Sony HDR-CX11E / HDR-CX12 / HDR-CX12E (serv.man2) Service Manual ▷ View online
1-14
HDR-CX11E/CX12/CX12E_L2
(ENGLISH)
1-6. PRECAUTION ON REPLACING
1-6. PRECAUTION ON REPLACING
THE HOLDER (MS)
(HDR-CX12)
(HDR-CX12)
The model display adopts the laser printing method.Therefore, the
holder (MS) for replacement differs depending on the destination.
As similar displays are provided, choose the suitable one for order.
holder (MS) for replacement differs depending on the destination.
As similar displays are provided, choose the suitable one for order.
Note1: After replacing the holder (MS), the serial number for it
will be changed to the one exclusive for service use.
Inform a customer of the serial number change and change the serial
number in the repair data.
will be changed to the one exclusive for service use.
Inform a customer of the serial number change and change the serial
number in the repair data.
Note 2: When replacing the holder (MS) for US, affix the
“Manufacturing year” label and the “Factory” label on the specified
location as shown in the figure.
The replacement caution label and inset (how to affix) are supplied
together with the holder (MS).
“Manufacturing year” label and the “Factory” label on the specified
location as shown in the figure.
The replacement caution label and inset (how to affix) are supplied
together with the holder (MS).
Note 3: When replacing the holder (MS) for Korea and Japanese,
affix the “Manufacturing year” label on the specified location as
shown in the figure.
The replacement caution label and inset (how to affix) are supplied
together with the holder (MS).
affix the “Manufacturing year” label on the specified location as
shown in the figure.
The replacement caution label and inset (how to affix) are supplied
together with the holder (MS).
(JAPANESE)
1-6.
1-6.
ホルダー (MS)交換時の注意
(HDR-CX12)
(HDR-CX12)
機種の表示部はレーザー印字方式を採用しております。
この為，交換用のホルダー ( M S ) は仕向けにより異なりま
す。類似の表示もありますので，該当するものを選んで注
文して下さい。
注意1: ホルダー (MS)交換後はシリアルナンバーがサービ
ス専用のシリアルナンバーに変更されます。お客様への案
内と修理データのシリアルナンバー変更を行ってくださ
い。
注意2: US仕向けホルダー (MS)を交換した際は「製造年
月」を表すラベルと，「製造所」を表すラベルを図の指定
位置に貼り付けてください。
なお，ホルダー (MS)には時期表示ラベル，投げ込み(ラベ
ル貼り方)がセットで供給されます。
注意3: Korean仕向け，Japanese仕向けホルダー (MS)を
交換した際は，「製造年月」を表すラベルを図の指定位置
に貼り付けてください。
なお，ホルダー (MS)には時期表示ラベル，投げ込み(ラベ
ル貼り方)がセットで供給されます。
Serial No.
Serial No.
Serial No.
Serial No.
Serial No.
Serial No.
*
Manufacturing year
*
Manufacturing year
*
Manufacturing year
*
Factory
HDR-CX12 (Japanese Model)
Part No.
A-1556-656-A
Description
HOLDER (CX12-J1), (MS)
HDR-CX12 (US Model)
Part No.
A-1556-658-A
Description
HOLDER (CX12-U2), (MS)
*
Affix the label
*
Affix the label
*
Affix the label
HDR-CX12 (Canadian Model)
Part No.
A-1556-659-A
HOLDER (CX12-CA2),(MS)
HDR-CX12 (E Model)
Part No.
A-1556-660-A
Description
Description
HOLDER (CX12-E23),(MS)
HDR-CX12 (Korea Model)
Part No.
A-1556-661-A
Description
HOLDER (CX12-KR2),(MS)
HDR-CX12 (Tourist Model)
Part No.
A-1556-662-A
Description
HOLDER (CX12-JE3),(MS)
1-15E
HDR-CX11E/CX12/CX12E_L2
(ENGLISH)
1-7. PRECAUTION ON REPLACING
1-7. PRECAUTION ON REPLACING
THE HOLDER (MS)
(HDR-CX12E)
(HDR-CX12E)
The model display adopts the laser printing method.Therefore, the
holder (MS) for replacement differs depending on the destination.
As similar displays are provided, choose the suitable one for order.
holder (MS) for replacement differs depending on the destination.
As similar displays are provided, choose the suitable one for order.
Note1: After replacing the holder (MS) , the serial number for it
will be changed to the one exclusive for service use.
Inform a customer of the serial number change and change the serial
number in the repair data.
will be changed to the one exclusive for service use.
Inform a customer of the serial number change and change the serial
number in the repair data.
(JAPANESE)
1-7.
1-7.
ホルダー (MS)交換時の注意
(HDR-CX12E)
機種の表示部はレーザー印字方式を採用しております。
この為，交換用のホルダー ( M S ) は仕向けにより異なりま
す。類似の表示もありますので，該当するものを選んで注
文して下さい。
注意1: ホルダー (MS)交換後はシリアルナンバーがサービ
ス専用のシリアルナンバーに変更されます。お客様への案
内と修理データのシリアルナンバー変更を行ってくださ
い。
Serial No.
Serial No.
Serial No.
Serial No.
HDR-CX12E (North European Model)
Part No.
A-1556-667-A
Description
HOLDER (CX12E-CEL),(MS)
HDR-CX12E (E, Hong Kong, Australian Models)
Part No.
A-1556-663-A
Description
HOLDER (CX12E-E34),(MS)
HDR-CX12E (Chinese Model)
Part No.
A-1556-664-A
HOLDER (CX12E-CN2),(MS)
HDR-CX12E (Tourist Model)
Part No.
A-1556-666-A
Description
Description
HOLDER (CX12E-JE3),(MS)
2-1
2. DISASSEMBLY
HDR-CX11E/CX12/CX12E_L2
NOTE FOR REPAIR
• Make sure that the flat cable and flexible board are not cracked of bent at the terminal.
Do not insert the cable insufficiently nor crookedly.
• When remove a connector, don’t pull at wire of connector. It is possible that a wire is snapped.
• When installing a connector, don’t press down at wire of connector.
It is possible that a wire is snapped.
Cut and remove the part of gilt
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
DISCHARGING OF THE ST-201 BOARD’S CHARGING CAPACITOR (C5206)
The charging capacitor (C5206) of the ST-201 board is charged
up to the maximum 330 V potential.
There is a danger of electric shock by this high voltage when the
capacitor is handled by hand. The electric shock is caused by
the charged voltage which is kept without discharging when the
main power of the unit is simply turned off. Therefore, the
remaining voltage must be discharged as described below.
up to the maximum 330 V potential.
There is a danger of electric shock by this high voltage when the
capacitor is handled by hand. The electric shock is caused by
the charged voltage which is kept without discharging when the
main power of the unit is simply turned off. Therefore, the
remaining voltage must be discharged as described below.
Preparing the Short Jig
To preparing the short jig, a small clip is attached to each end of
a resistor of 1 k
a resistor of 1 k
Ω /1 W (1-215-869-11).
Wrap insulating tape fully around the leads of the resistor to
prevent electrical shock.
prevent electrical shock.
Harness
(coaxial cable)
(coaxial cable)
Tweezers etc.
1 k
Ω
/1 W
Wrap insulating tape.
NOTE FOR DISCONNECTING THE HARNESS (COAXIAL CABLE)
When disconnecting the harness (COAXIAL CABLE), do not
pull the harness part but pull off the connector body with tweezers
etc.
pull the harness part but pull off the connector body with tweezers
etc.
ST-201 Board
ST-201 Board
Elect Cap
70uF 330V
(C5206)
70uF 330V
(C5206)
Note: High-voltage cautions
Discharging the Capacitor
Short-circuit between the two points with
the short jig about 10 seconds.
To avoid the spark with the metal plate,
wrap the short jig with the insulation tape.
Short-circuit between the two points with
the short jig about 10 seconds.
To avoid the spark with the metal plate,
wrap the short jig with the insulation tape.
R:1 k
Ω
/1 W
(Part code: 1-215-869-11)
2-2
HDR-CX11E/CX12/CX12E_L2
2-1. IDENTIFYING PARTS
2-2-1. OVERALL SECTION
- LCD Panel Section
- Front Panel Section
- Front Panel Section
2-2-4. MAIN BODY SECTION
- Top Cabinet Section
- MS-402 Board Section
- Cabinet L Section
- MS-402 Board Section
- Cabinet L Section
2-2-5. LENS/BT SECTION
- VC-535 Board Block
- BT Panel Section
- ST-201 Board Block
- BT Panel Section
- ST-201 Board Block
2-2-2. LCD PANEL SECTION
- LCD Panel Section
2-2-3. CABINET R SECTION
- Hinge Block
- CK-203 Board
- Loud Speaker (SP901)
- CK-203 Board
- Loud Speaker (SP901)
- DISASSEMBLY FLOW -
Lens Section
⋅
LD-241 Board
⋅
CM-094 Board
Top Cabinet Section
⋅
PH-003 Board
BT Panel Section
⋅
CR-092 Board
Cabinet R Section
⋅
CK-203 Board
VC-535 Board
Cabinet L Section
LCD Panel Section
⋅
PD-371 Board
MS-402 Board Section
⋅
MS-402 Board
Flash Unit Section
⋅
ST-201 Board
Front Panel Section
Click on the first or last page to see other HDR-CX11E / HDR-CX12 / HDR-CX12E (serv.man2) service manuals if exist.