Sony FDR-AX30 / FDR-AX33 / FDR-AXP33 / FDR-AXP35 Service Manual ▷ View online
2-5.
Checking the Wi-Fi Function
After this unit has been disassembled and reassembled, check the Wi-Fi function.
Required equipment:
Windows PC or smartphone with Wi-Fi interface
Procedure:
1.
Turn on the power of the unit and enable the Wi-Fi function.
(Upon completion of the preparation for Wi-Fi connection, the password for Wi-Fi connection is displayed.)
(Upon completion of the preparation for Wi-Fi connection, the password for Wi-Fi connection is displayed.)
2.
Confirm on the PC or the smartphone that the unit is detected as a connectable wireless network.
FDR-AX30/FDR-AX33/FDR-AXP33/FDR-AXP35
2-9
2-6.
Precaution on Replacing the LD-1017 Board
2-6-1.
Angular Velocity Sensor
Before replacing the board with a repairing board, be sure to record the sensitivity indicated on the angular velocity
sensor on the repairing board.
The recorded sensitivity indication must be stored in the repairing board.
sensor on the repairing board.
The recorded sensitivity indication must be stored in the repairing board.
Method of the angular velocity sensor sensitivity writing:
Start the Adjust Manual in the Adjust Station and execute the “Angular velocity sensor sensitivity adj” on the
ADJUST tab.
ADJUST tab.
Note
The sensitivity of the angular velocity sensor is indicated only on the repairing board, but is not indicated on mass
production boards.
production boards.
FDR-AX30/FDR-AX33/FDR-AXP33/FDR-AXP35
2-10
2-7.
Note on Replacing Projector Unit (Projector Model)
Refer to the following flowchart when repairing or inspecting the projector’s projection function.
If you have received an indication on the projector’s projection function from the customer, check defective part
according to the following flowchart.
When a defective part has been clarified, repair the projector according to the check result.
If you have received an indication on the projector’s projection function from the customer, check defective part
according to the following flowchart.
When a defective part has been clarified, repair the projector according to the check result.
Note
The projector unit (copper plate in particular) becomes hot after it is used.
When replacing a part of the projector unit, wait until it is cooled down. Wipe the lens gently with a soft cloth such as
a cleaning cloth or glass cleaning cloth.
When replacing a part of the projector unit, wait until it is cooled down. Wipe the lens gently with a soft cloth such as
a cleaning cloth or glass cleaning cloth.
Note
Wipe the lens gently with a soft cloth such as a cleaning cloth or glass cleaning cloth.
Stubborn stains may be removed with a soft cloth such as a cleaning cloth or glass cleaning cloth lightly dampened with
water.
Never use a solvent such as alcohol, benzene or thinner; acid, alkaline or abrasive detergent; or a chemical cleaning
cloth, as they will damage the lens surface.
Stubborn stains may be removed with a soft cloth such as a cleaning cloth or glass cleaning cloth lightly dampened with
water.
Never use a solvent such as alcohol, benzene or thinner; acid, alkaline or abrasive detergent; or a chemical cleaning
cloth, as they will damage the lens surface.
Projector problem checking procedure (other than indication on brightness)
Indicated defective
projector received
Measure brightness.
( 2)
Yes
No
OK
OK
NG
NG
OK
NG
A
B
Indication on
brightness
Inspect projector
LED.
( 1)
1 Refer to the ADJUST tab of Adjust Manual.
2 Refer to the SERVICE tab of Adjust Manual.
2 Refer to the SERVICE tab of Adjust Manual.
Inspect projector
LED.
( 1)
END
-
-
-
-
-
-
-
Replace projector unit (light emitting block). (*1)
Replace PJ board. (*1)
Replace both projector unit (light emitting block)
and PJ board. (*1)
Replace PJ board. (*1)
Replace both projector unit (light emitting block)
and PJ board. (*1)
Projector Data Input
Fixed value input
Enter the number on the label attached to the unit.
Enter the number on the label attached to the unit.
Serial number input
LD40
LD40
Syywwnnnnn
Enter the red part.
FDR-AX30/FDR-AX33/FDR-AXP33/FDR-AXP35
2-11
Projector problem checking procedure (indication on brightness)
Yes
No
OK
NG
OK
NG
OK
NG
A
B
Indicated defective
projector received
Measure brightness.
( 2)
Measure brightness.
( 2)
Indication on
brightness
Inspect projector
LED.
( 1)
1 Refer to the ADJUST tab of Adjust Manual.
2 Refer to the SERVICE tab of Adjust Manual.
2 Refer to the SERVICE tab of Adjust Manual.
END
-
-
-
-
-
-
-
Replace projector unit (light emitting block). (*1)
Replace PJ board. (*1)
Replace both projector unit (light emitting block)
and PJ board. (*1)
Replace PJ board. (*1)
Replace both projector unit (light emitting block)
and PJ board. (*1)
Projector Data Input
Fixed value input
Enter the number on the label attached to the unit.
Enter the number on the label attached to the unit.
Serial number input
LD40
LD40
Syywwnnnnn
Enter the red part.
FDR-AX30/FDR-AX33/FDR-AXP33/FDR-AXP35
2-12
Click on the first or last page to see other FDR-AX30 / FDR-AX33 / FDR-AXP33 / FDR-AXP35 service manuals if exist.