DOWNLOAD Sony HDR-FX1 / HDR-FX1E (serv.man3) Service Manual ↓ Size: 2.45 MB | Pages: 86 in PDF or view online for FREE

6-66

HDR-FX1/FX1E

Mode

CAMERA

Subject

Arbitrary

Measurement Point

Video plug of AUDIO/VIDEO jack
(75

Ω

 terminated)

Measuring Instrument

Oscilloscope

Specified Value

Sync level: A = 286 

±

 18mV (NTSC)

A = 300 

±

 18mV (PAL)

Burst level: B = 286 

±

 18mV (NTSC)

B = 300 

±

 18mV (PAL)

Note1: Disconnect the cable from the COMPONENT OUTPUT

connector.

Note2: The data of page: 0, address: 10 must be “00”.

1

0

01

01

Set the data.

2

3

0C

02

Set the data, and press PAUSE
button.

3

Wait for 5 sec.

4

3

11

Check that bit5 of the data is
“1”. (Note3)

5

Check that the sync signal level
(A) satisfies the specified value.

6

Check that the burst signal level
(B) satisfies the specified value.

7

3

0C

00

Set the data, and press PAUSE
button.

8

0

01

00

Set the data.

Note3: For the bit values, refer to “6-4. SERVICE MODE”, “4-3. 3. Bit

value discrimination”.

Fig. 6-3-6.

H

B

A

6-67

HDR-FX1/FX1E

Mode

CAMERA

Subject

Arbitrary

Measurement Point

Y signal: Y signal terminal of
COMPONENT OUTPUT connector
(75

Ω

 terminated)

PR signal: PR signal terminal of
COMPONENT OUTPUT connector
(75

Ω

 terminated)

PB signal: PB signal terminal of
COMPONENT OUTPUT connector
(75

Ω

 terminated)

Measuring Instrument

Oscilloscope

Adjustment Page

C

Adjustment Address

82, 83, 84

Specified Value

Y level:

A = 1000 

±

 10mV

PR level:

B = 525 

±

 10mV

PB level:

C = 525 

±

 10mV

SYNC level: D = E = 300 

±

 10mV

Note: When the component video signals are not outputted, connect the

SW terminal (Pin q;) of the COMPONENT OUTPUT connector to
GND.

Switch setting:
REC FORMAT (IN/OUT REC menu) ......................... HDV1080i
DISP OUTPUT (OTHERS menu) ............................ LCD PANEL

1

0

01

01

Set the data.

2

0

10

01

Set the data.

3

8

01

04

Set the data, and press PAUSE button.

4

0

10

00

Set the data.

5

Connect the oscilloscope to the
Y signal terminal.

6

C

82

Change the data and set the Y
level (A) to the specified value.

7

C

82

Press PAUSE button.

8

Check that the SYNC level (D)
and SYNC level (E) are satisfied
the specified value.

9

Connect the oscilloscope to the
PR signal terminal.

10

C

83

Change the data and set the PR
level (B) to the specified value.

11

C

83

Press PAUSE button.

12

Check that the SYNC level (D)
and SYNC level (E) are satisfied
the specified value.

13

Connect the oscilloscope to the
PB signal terminal.

14

C

84

Change the data and set the PB
level (C) to the specified value.

15

C

84

Press PAUSE button.

16

Check that the SYNC level (D)
and SYNC level (E) are satisfied
the specified value.

17

0

10

01

Set the data.

18

8

01

00

Set the data, and press PAUSE button.

19

0

10

00

Set the data.

20

0

01

00

Set the data.

Fig. 6-3-7.

Fig. 6-3-8.

Fig. 6-3-9.

H

A

D

E

H

B

D

E

H

C

D

E

6-68

HDR-FX1/FX1E

[Connection of Audio System Measuring Devices]
Connect the audio system measuring devices as shown in Fig. 6-3-10.

Fig. 6-3-10.

Ω

Ω

Ω

Ω

Ω

Ω

Ω

Ω

Ω

Ω

Ω

Ω

Ω

Ω

6-69

HDR-FX1/FX1E

Mode

Playback

Signal

Alignment tape:

For audio operation check
(XH5-3 (NTSC))
(XH5-3P (PAL))

Measurement Point

Audio left or right terminal of
AUDIO/VIDEO jack

Measuring Instrument

Audio level meter and frequency
counter

Specified Value

32 kHz mode: 1 kHz, +8.2 

±

 2.0dBs

48 kHz mode: 1 kHz, +8.2 

±

 2.0dBs

44.1 kHz mode:
The 7.35kHz signal level during EMP
OFF is +8.2 

±

 2.0dBs.

The 7.35kHz signal level during EMP
ON is 0 

±

 2.2dBs.

Checking Method:
1)

Check that the playback signal level is the specified value.

Mode

Camera recording and playback

Signal

1kHz, -6.0dBs signal:
Left and right terminal of MIC/LINE
jack

Measurement Point

Audio left or right terminal of
AUDIO/VIDEO jack

Measuring Instrument

Audio level meter

Specified Value

-4.0 

±

 2.0dBs

Switch setting:
MIC/LINE( AUDIO SET menu) ........................................... LINE
AUDIO SELECT .......................................................... MANUAL

Checking Method:
1)

Input the 1kHz, -6.0dBs signal in the left and right terminal of
MIC/LINE jack

2)

Push STATUS CHECK button and display level meters.

3)

Turn AUDIO LEVEL knob from “0” position, little by little,
until the level meter which shows smoller level displays
“–12dB”.

4)

Record the signal.

5)

Playback the recorded section.

6)

Check that the 1kHz signal level is the specified value.

Mode

Camera E-E

Signal

70Hz, -60dBs signal:
1kHz, -62dBs signal:
Left and right terminal of MIC/LINE
jack

Measurement Point

Audio left or right terminal of
AUDIO/VIDEO jack

Measuring Instrument

Audio level meter, digital volt meter

Specified Value

-4.0 

±

 2.0dBs

Switch setting:
MIC/LINE( AUDIO SET menu) ............................................ MIC
WIND (AUDIO SET menu) .................................................... OFF
AUDIO SELECT .......................................................... MANUAL
AUDIO LEVEL .......................... Position set by “2. Overall Level

Characteristics Check”

Checking Method:
1)

Check that the DC voltage of the left and right terminal of
MIC/LINE jack is 2Vdc to 3Vdc. (Do not connect the audio
oscillator and attenuator.)

2)

Input the 1kHz, -62dBs signal in the left and right terminal of
MIC/LINE jack

3)

Check that the 1kHz signal level is the specified value.

4)

Input the 70Hz, -60dBs signal in the left and right terminal of
MIC/LINE jack

5)

Check that the 70Hz signal level is the specified value.

6)

Set WIND menu (AUDIO SET menu) to “ON”.

7)

Check that the 70Hz signal level is -6dB from the signal level
during WIND OFF.

8)

Set WIND menu to “OFF”.

Mode

Camera E-E

Signal

70Hz, -6dBs signal:
1kHz, -6dBs signal:
20kHz, -6dBs signal:
Left and right terminal of MIC/LINE
jack

Measurement Point

Audio left or right terminal of
AUDIO/VIDEO jack

Measuring Instrument

Audio level meter, digital volt meter

Specified Value

-4.0 

±

 2.0dBs

Switch setting:
MIC/LINE( AUDIO SET menu) ........................................... LINE
AUDIO SELECT .......................................................... MANUAL
AUDIO LEVEL .......................... Position set by “2. Overall Level

Characteristics Check”

Checking Method:
1)

Check that the DC voltage of the left and right terminal of
MIC/LINE jack is 0Vdc. (Do not connect the audio oscillator
and attenuator.)

2)

Input the 70Hz, -6dBs signal in the left and right terminal of
MIC/LINE jack

3)

Check that the 70Hz signal level is the specified value.

4)

Input the 1kHz, -6dBs signal in the left and right terminal of
MIC/LINE jack

5)

Check that the 1kHz signal level is the specified value.

6)

Input the 20kHz, -6dBs signal in the left and right terminal of
MIC/LINE jack

7)

Check that the 20kHz signal level is the specified value.