Sony HDR-FX7 / HDR-FX7E (serv.man5) Service Manual ▷ View online
6-35
HDR-FX7/FX7E_ADJ
6.
Flange Back Adjustment
RadarW
RadarW
RadarW
(Using the minipattern box or flange back adjust
ment jig)
ment jig)
The inner focus lens flange back adjustment is carried out auto-
matically. In whichever case, the focus will be deviated during
auto focusing/manual focusing.
matically. In whichever case, the focus will be deviated during
auto focusing/manual focusing.
Subject
Siemens star chart with ND filter for
minipattern box (Note 1) or flange
back adjustment jig
minipattern box (Note 1) or flange
back adjustment jig
Measurement Point
Measuring Instrument
Adjusting remote commander
Adjustment Page
6F
Adjustment Address
11, 20 to 3F, 4C, 4D
Specified value
Data of page: 6F, address: 2F is
“00” to “0E”
Data of pege: 6, address: 0C is “00”
“00” to “0E”
Data of pege: 6, address: 0C is “00”
Note 1:
Dark Siemens star chart.
Note 2:
Perform “HALL Adjustment”, “MR Adjustment” and
“Differential Gain Adjustment” before this adjustment.
“Differential Gain Adjustment” before this adjustment.
Note 3:
Perform the adjustment with the lens in horizontal state.
Note 4:
If reading/writing data on pages 6F, set data: 06 to page:
0, address: 10, and then select pages F. By this data set-
ting, the pages 6F can be selected.
After the data reading/writing finished, return the data
on page: 0, address: 10 to “00”.
0, address: 10, and then select pages F. By this data set-
ting, the pages 6F can be selected.
After the data reading/writing finished, return the data
on page: 0, address: 10 to “00”.
Note 5:
Check that the data of page: 6, address: 02 is “00”. If
not, select page: 6, address: 01, set data: 00, and press
PAUSE (Write) button.
not, select page: 6, address: 01, set data: 00, and press
PAUSE (Write) button.
Note 6:
Don't touch the zoom lever during adjustment.
Note 7:
After adjustment, if the focusing to a subject located at
infinity failed, increase the illuminance of the chart and
perform readjustment.
infinity failed, increase the illuminance of the chart and
perform readjustment.
Switch setting
1) POWER ......................................................... CAMERA mode
2) ND FILTER ...................................................................... OFF
3) REC FORMAT (Menu setting) ............................. HDV1080i
1) POWER ......................................................... CAMERA mode
2) ND FILTER ...................................................................... OFF
3) REC FORMAT (Menu setting) ............................. HDV1080i
Preparation (Using the minipattern box)
1) The minipattern box is installed as shown in the following fig-
1) The minipattern box is installed as shown in the following fig-
ure.
Note 8:
The attachment lenses are not used.
2) Install the minipattern box so that the distance between it and
the front of lens of camera is less than 3 cm.
3) Make the height of minipattern box and the camera equal.
4) Check the output voltage of the regulated power supply is the
4) Check the output voltage of the regulated power supply is the
specified voltage
± 0.01 Vdc.
5) Check that the center of Siemens star chart meets the center of
shot image screen with the zoom lens at TELE end and WIDE
end respectively.
end respectively.
Specified voltage: The specified voltage varies according to the
minipattern box, so adjustment the power sup-
ply output voltage to the specified voltage writ-
ten on the sheet which is supplied with the
minipattern box.
ply output voltage to the specified voltage writ-
ten on the sheet which is supplied with the
minipattern box.
Fig. 6-1-7
Preparation (Using the flange back adjustment jig)
(Luminance: 300 to 400 lux)
1) Install the flange back adjustment jig so that the distance be-
(Luminance: 300 to 400 lux)
1) Install the flange back adjustment jig so that the distance be-
tween it and the front of lens of camera is less than 3 cm.
2) Make the height of flange back adjustment jig and the camera
equal.
3) Check that the center of chart meets the center of shot image
screen with the zoom lens at TELE end and WIDE end respec-
tively.
tively.
Fig. 6-1-8
Minipattern box
Below 3 cm
Camera
Red (+)
Black (–)
Yellow (SENS +)
White (SENS –)
Black (GND)
Need not connected
Regulated power supply
Output voltage : Specified voltage
±
0.01 Vdc
Output current : more than 3.5 A
Flange back adjustment jig
Below 3 cm
Camera
6-36
HDR-FX7/FX7E_ADJ
Adjusting method:
Order Page Address Data
Procedure
1
0
01
01
2
6
64
04
3
0
10
0A
E
4
(AE)
8C
01
Press PAUSE (Write) button.
5
0
10
00
6
6
01
13
Press PAUSE (Write) button.
7
Wait for 2 seconds.
8
6
01
27
Press PAUSE (Write) button.
(Note 9)
(Note 9)
9
6
02
Check the data changes to “01”.
10
6
0C
Check the data is “00”.
11
0
10
06
F
12
(6F)
2F
Check the data is “00” to “0E”.
13
0
10
00
Note 9:
The adjustment data will be automatically input to page:
6F, address: 11, 20 to 3F, 4C, 4D.
6F, address: 11, 20 to 3F, 4C, 4D.
Processing after Completing Adjustment:
Order Page Address Data
Procedure
1
6
01
00
Press PAUSE (Write) button.
2
6
01
25
Press PAUSE (Write) button.
3
6
02
Check the data changes to “01”.
4
6
01
00
Press PAUSE (Write) button.
5
6
64
00
6
0
10
0A
E
7
(AE)
8C
00
Press PAUSE (Write) button.
8
0
10
00
9
0
01
00
10
Perform “Flange Back
Check”.
Check”.
6-37
HDR-FX7/FX7E_ADJ
Adjusting method:
Order Page Address Data
Procedure
1
0
01
01
2
6
64
04
3
0
10
0A
E
4
(AE)
8C
01
Press PAUSE (Write) button.
5
0
10
00
6
6
01
13
Press PAUSE (Write) button.
7
Wait for 2 seconds.
8
6
01
15
Press PAUSE (Write) button.
(Note 7)
(Note 7)
9
6
02
Check the data changes to
“01”.
“01”.
10
6
0C
Check the data is “00”.
11
0
10
06
12
F
2F
Check the data is “00” to
(6F)
“0E”.
13
0
10
00
Note 7:
The adjustment data will be automatically input to page:
6F, address: 11, 20 to 3F, 4C, 4D.
6F, address: 11, 20 to 3F, 4C, 4D.
Processing after Completing Adjustment:
Order Page Address Data
Procedure
1
6
01
00
Press PAUSE (Write) button.
2
6
01
25
Press PAUSE (Write) button.
3
6
02
Check the data changes to “01”.
4
6
01
00
Press PAUSE (Write) button.
5
6
64
00
6
0
10
0A
E
7
(AE)
8C
00
Press PAUSE (Write) button.
8
0
10
00
9
0
01
00
10
Perform “Flange Back
Adjustment (2)”.
Adjustment (2)”.
7.
Flange Back Adjustment
(Using the flange back adjustment chart and
subject more than 500 m away)
(Using the flange back adjustment chart and
subject more than 500 m away)
The inner focus lens flange back adjustment is carried out auto-
matically. In whichever case, the focus will be deviated during
auto focusing/manual focusing.
matically. In whichever case, the focus will be deviated during
auto focusing/manual focusing.
7-1. Flange Back Adjustment (1)
RadarW
RadarW
RadarW
RadarW
RadarW
Subject
Flange back adjustment chart
(2.0 m from the front of lens)
(Luminance: 300 to 400 lux)
(2.0 m from the front of lens)
(Luminance: 300 to 400 lux)
Measurement Point
Adjusting remote commander
Measuring Instrument
Adjustment Page
6F
Adjustment Address
11, 20 to 3F, 4C, 4D
Specified value
Data of page: 6F, address: 2F is
“00” to “0E”
Data of page: 6, address: 0C is “00”
“00” to “0E”
Data of page: 6, address: 0C is “00”
Note 1:
Perform “HALL Adjustment”, “MR Adjustment” and
“Differential Gain Adjustment” before this adjustment.
“Differential Gain Adjustment” before this adjustment.
Note 2:
Perform the adjustment with the lens in horizontal state.
Note 3:
If reading/writing data on pages 6F, set data: 06 to page:
0, address: 10, and then select pages F. By this data set-
ting, the pages 6F can be selected.
After the data reading/writing finished, return the data
on page: 0, address: 10 to “00”.
0, address: 10, and then select pages F. By this data set-
ting, the pages 6F can be selected.
After the data reading/writing finished, return the data
on page: 0, address: 10 to “00”.
Note 4:
Check that the data of page: 6, address: 02 is “00”. If
not, select page: 6, address: 01, set data: 00, and press
PAUSE (Write) button.
not, select page: 6, address: 01, set data: 00, and press
PAUSE (Write) button.
Note 5:
Don't touch the zoom lever during adjustment.
Note 6:
After adjustment, if the focusing to a subject located at
infinity failed, increase the illuminance of the chart and
perform readjustment.
infinity failed, increase the illuminance of the chart and
perform readjustment.
Switch setting
1) POWER ......................................................... CAMERA mode
2) ND FILTER ...................................................................... OFF
3) REC FORMAT (Menu setting) ............................. HDV1080i
1) POWER ......................................................... CAMERA mode
2) ND FILTER ...................................................................... OFF
3) REC FORMAT (Menu setting) ............................. HDV1080i
Preparations before adjustments:
1) Check that the center of Flange back adjustment chart meets
1) Check that the center of Flange back adjustment chart meets
the center of shot image screen with the zoom lens at TELE
end and WIDE end respectively.
end and WIDE end respectively.
6-38
HDR-FX7/FX7E_ADJ
7-2. Flange Back Adjustment (2)
RadarW
RadarW
RadarW
Perform this adjustment after performing “Flange Back Adjust-
ment (1)”.
ment (1)”.
Subject
Subject more than 500 m away
(Subject with clear contrast such as
buildings, etc.)
(Subject with clear contrast such as
buildings, etc.)
Measurement Point
Adjusting remote commander
Measuring Instrument
Adjustment Page
6F
Adjustment Address
11, 20 to 3F, 4C, 4D
Specified value
Data of page: 6F, address: 2F is
“00” to “0E”
Data of page: 6, address: 0C is“00”
“00” to “0E”
Data of page: 6, address: 0C is“00”
Note 1:
Perform the adjustment with the lens in horizontal state.
Note 2:
If reading/writing data on pages 6F, set data: 06 to page:
0, address: 10, and then select pages F. By this data set-
ting, the pages 6F can be selected.
After the data reading/writing finished, return the data
on page: 0, address: 10 to “00”.
0, address: 10, and then select pages F. By this data set-
ting, the pages 6F can be selected.
After the data reading/writing finished, return the data
on page: 0, address: 10 to “00”.
Note 3:
Check that the data of page: 6, address: 02 is “00”. If
not, select page: 6, address: 01, set data: 00, and press
PAUSE (Write) button.
not, select page: 6, address: 01, set data: 00, and press
PAUSE (Write) button.
Note 4:
Don’t touch the zoom lever during adjustment.
Switch setting
1) POWER ......................................................... CAMERA mode
2) ND FILTER ...................................................................... OFF
3) REC FORMAT (Menu setting) ............................. HDV1080i
1) POWER ......................................................... CAMERA mode
2) ND FILTER ...................................................................... OFF
3) REC FORMAT (Menu setting) ............................. HDV1080i
Preparations before adjustments:
1) Set the zoom lens to the TELE end and expose a subject that is
1) Set the zoom lens to the TELE end and expose a subject that is
more than 500 m away.
(subjects with clear contrast such as building, etc.)
(Nearby subjects less than 500 m away should not be in the
screen)
(subjects with clear contrast such as building, etc.)
(Nearby subjects less than 500 m away should not be in the
screen)
Adjusting method:
Order Page Address Data
Procedure
1
0
01
01
2
6
64
04
3
0
10
0A
E
4
(AE)
8C
01
Press PAUSE (Write) button.
5
0
10
00
6
6
01
13
Press PAUSE (Write) button.
7
Wait for 2 seconds.
8
Place ND filter on the lens so
that the optimum image is
obtain.
that the optimum image is
obtain.
9
6
01
29
Press PAUSE (Write) button.
(Note 5)
(Note 5)
10
6
02
Check the data changes to “01”.
11
6
0C
Check the data is “00”.
12
0
10
06
13
F
2F
Check the data is “00” to “0E”.
(6F)
14
0
10
00
Note 5:
The adjustment data will be automatically input to page:
6F, address: 11, 20 to 3F, 4C, 4D.
6F, address: 11, 20 to 3F, 4C, 4D.
Processing after Completing Adjustment:
Order Page Address Data
Procedure
1
6
01
00
Press PAUSE (Write) button.
2
6
01
25
Press PAUSE (Write) button.
3
6
02
Check the data changes to “01”.
4
6
01
00
Press PAUSE (Write) button.
5
6
64
00
6
0
10
0A
E
7
(AE)
8C
00
Press PAUSE (Write) button.
8
0
10
00
9
0
01
00
10
Perform “Flange Back
Check”.
Check”.
Click on the first or last page to see other HDR-FX7 / HDR-FX7E (serv.man5) service manuals if exist.