Sony DCR-TRV9E Service Manual ▷ View online
— 5 —
DCR-TRV9E
SELF-DIAGNOSIS FUNCTION
1.
SELF-DIAGNOSIS FUNCTION
When problems occur while the unit is operating, the self-diagnosis
function starts working, and displays on the viewfinder what to do.
This function consists of two display; self-diagnosis display and
service mode display.
Details of the self-diagnosis functions are provided in the Instruction
manual.
function starts working, and displays on the viewfinder what to do.
This function consists of two display; self-diagnosis display and
service mode display.
Details of the self-diagnosis functions are provided in the Instruction
manual.
Note:
The self-diagnosis display data will be backed up by the coin-type lithium battery of LI-64 board. When this coin-type lithium battery is disconnected,
the self-diagnosis data will be lost by initialization.
the self-diagnosis data will be lost by initialization.
2.
SELF-DIAGNOSIS DISPLAY
When problems occur while the unit is operating, the counter of the
viewfinder shows a 4-digit display consisting of an alphabet and
numbers, which blinks at 3.2 Hz. This 5-character display indicates
the “repaired by:”, “block” in which the problem occurred, and
“detailed code” of the problem.
viewfinder shows a 4-digit display consisting of an alphabet and
numbers, which blinks at 3.2 Hz. This 5-character display indicates
the “repaired by:”, “block” in which the problem occurred, and
“detailed code” of the problem.
3.
SERVICE MODE DISPLAY
The service mode display shows up to six self-diagnosis codes shown in the past.
3-1.
Display Method
While pressing the “STOP” key, set the switch from OFF to “CAMERA” or “VTR or PLAYER”, and continue pressing the “STOP” key for
10 seconds continuously. The service mode will be displayed, and the counter will show the backup No. and the 5-character self-diagnosis
codes.
10 seconds continuously. The service mode will be displayed, and the counter will show the backup No. and the 5-character self-diagnosis
codes.
3-2.
Switching of Backup No.
By rotating the control dial, past self-diagnosis codes will be shown in order. The backup No. in the [ ] indicates the order in which the
problem occurred. (If the number of problems which occurred is less than 6, only the number of problems which occurred will be shown.)
[1] : Occurred first time
problem occurred. (If the number of problems which occurred is less than 6, only the number of problems which occurred will be shown.)
[1] : Occurred first time
[4] : Occurred fourth time
[2] : Occurred second time
[5] : Occurred fifth time
[3] : Occurred third time
[6] : Occurred the last time
3-3.
End of Display
Turning OFF the power supply will end the service mode display.
Order of previous errors
Backup No.
self-diagnosis codes
C : 3 1 : 1 1
[3]
Lights up
Viewfinder
[3] C : 3 1 : 1 1
1 1
3 1
C
Repaired by:
Refer to page 8.
Self-diagnosis Code Table.
Self-diagnosis Code Table.
Indicates the appropriate
step to be taken.
E.g.
31 ....Reload the tape.
32 ....Turn on power again.
step to be taken.
E.g.
31 ....Reload the tape.
32 ....Turn on power again.
Block
Detailed Code
Blinks at 3.2Hz
C : Corrected by customer
H : Corrected by dealer
E : Corrected by service
H : Corrected by dealer
E : Corrected by service
engineer
Viewfinder
C : 3 1 : 1 1
Control dial
— 6 —
4.
SELF-DIAGNOSIS CODE TABLE
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
E
E
E
E
Block
Function
2
1
2
2
2
3
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
2
3
2
3
2
3
2
3
2
3
2
3
2
3
2
6
1
6
1
6
2
6
2
Detailed
Code
0
0
0
0
0
0
1
0
1
1
2
0
2
1
2
2
2
3
2
4
3
0
4
0
4
2
1
0
1
1
2
0
2
1
2
2
2
3
2
4
3
0
4
0
4
2
0
0
1
0
0
0
0
1
Symptom/State
Condensation.
Video head is dirty.
Non-standard battery is used.
LOAD direction. Loading does not
complete within specified time
complete within specified time
UNLOAD direction. Loading does not
complete within specified time
complete within specified time
T reel side tape slacking when unloading.
Winding S reel fault when counting the
rest of tape.
rest of tape.
T reel fault.
S reel fault.
T reel fault.
FG fault when starting capstan.
FG fault when starting drum.
FG fault during normal drum operations.
LOAD direction loading motor time-
out.
out.
UNLOAD direction loading motor
time-out.
time-out.
T reel side tape slacking when
unloading.
unloading.
Winding S reel fault when counting the
rest of tape.
rest of tape.
T reel fault.
S reel fault.
T reel fault.
FG fault when starting capstan.
FG fault when starting drum
FG fault during normal drum
operations
operations
Difficult to adjust focus
(Cannot initialize focus.)
(Cannot initialize focus.)
Zoom operations fault
(Cannot initialize zoom lens.)
(Cannot initialize zoom lens.)
Steadyshot function does not work well.
(With pitch angular velocity sensor output
stopped.)
(With pitch angular velocity sensor output
stopped.)
Steadyshot function does not work well.
(With yaw angular velocity sensor output
stopped.)
(With yaw angular velocity sensor output
stopped.)
Self-diagnosis Code
Repaired b
y
:
Correction
Remove the cassette, and insert it again after one hour.
Clean with the optional cleaning cassette.
Use the info LITHIUM battery.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
operations from the beginning.
Inspect the lens block focus reset sensor (Pin @¡ of CN452 of CD-
185 board) when focusing is performed when the focus ring is
rotated in the focus manual mode, and the focus motor drive circuit
(IC302 of CD-185 board) when the focusing is not performed.
185 board) when focusing is performed when the focus ring is
rotated in the focus manual mode, and the focus motor drive circuit
(IC302 of CD-185 board) when the focusing is not performed.
Inspect the lens block zoom reset sensor (Pin !¢ of CN452 of CD-
185 board) when zooming is performed when the zoom lens is
operated and the zoom motor drive circuit (IC302 of CD-185 board)
when zooming is not performed.
185 board) when zooming is performed when the zoom lens is
operated and the zoom motor drive circuit (IC302 of CD-185 board)
when zooming is not performed.
Inspect pitch angular velocity sensor (SE451 of cd-185 board)
peripheral circuits.
peripheral circuits.
Inspect yaw angular velocity sensor (SE452 of CD-185 board)
peripheral circuits.
peripheral circuits.
— 7 —
Note:
• Follow the disassembly procedure in the numerical order given.
• Items marked “*” are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these
• Items marked “*” are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these
items.
• The parts numbers of such as a cabinet are also appeared in this section.
Refer to the parts number mentioned below the name of parts to order.
1.
ORNAMENTAL PARTS
MAIN PARTS
DCR-TRV9E
Jack cover (L)
3-988-541-01
3-988-541-01
Remote commander
RMT-809
1-475-141-31
RMT-809
1-475-141-31
Battery lid
3-742-854-21
3-742-854-21
Grip belt
not supplied.
not supplied.
Tapping
3-948-339-61
3-948-339-61
Bracket, belt
*
3-988-540-01
Stopper, belt
3-989-953-01
3-989-953-01
not supplied.
Jack cover (AV)
3-988-427-01
3-988-427-01
Spacer (AV)
*
3-050-908-01
JC pin
3-988-447-01
3-988-447-01
Jack cover (F)
not supplied.
not supplied.
Lens cap assembly
X-3948-452-1
X-3948-452-1
F adaptor assy
X-3948-885-1
X-3948-885-1
Checking supplied accessories.
Check that the following accessories are supplied with your camcorder.
NP-F330 battery pack (1)
(Optional accessory)
(Optional accessory)
Size AA (R6) battery for Remote
Commander (2)
(not supplied)
Commander (2)
(not supplied)
AC-V316 AC power adaptor (1)
X-3948-885-1
The shape of the plug varies from
region to region.
X-3948-885-1
The shape of the plug varies from
region to region.
A/V connecting cable (1)
1-777-433-21
1-777-433-21
Shoulder strap (1)
3-987-015-01
3-987-015-01
Lens cap (1)
X-3948-452-1
X-3948-452-1
Other accessories and packing materials
3-862-549-11 MANUAL, INSTRUCTION (ENGLISH, RUSSIAN)
3-862-549-21 MANUAL, INSTRUCTION (GERMAN, ITALIAN)
3-862-549-31 MANUAL, INSTRUCTION (SPANISH, PORTUGUESE)
3-862-549-41 MANUAL, INSTRUCTION ((FRENCH, GERMAN)
3-948-162-02 EYE CUP
3-862-549-21 MANUAL, INSTRUCTION (GERMAN, ITALIAN)
3-862-549-31 MANUAL, INSTRUCTION (SPANISH, PORTUGUESE)
3-862-549-41 MANUAL, INSTRUCTION ((FRENCH, GERMAN)
3-948-162-02 EYE CUP
21-pin adaptor
1-573-291-11
1-573-291-11
F adaptor assy
X-3948-885-1
X-3948-885-1
— 8 —
Note:
Follow the disassembly procedure in the numerical order given.
2.
F PANEL ASSEMBLY
3.
CABINET (L), CABINET (R) ASSEMBLIES
1
Screw (M2
×
4)
3-968-729-01
2
FP-654 flexible board
1-669-511-11
6
Screw (B2
×
5)
3-948-339-61
4
Screw (B2
×
5)
3-948-339-61
0
MA-322 board
Front panel assembly
X-3948-459-1
X-3948-459-1
3
Function switch block
(MF-4580)
1-475-707-11
(from CN7002 of MA-322 board)
1-475-707-11
(from CN7002 of MA-322 board)
0
MA-322 board
9
Screw (B2
×
5)
3-948-339-61
1
Screw (M2
×
4)
3-968-729-01
7
Connector
(from CN7003 of MA-322 board)
8
Open the jack cover.
not supplied.
Microphone unit
1-542-350-11
1-542-350-11
1
Screw (M2
×
4)
3-968-729-01
Claw
5
Screw (B2
×
5)
3-948-339-61
Microphone holder assembly
X-3948-601-1
X-3948-601-1
!⁄
Cabinet (Upper)
3-988-463-01
2
Screw (M2
×
3)
3-968-729-81
4
Screw (M2
×
4)
3-968-729-01
5
Screw (M2
×
4)
3-968-729-01
4
Screw (M2
×
4)
3-968-729-01
1
Screw (M2
×
3)
3-968-729-81
6
Screw (M2
×
4)
3-968-729-01
8
Harness (BT-55)
(from CN9831 of LI-64 board)
*
Be careful that the harness is fragile and can be easily broken.
In addition, when this harness is removed, the memory backup
power is turned off, and setting of the user's memory
becomes necessary.
power is turned off, and setting of the user's memory
becomes necessary.
7
FP-650 flexible board
1-669-509-21
(from CN7805 of KY-39 board)
(from CN7805 of KY-39 board)
3
Click on the first or last page to see other DCR-TRV9E service manuals if exist.