DOWNLOAD Sony HDR-CX190 / HDR-CX190E / HDR-CX200 / HDR-CX200E / HDR-CX210 / HDR-CX210E / HDR-PJ200 / HDR-PJ200E / HDR-PJ210 (serv.man2) Service Manual ↓ Size: 4.14 MB | Pages: 27 in PDF or view online for FREE

HDR-CX190/CX190E/CX200/CX200E/CX210/CX210E/PJ200/PJ200E/PJ210_L2

1-1

In this unit, about 10 seconds after power is supplied to the battery terminal using the regulated power supply (8.4 V), the power is shut off 
so that the unit cannot operate.
These following method is available to prevent this.

Use the AC power adaptor.

Note the following when replacing the board.

Note:  When replacing the board, it is necessary to change the destination data first. 
 

To change the destination data, execute the [DESTINATION DATA WRITE] of ADJUST tab in the Adjust Manual.

When you replace to the repairing board, the written destination data of repairing board also might be changed to original setting.
Start the Adjust Manual in the Adjust Station and execute the “DESTINATON DATA WRITE”.
After the board replacement, the error of the built-in recording media may be displayed. In this case, execute the [DESTINATION DATA WRITE]
then the error will be cleared. If it is not cleared with [DESTINATION DATA WRITE], format the built-in recording media.

When you replace to the repairing board, get the data from the former one.
Start the Adjust Manual in the Adjust Station and perform “USB SERIAL SAVE” to get the data.

The set is shipped with a unique ID (USB Serial No.) written in it.
This ID has not been written in a new board for service, and therefore it must be entered after the board replacement.
Start the Adjust Manual in the Adjust Station and execute the “USB SERIAL No. INPUT”.

Before replacing the board with a spare board, acquire the following data from the current board.
•  Fixed value (that shows irradiation performance of the projector).
•  Serial number of the projector unit.
To acquire the data, start Adjust Manual from Adjust Station and select [Projector Data Reference] on the [DATA] tab.

After the board replacement, execute the procedure below first.
1.  Execute the [DESTINATION DATA WRITE] of ADJUST tab in the Adjust Manual.
2.  Execute the script files below. (Refer to the flowchart in Fig. 1)

• 11DdmMmcReadTestMINI_v4.vbe
• 11DdmMmcMakePartition_v4.vbe

Note:  Download the script files from TISS Homepage.
 

When searching in the TISS Homepage, enter “IM_VC_TOOL” for keyword in the Part Number field.

Unless these script files are executed, the following symptoms may appear.
Make sure execute the above script files.
•  The internal memory is not recognized as a media.
•  The management file saved in the internal memory model cannot be repaired.
•  The internal memory cannot be formatted.

START

END

Reactive the camcorder automatically

Disconnect the USB cable,

 and turnoff the power switch.

Select the "USB CONNECT" to establish 

the connection

Execute 

the "DdmMmcReadTestMINI.vbe"

(several second)

Wait until "SetOverallReadMINI OK" display

Reactive the camcorder automatically

Execute

 the "11DdmMMCMakePartition.vbe"

(several second)

Wait until "MakePartition OK" display

During the power is turning-on,

 pull-out the AC-adapter. 

Then connect the AC-adapter Again 

(It's running with blue color monitor.)

Connect to the PC with a USB cable, 

and turn on the power switch.

* by SEUS driver

HDR-CX190/CX190E/CX200/CX200E/CX210/CX210E/PJ200/PJ200E/PJ210_L2

1-2

If the Destination Data file included in the Adjust manual is old, “DESTINATION DATA WRITE” cannot be executed in some cases.
In that case, download a new Destination Data file from the TISS homepage according to the following procedure.

Note 1:  To perform Destination Data Write for this model, the Adjust manual of the DSC-WX50 series must have been installed.
 

Install the Adjust manual of the DSC-WX50 series in advance.

Note 2:  The actual image may differ from the image shown above.

1)  If the Destination Data file in the Adjust manual in use is old, the window shown in Fig. 1 is displayed.
 

Click the [OK] button.

2)  The Destination Data Write window opens.
 

Check the version of the Destination Data file retained in the Adjust manual.

Destination Ver. window

3)  Search the model whose new Destination Data file you want to get on the TISS homepage.
 

When the Destination Data file has been updated, a file with a name “Destination File For ‘model name’.zip” is registered.

(Example) Destination File For DSC-WX50.zip

Furthermore, the version supported by the Destination Data file is shown in the Remarks column.

Note : If the Destination Data file has not been updated, contact the Service Headquarters.

 4)  Download the Destination Data file of the relevant model and unzip the file.

5)  Execute “DESTINATION DATA WRITE” in the Adjust tab of the Adjust manual.
 

Click the [START] button.

HDR-CX190/CX190E/CX200/CX200E/CX210/CX210E/PJ200/PJ200E/PJ210_L2

1-3

6)  Click the [File Update] button in the window.
 

7)  A file selection screen opens. Select the Destination Data file to be added and click the [Open] button.
 

8)  When the file has been successfully added, the following window opens.
 

9)  Check the Destination Ver. window and confirm that the version has been updated.

Destination Ver. window

The changed portions from
Ver. 1.0 are shown in blue.

When problems occur while the unit is operating, the self-diagnosis 
function starts working, and displays on the LCD screen what to do.
This function consists of two display; self-diagnosis display and service 
mode display.Details of the self-diagnosis functions are provided in the 
Instruction manual.

When problems occur while the unit is operating, the counter of the LCD 
screen shows a 4-digit display consisting of an alphabet and numbers,
which blinks at 3.2 Hz. This 5-character display indicates the “repaired 
by:”, “block” in which the problem occurred, and “detailed code”of the 
problem.

0 0

3 2

C

Repaired by:

Refer to “1-4-3. Self-diagnosis Code Tabl e”.

Indicates the appropriate
step to be taken.
E.g.
13 ....
32 ....Turn on power again.

Block

Detailed Code

Blinks at 3.2 Hz

C : Corrected by customer
E : Corrected by service

engineer

Format the “memory card”.

LCD screen

Self-diagnosis Code

Symptom/State

Correction

Repaired by:

Block

Function

Detailed

Code

C

0

4

0

0

Non-standard battery is used.

Use the InfoLITHIUM battery.

C

0

6

0

0

The battery pack temperature is high.

Change the battery pack or place it in a cool place.

C

1

3

0

1 

Memory card is unformatted.
Memory card is broken.

Format the memory card.
Insert a new memory card.

C

1

3

0

2

Access error

Remove the power source. Reconnect it again and operate your cam-
corder again.

C

1

3

0

3

Access error (External mdedia)

Turn power off and turn power on again.

C

1

3

0

4

Drive fault (External mdedia)

Turn power off and turn power on again.

C

E

3

2

6

1

6

0

0

0

Difficult to adjust focus
(Cannot initialize focus)

Retry turn the power on by the power switch. If it does not recover, 
check the focus drive signal of lens block (pin wa to wf of CN1005 on 
the VC-651 board). If it is OK, check the focus motor drive IC (IC5306 
on the VC-651 board).

E

2

0

0

0

Flash memory data are rewritten.

Make flash memory data correct value. (Note 1)

E

3

1

0

0

Drive fault

Turn power off and turn power on again.

Note 1: Start the Adjust Manual in the Adjust Station and refer to the “DESTINATON DATA WRITE”.
Note 2: Functions of codes with * mark are not provided in this unit.

*

*

*

(                                           )

*

HDR-CX190/CX190E/CX200/CX200E/CX210/CX210E/PJ200/PJ200E/PJ210_L2

1-4

Self-diagnosis Code

Symptom/State

Correction

Repaired by:

Block

Function

Detailed

Code

E

6

1

1

0

Zoom operations fault
(Cannot initialize zoom lens.)

Inspect the lens block zoom drive signal (pin 1 to 4 of CN1005 on 
the VC-651 board, when zooming is performed when the zoom lever is 
operated, and the zoom motor drive IC (IC5306 on the VC-651 board) 
when zooming is not performed.

E

6

1

1

1

The abnormalities in initialization of the focus 
lens and the abnormalities in initialization of 
the zoom lens occurred simultaneously.

Check both C: 32: 60 and E: 61: 10 of the self-diagnosis code.

E

6

1

3

0

Reset position detection error on the stepper 
iris initializing

Turn the power on to open lens barrier. Disconnect the battery or power 
cord, and then connect again.
Confirm that the iris blades in lens are working.
If iris blades do not working, check the iris motor drive IC in lens drive 
block (CN1005 pin qd to qk on the VC-651 board).
If iris blades work normally, confirm that they are closing completely 
and confirm following item.
･  Case of the iris blades do not close normally Replace the lens block).
･  Case of “E: 61: 30” is appeared and iris blades closed completely.
  Confirm that communication with lens block is normal.
･ Case of LCD is not displayed normally Check that connection 

between CN6805 on the CM-127 board and CN1002 and VC-651 
board by FP-1483 flexible board.

･  Case of LCD is displayed normally Replace the lens block.

E

6

2

0

0

Handshake correction function does not work 
well. (With PITCH angular velocity sensor 
output stopped.)

Inspect PITCH angular velocity sensors (SE7501 on the CM-127 
board) peripheral circuits.

E

6

2

0

1

Handshake correction function does not work 
well. (With YAW angular velocity sensor 
output stopped.)

Inspect YAW angular velocity sensors (SE7501 on the CM-127 board) 
peripheral circuits.

E

6

2

0

2

Abnormality of IC for steadyshot.

Turn power off and turn power on again.

E

6

2

0

3

IC for steadyshot and micro controller com-
munication abnormality among.

Turn power off and turn power on again.

E

6

2

0

4

Image vibration correction during handshake 
function does not work.

Inspect the image vibration angular velocity sensors (SE7501 in the 
CM-127 board) peripheral circuits.

E

6

2

1

0

Shift lens initializing failure.

Replacement of lens block. (Note 3) 
If an error occurs again, replace the VC-651 board.

E

6

2

1

1

Shift lens overheating (Pitch)

Turn power off and turn power on again.

E

6

2

1

2

Shift lens overheating (Yaw)

Turn power off and turn power on again.

E

6

2

2

0

Abnormality of thermistor.

Turn power off and turn power on again.

E

9

1

0

1

Abnormality when flash is beingcharged.

Turn power off and turn power on again.

E

9

1

0

2

Abnormality of LED Video light.

Turn power off and turn power on again.

E

9

1

0

3

Abnormality of LED Video light  Tempera-
ture detection.

Turn power off and turn power on again.

E

9

2

0

1

Battery current value goes over the max 
discharge current

Check the remaining battery power because this symptom maybe 
depended on the remaining battery level, and confirm whether or 
not the symptom is occurred after replacing the battery. If the symp-
tom is still occurred, overhaul inspection is needed. Check each 
output of DC/DC converter (IC4301 on the VC-651 board) on with 
connected the DC JACK (J1001). 
(The minimum connection to periphery)

E

9

4

0

0

Fault of writing or erasing the flash mem-
ory

IM Model:
Inspect the flash memory (IC8101, IC8201 on the MM-102 board).

E

9

4

0

1

Internal flash memory fault

IM Model:
Inspect the flash memory (IC8101, IC8201 on the MM-102 board).

E

9

4

0

2

BGM data error

Check the CPU (IC1301 on the VC-651 board).

*

*

*

*

*

Self-diagnosis Code

Symptom/State

Correction

Repaired by:

Block

Function

Detailed

Code

E

9

5

0

0

GPS hardware error

Turn power off and turn power on again.

E

9

6

0

0

Map area mount error

Turn power off and turn power on again.

E

9

7

0

0

Projector  hardware error

Turn power off and turn power on again.

Note 3: When the lens block was replaced, start the Adjust Manual in the Adjust Station and execute the necessary adjustment items.

After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the handheld operation.

Refer to the following flowchart when repairing or inspecting the projector’s projection function.

If you have received an indication on the projector’s projection function from the customer, check defective part according to the following flow-
chart. 
When a defective part has been clarified, repair the projector according to the check result.

Note 1: The projector unit (copper plate in particular) becomes hot after it is used.
 

When replacing a part of the projector unit, wait until it is cooled down.

 

Wipe the lens gently with a soft cloth such as a cleaning cloth or glass cleaning cloth.

Note 2: Stubborn stains may be removed with a soft cloth such as a cleaning cloth or glass cleaning cloth lightly dampened with water.
 

Never use a solvent such as alcohol, benzene or thinner; acid, alkaline or abrasive detergent; or a chemical cleaning cloth, as they will damage the lens sur-
face.

*

*

Indicated defective

projector received

Measure brightness.

(  2)

Yes

No

OK

OK

NG

NG

OK

NG

A

B

Indication on 

brightness

Inspect projector

LED. 

(  1)

  1  Refer to the ADJUST tab of Adjust Manual.
  2  Refer to the SERVICE tab of Adjust Manual.

Inspect projector

LED. 

(  1)

END

-
-
-

-

-

Replace projector unit (light emitting block). (*1)
Replace PJ board. (*1)
Replace both projector unit (light emitting block)
and PJ board. (*1)

Projector Data Input

Fixed value input
Enter the number on the label attached to the unit.

Serial number input
LD40

Syywwnnnnn 

Enter the red part.

(See page 1-5)

(See page 1-5)

The changed portions from
Ver. 1.0 are shown in blue.