Sony DCR-TRV38 / DCR-TRV38E / DCR-TRV39 (serv.man3) Service Manual ▷ View online
37
Recording – Basics
Checking recordings – End search/Edit search/Rec Review
Edit search
You can search for the next recording start point. You cannot monitor the sound.
(1) Set the POWER switch to CAMERA.
(2) Hold down the EDITSEARCH. The recorded portion is played back.
(2) Hold down the EDITSEARCH. The recorded portion is played back.
Release EDITSEARCH to stop playback. If you press START/STOP, recording
begins from the point you released EDITSEARCH.
begins from the point you released EDITSEARCH.
7 – : To go backwards
+ : To go forwards
Rec Review
You can check the last recorded section.
(1) Set the POWER switch to CAMERA.
(2) Press the 7 – side of EDITSEARCH momentarily.
(2) Press the 7 – side of EDITSEARCH momentarily.
The section you have stopped most recently will be played back for a few
seconds, and then your camcorder will return to standby.
seconds, and then your camcorder will return to standby.
38
You can monitor the recorded tape on the LCD screen. If you close the LCD panel, you
can monitor the playback picture in the viewfinder. You can also control playback using
the Remote Commander supplied with your camcorder.
can monitor the playback picture in the viewfinder. You can also control playback using
the Remote Commander supplied with your camcorder.
(1) Set the POWER switch to VCR while pressing the small green button.
(2) Press OPEN to open the LCD panel.
(3) Press
(2) Press OPEN to open the LCD panel.
(3) Press
to rewind the tape.
(4) Press
to start playback.
(5) Adjust the volume following the steps below.
1
Press FN to display PAGE1.
2
Press VOL. The screen to adjust volume appears.
3
Press – (to turn down the volume)/+ (to turn up the volume).
4
Press
OK to return to PAGE1.
— Playback – Basics —
Playing back tape
4
3
1
2
VCR
MEMORY/
NETWORK
CAMERA
OFF(CHG)
POWER
5
VOL
–
+
OK
The bar indicator
39
Playback – Basics
To return to FN
Press EXIT.
To cancel playback
Press
.
To rewind the tape
Press
during playback stop.
To fastforward the tape
Press
during playback stop.
To view a still image (playback pause)
Press
during playback. To resume playback, press
again.
If you leave the power on for a long time
Your camcorder gets warm. This is not a malfunction.
Your camcorder gets warm. This is not a malfunction.
To display the screen indicators – Display function
Press DISPLAY/BATTERY INFO on your camcorder or DISPLAY on the Remote
Commander supplied with your camcorder.
The indicators disappear from the screen.
To make the indicators appear, press DISPLAY/BATTERY INFO or DISPLAY on the
Remote Commander again.
Commander supplied with your camcorder.
The indicators disappear from the screen.
To make the indicators appear, press DISPLAY/BATTERY INFO or DISPLAY on the
Remote Commander again.
Note
Even if you press DISPLAY on the Remote Commander with the POWER switch set to
OFF(CHG), the BATTERY INFO indicator is not displayed.
Even if you press DISPLAY on the Remote Commander with the POWER switch set to
OFF(CHG), the BATTERY INFO indicator is not displayed.
Playing back tape
DISPLAY/
BATTERY INFO
BATTERY INFO
DATA CODE
DISPLAY
40
About date/time and various settings
Your camcorder automatically records not only images on the tape but also the
recording data (date/time or various settings when recorded) (Data code).
Follow the steps below to display the data code using the touch panel or the Remote
Commander.
recording data (date/time or various settings when recorded) (Data code).
Follow the steps below to display the data code using the touch panel or the Remote
Commander.
Using the touch panel
(1) Set the POWER switch to VCR, then play back the tape.
(2) During playback, press FN and select PAGE2.
(3) Press DATA CODE.
(4) Select CAM DATA or DATE DATA, then press
(2) During playback, press FN and select PAGE2.
(3) Press DATA CODE.
(4) Select CAM DATA or DATE DATA, then press
OK.
(5) Press EXIT.
[a] Tape counter
[b] SteadyShot off
[c] Exposure
[d] White balance
[e] Gain
[f] Shutter speed
[g] Aperture value
[b] SteadyShot off
[c] Exposure
[d] White balance
[e] Gain
[f] Shutter speed
[g] Aperture value
Using the Remote Commander
Press DATA CODE on the Remote Commander during playback.
The display changes as follows:
date/time
The display changes as follows:
date/time
t various settings (SteadyShot off, exposure, white balance, gain, shutter
speed, aperture value)
t (no indicator)
Various settings
Various settings shows your camcorder’s recording information at the time of
recording. During tape recording standby, the various settings will not be displayed.
Various settings shows your camcorder’s recording information at the time of
recording. During tape recording standby, the various settings will not be displayed.
When you use data code, bars (-- -- --) appear if:
– A blank portion of the tape is being played back.
– The tape is unreadable due to tape damage or noise.
– The tape was recorded by a camcorder without the date and time set.
– A blank portion of the tape is being played back.
– The tape is unreadable due to tape damage or noise.
– The tape was recorded by a camcorder without the date and time set.
Data code
When you connect your camcorder to a TV, the data code also appears on the TV
screen.
When you connect your camcorder to a TV, the data code also appears on the TV
screen.
Playing back tape
Date/time
JUL 4 2003
12:05:56 PM
12:05:56 PM
50min
0:00:23:01
AUTO
50min
0:00:23:01
6 0 AWB
F1.8 9 dB
[a]
[b]
[c]
[d]
[c]
[d]
[e]
[f]
[g]
[g]
Various settings
Click on the first or last page to see other DCR-TRV38 / DCR-TRV38E / DCR-TRV39 (serv.man3) service manuals if exist.