board, turn the power ON to check that the output voltage immediately after the power on
change as shown in Fig. 2.

12

If the output voltage change as shown in Fig. 2, replace the lens device (Note).
If it does not change as shown in Fig. 2, inspect the camera control circuit (IC1301 of VC-655 board
and IC5501 of VC-655 board) periphery.

Note:  When the lens device was replaced, start the Adjust Manual in the Adjust Station and execute the necessary adjustment items.
 

After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the handheld operation.