Sony DCR-TRV9E Service Manual ▷ View online
DCR-TRV9E
RMT-809
AEP Model
UK Model
SERVICE MANUAL
DIGITAL VIDEO CAMERA RECORDER
MICROFILM
C MECHANISM
SPECIFICATIONS
Level 1
— Continued on next page —
Ver 1.0 1998.04
— 2 —
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK
!
OR DOTTED LINE WITH
MARK
!
ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
1.
Check the area of your repair for unsoldered or poorly-soldered
connections. Check the entire board surface for solder splashes
and bridges.
connections. Check the entire board surface for solder splashes
and bridges.
2.
Check the interboard wiring to ensure that no wires are
"pinched" or contact high-wattage resistors.
"pinched" or contact high-wattage resistors.
3.
Look for unauthorized replacement parts, particularly
transistors, that were installed during a previous repair. Point
them out to the customer and recommend their replacement.
transistors, that were installed during a previous repair. Point
them out to the customer and recommend their replacement.
4.
Look for parts which, through functioning, show obvious signs
of deterioration. Point them out to the customer and
recommend their replacement.
of deterioration. Point them out to the customer and
recommend their replacement.
5.
Check the B+ voltage to see it is at the values specified.
6.
Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 270˚C
during repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer.
— 3 —
TABLE OF CONTENTS
SERVICE NOTE
1.
POWER SUPPLY DURING REPAIRS ............................. 4
2.
HOW TO TAKE A CASSETTE OUT WHEN THE MAIN
POWER CANNOT BE TURNED ON ............................... 4
POWER CANNOT BE TURNED ON ............................... 4
SELF-DIAGNOSIS FUNCTION
1.
SELF-DIAGNOSIS FUNCTION ....................................... 5
2.
SELF-DIAGNOSIS DISPLAY .......................................... 5
3.
SERVICE MODE DISPLAY ............................................. 5
3-1.
Display Method .................................................................. 5
3-2.
Switching of Backup No. ................................................... 5
3-3.
End of Display .................................................................... 5
4.
SELF-DIAGNOSIS CODE TABLE ................................... 6
MAIN PARTS
1.
ORNAMENTAL PARTS .................................................... 7
2.
F PANEL ASSEMBLY ...................................................... 8
3.
CABINET (L), CABINET (R) ASSEMBLIES .................. 8
4.
CABINET (R) ASSEMBLY ............................................... 9
5.
EVF ASSEMBLY ............................................................. 10
6.
EVF CABINET (UPPER) ASSEMBLY, EVF CABINET
(LOWER) ASSEMBLIES ................................................ 11
(LOWER) ASSEMBLIES ................................................ 11
7.
LCD ASSEMBLY ............................................................ 12
8.
AU-202 BOARD, DD-106 BOARD,
BATTERY HOLDER ASSEMBLY ................................. 13
BATTERY HOLDER ASSEMBLY ................................. 13
9.
ZOOM LENS ................................................................... 13
10.
VC-206 BOARD .............................................................. 14
11.
MECHANISM DECK ...................................................... 14
12.
CABINET (L) ASSEMBLY ............................................. 15
13.
FP-647 FLEXIBLE BOARD ........................................... 15
GENERAL
Before you begin
Using this manual ................................................................... 16
Checking supplied accessories ............................................... 16
Checking supplied accessories ............................................... 16
Getting started
Charging and installing the battery pack ................................ 16
Inserting a cassette .................................................................. 18
Inserting a cassette .................................................................. 18
Basic operations
Camera recording .................................................................... 18
Hints for better shooting ......................................................... 20
Checking the recorded picture ................................................ 21
Plying back a tape ................................................................... 21
Searching for the end of the picture ........................................ 22
Hints for better shooting ......................................................... 20
Checking the recorded picture ................................................ 21
Plying back a tape ................................................................... 21
Searching for the end of the picture ........................................ 22
Advanced operations
Using alternative power sources ............................................. 22
Changing the mode settings .................................................... 23
Shooting with backlighting ..................................................... 24
Using the FADER function ..................................................... 24
Shooting in the dark (Nightshot) ............................................ 25
Photo recording ....................................................................... 25
Using the wide mode function ................................................ 25
Using the PROGRAM AE function ........................................ 26
Focusing manually .................................................................. 26
Enjoying picture effect ............................................................ 27
Adjusting the exposure ........................................................... 27
Superimposing a title .............................................................. 27
Making a custom title ............................................................. 29
Labeling a cassette .................................................................. 29
Releasing the STEADYSHOT function ................................. 30
Watching on a TV screen ........................................................ 30
Searching the boundaries of recorded tape with
date - date search .................................................................... 31
Searching the boundaries of recorded tape with
title - title search ..................................................................... 32
Searching for a photo - photo search/photo scan .................... 32
Returning to a pre-registered position .................................... 34
Changing the mode settings .................................................... 23
Shooting with backlighting ..................................................... 24
Using the FADER function ..................................................... 24
Shooting in the dark (Nightshot) ............................................ 25
Photo recording ....................................................................... 25
Using the wide mode function ................................................ 25
Using the PROGRAM AE function ........................................ 26
Focusing manually .................................................................. 26
Enjoying picture effect ............................................................ 27
Adjusting the exposure ........................................................... 27
Superimposing a title .............................................................. 27
Making a custom title ............................................................. 29
Labeling a cassette .................................................................. 29
Releasing the STEADYSHOT function ................................. 30
Watching on a TV screen ........................................................ 30
Searching the boundaries of recorded tape with
date - date search .................................................................... 31
Searching the boundaries of recorded tape with
title - title search ..................................................................... 32
Searching for a photo - photo search/photo scan .................... 32
Returning to a pre-registered position .................................... 34
Displaying recording data - data code function ...................... 34
Editing onto another tape ........................................................ 34
Audio dubbing ........................................................................ 35
Editing onto another tape ........................................................ 34
Audio dubbing ........................................................................ 35
Additional information
Usable cassette and playback modes ...................................... 36
Charging the vanadium-lithium battery in the camcorder ...... 36
Resetting the date and time ..................................................... 37
Tips for using the battery pack ............................................... 37
Maintenance information and precautions .............................. 39
Using your camcorder abroad ................................................. 40
Trouble check ......................................................................... 40
Self-diagnosis function ........................................................... 41
Identifying the parts ................................................................ 42
Warning indicators .................................................................. 44
Charging the vanadium-lithium battery in the camcorder ...... 36
Resetting the date and time ..................................................... 37
Tips for using the battery pack ............................................... 37
Maintenance information and precautions .............................. 39
Using your camcorder abroad ................................................. 40
Trouble check ......................................................................... 40
Self-diagnosis function ........................................................... 41
Identifying the parts ................................................................ 42
Warning indicators .................................................................. 44
— 4 —
DCR-TRV9E
SERVICE NOTE
1.
POWER SUPPLY DURING REPAIRS
In this unit, about 10 seconds after power is supplied (8.4V) to the
battery terminal using the service power cord (J-6082-223-A), the
power is shut off so that the unit cannot operate.
This following two methods are available to prevent this. Take note
of which to use during repairs.
battery terminal using the service power cord (J-6082-223-A), the
power is shut off so that the unit cannot operate.
This following two methods are available to prevent this. Take note
of which to use during repairs.
Method 1.
Connect the servicing remote commander RM-95 (J-6082-053-B)
to the LANC jack, and set the remote commander switch to the
“ADJ” side.
to the LANC jack, and set the remote commander switch to the
“ADJ” side.
Method 2.
Press the following battery switch using adhesive tape, etc.
2.
HOW TO TAKE A CASSETTE OUT
WHEN THE MAIN POWER CANNOT
BE TURNED ON
WHEN THE MAIN POWER CANNOT
BE TURNED ON
Note:
To take a cassette out forcibly as follows when the main power
cannot be turned on, remove the cabinet (R) assembly. Apply +4.5
V power from an external power supply to the FP-594 flexible board
that is removed from CN3106 of the VC-206 board, as shown below.
Refer to sections 2-1 and 2-2 for the procedure to remove the cabinet
(R) assembly.
V power from an external power supply to the FP-594 flexible board
that is removed from CN3106 of the VC-206 board, as shown below.
Refer to sections 2-1 and 2-2 for the procedure to remove the cabinet
(R) assembly.
Procedure:
1)
1)
Open the cassette lid.
2)
Apply +4.5 V directly to the FP-594 flexible board as shown to
drive the loading motor that ejects a cassette.
drive the loading motor that ejects a cassette.
Battery terminal
‘
Battery switch
Battery SIG terminal
Battery terminal
’
FP-594
flexible
board
flexible
board
Pins-24/-25
(wide pattern)
(wide pattern)
1
27
Pin-26/-27
(wide pattern)
(wide pattern)
: unloading
: loading
: loading
